Assigning Remote Controls; Programming The Remote Control's Buttons - Magellan MG-6060 Reference And Installation Manual

The signal strength is displayed using two terms:
• "Good": This is an average reading and is acceptable.
• "Weak": This is the weakest reading. The transmitter should
be moved to another location. Sometimes moving the
transmitter by a small amount will greatly increase the signal
reception.
To view the signal strength of a wireless transmitter:
1. Access the installer programming mode (page 11).
2. Enter the [ ] corresponding to the desired zone or
SECTION
doorbell.
3. The LCD will display either "Good" or "Weak" on the screen.
When performing a signal strength test, Magellan also displays
the noise level surrounding each of the transmitters. "Low"
refers to a low level of noise while "High" refers to a noisy
environment.
The signal strength can also be verified by performing a
system test. See Quick Setup on page 4 for more
information.

Assigning Remote Controls

Sections [041] to [056]: Users 1 to 16; Remote Controls 1 to 16
The Magellan console accepts up to 16 fully programmable
remote controls. Every user code can have one remote control
assigned to it.
To assign a remote control:
MENU
1. Press [ ] + [4] + [2].

Programming the Remote Control's Buttons

Sections [161] to [176]: Users 1 to 16; Remote Controls 1 to 16
Sections [161] to [176] represent the remote controls assigned to
user codes 1 to 16 (see Table 4 on page 18).
The remote control will transmit a signal for only 1 second when
a button is pressed. This is done to conserve the remote
control's batteries.
Though remote controls can be assigned by the System Master,
the remote control's buttons are programmed by the installer.
Each remote control can be programmed to perform up to 5
different actions. Each digit in sections [161] to [176] represents
a button or combination of buttons (see Table 4 on page 18).
To program a remote control's buttons:
1. Access the installer programming mode (page 11).
2. Enter the [ ] (sections [161] to [176]) corresponding
SECTION
to the desired remote control.
3. Enter the [
HEXADECIMAL VALUE
button option from Table 20 (page 19).
If you do not wish to program all the buttons or button
combinations, press the [#] key at any time to save and exit.
If you enable any Panic button options, you must enable the
Panic options in the control panel (refer to Panic Alarms on
page 23).
18
] (0 to D) of the desired
Table 4: Remote Control Button Programming
Section
Data (refer to Table 20 on page 19)
#
[161] _____/_____/_____/_____
[162] _____/_____/_____/_____
[163] _____/_____/_____/_____
[164] _____/_____/_____/_____
[165] _____/_____/_____/_____
[166] _____/_____/_____/_____
[167] _____/_____/_____/_____
[168] _____/_____/_____/_____
[169] _____/_____/_____/_____
[170] _____/_____/_____/_____
[171] _____/_____/_____/_____
[172] _____/_____/_____/_____
[173] _____/_____/_____/_____
[174] _____/_____/_____/_____
[175] _____/_____/_____/_____
[176] _____/_____/_____/_____
Figure 19: Remote Control Button Identification
MG-REM1
Remote Control 1
+
Remote Control 2
+
Remote Control 3
+
Remote Control 4
+
Remote Control 5
+
Remote Control 6
+
Remote Control 7
+
Remote Control 8
+
Remote Control 9
+
Remote Control 10
+
Remote Control 11
+
Remote Control 12
+
Remote Control 13
+
Remote Control 14
+
Remote Control 16
+
Remote Control 16
+
The button of the MG-REM1
remote control has been permanently
programmed to disarm the system.
The button's functionality cannot be
altered.
The + , + and
button combinations do not function
with the MG-REM1 remote control.
Reference & Installation Manual
User
#
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
+