Related Manuals for Bose VIDEOWAVE
Summary of Contents for Bose VIDEOWAVE
- Page 1 Setup Guide Guía de instalación Guide d’installation ™ IDEO NTERTAINMENT YSTEM...
- Page 2 Replace only with batteries of the correct type and model number. All Bose products must be used in accordance with local, state, Please dispose of used batteries properly, federal, and industry standards. following any local regulations. Do not incinerate.
- Page 3 English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 AFETY NFORMATION • Allowing children to push, pull, or climb on the monitor may cause Notes: it to tip over, possibly resulting in personal injury or death. •...
- Page 4 English AFETY NFORMATION Notice Bose Corporation hereby declares that this product is in compliance with the essential requirements and other This equipment has been tested and found to comply with the relevant provisions of Directive 1999/5/EC and other limits for a Class B digital device, pursuant to Part 15 of the FCC applicable Directives.
-
Page 5: Table Of Contents
English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 ONTENTS ELCOME Thank you ....... Product overview . - Page 6 TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English...
-
Page 7: Welcome
There are two parts to the setup process: • Physical setup – This part of the setup includes The VideoWave system features a 46-inch monitor, placing the monitor and control console and making and comes with a control console, a remote control, system connections. -
Page 8: Physical Setup
3 - 10 ft. 3 - 10 ft. Direct (0.9 - 3.0 m) (0.9 - 3.0 m) VideoWave™ entertainment system. sound Monitor placement recommendations Much like a live performance in a concert hall, the Side Side... -
Page 9: Placing The Monitor With Attached Stand
2. On the rear panel of the monitor, firmly pull out on the bottom of the connector cover to remove it. Connector cover Anti-tip straps *Not rated for in-wall use. In-wall cables are available from Bose or a Bose authorized dealer. -
Page 10: Installing The Anti-Tip Straps
AC (mains) outlet. 6. Go to “Control console placement and connec- tions” on page 14 to continue the physical setup. CAUTION: Bose strongly recommends installing the Monitor cable two included anti-tip straps that, when properly installed, provide an extra measure of security in the event that the AC power monitor accidentally starts to tip over. - Page 11 English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 HYSICAL ETUP 1. Using a 5/32" (4 mm) T-handle hex wrench (not CAUTION: The included screws are for use only into included), remove the top two bolts from the rear wood-studded wall constructions with one-inch (max.) panel of the monitor as indicated.
-
Page 12: Wall-Mounting The Monitor
Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English HYSICAL ETUP Wall-mounting the monitor 5. Using a 7/64" (3 mm) drill bit (not included), drill four pilot holes. 1. - Page 13 English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 HYSICAL ETUP 3. Remove the two stand bolts using a 5/32" (4 mm) WARNING: The monitor weighs about 110 lbs. Allen wrench (not included).
-
Page 14: Control Console Placement And Connections
Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English HYSICAL ETUP Control console placement CAUTION: If using the monitor on the stand, DO NOT and connections place the control console between the legs of the stand or anywhere directly under the bottom edge of the moni- tor. - Page 15 English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 HYSICAL ETUP 2. Plug the free end of the monitor cable into the 3. Plug the power supply output cord into the control connector labeled A/V OUT to Monitor on the console Power connector.
-
Page 16: Nteractive Setup
You need these items from Kit 2: HDMI cable (2) Component Stereo audio video cable cable Bose ® click pad remote control with batteries ® ADAPTiQ audio calibration headset Composite IR emitter video cable... - Page 17 Note: When the system starts up, you will hear a start-up console. The power light on the control tone, and on the monitor screen you will see the Bose console indicates the startup status. logo with a progress bar under it.
-
Page 18: If You Have Setup Problems
If you experience setup problems, the Unify intelligent “Press and hold the OK button on the Bose remote integration system can help you identify the issue. until the screen turns black.”... - Page 19 English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 NTERACTIVE SETUP...
- Page 20 ©2010 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM320988 Rev.01...