Operation; Using The Remote Control; Turning On The Mas System; Setting The Clock - Harman Kardon MAS 101 Owner's Manual

MAS SYSTEM
Using the MAS system is simple and intuitive. The front-panel controls use advanced
touch-sensitive technology. To use the front panel, place a finger over any of the illuminated
icons. A gentle tap is all that is necessary. Wait a few seconds for the system to process
each command. To remove fingerprints, wipe the front panel with a dry microfiber cloth.

Using the Remote Control

Point the remote at the front of the MAS system. The remote IR sensor is located on
the right half of the front panel of the controller. Do not block the sensor. The remote
has a range of approximately 6m, up to 30 degrees off center. If the batteries require
replacement, see Step 2 of the Installation section. Use caution and dispose of batteries
according to environmental requirements. Never throw the batteries into fire, and remove
them from the remote if the remote will be unused for a long period of time.

Turning on the MAS System

To turn on the MAS system, press and hold the Power button on the remote or the controller
for 1 second. The system will also turn on when one of the Source Selectors, the Eject
button or the Play/Pause button on the remote is pressed.
Press the Power button to turn off the system. If the clock has been turned off, the
message display will go dark to conserve power. Otherwise, the time will be displayed
at half-brightness.

Setting the Clock

The clock may be set using the Settings menu. See Figure 2.
1. Press the Settings button on the remote.
2. Press the 7/3 buttons until "Time Setup" appears in the message display.
Figure 2: Setting the Clock
S e t t i n g s
>
S p e a k e r S e t u p
T i m e S e t u p
C l o c k
Enter
C l o c k
O f f
3. Press the Enter button to display "Clock."
Turn the clock on or off: Press the Enter button and use the 7/3 buttons to select "On"
or "Off." Turning the clock off conserves power when the system is powered down to
Standby mode.
4. Set the clock: Press the 7/3 buttons until "Set Clock" appears on the lower line. Press
the Enter button to display "Set Time."
5. Set the day of the week: Press the 7/3 buttons until "Set Day" appears. Press the Enter
button to display the day of the week, and use the 7/3 buttons to select the desired day.
Press the Enter or Back button to save the changes.

Setting the Alarms

For automatic turn-on at a programmed time, set one or both of the alarms. The alarms
may be set using the Settings menu. See Figure 3 on page 12.
1. Press the Settings button on the remote.
2. Press the 7/3 buttons until "Alarm Setup" appears in the message display.
Right
S e t t i n g s
<
T i m e S e t u p
Left
Enter
Right
T i m e S e t u p
>
S e t C l o c k
Left
Enter or Back
Enter
>
S e t C l o c k
S e t T i m e
Enter
S e t T i m e
1 2 : 4 3
Set the time: Press the Enter button and use the numeric keys to enter the hour,
then the minute. If the 12-hour time format is active, use the 7/3 buttons to select
"AM" or "PM." Press the Enter button to advance from one field to the next without
changing it, and press the Enter or Back button to save the settings.
Set the format: Press the 7/3 buttons until "Set 12/24 hour" appears. Press the
Enter button to change the format, and use the 7/3 buttons to select between
the 12- and 24-hour time displays. Press the Enter or Back button to save the
change.
>
Back
Right
T i m e S e t u p
<
>
Left
Enter
Back
Right
S e t C l o c k
<
>
S e t 1 2 / 2 4 h o u r
Left
Enter
Enter or Back
S e t 1 2 / 2 4 h o u r
>

Operation

S e t D a y
Enter or Back
S e t D a y
>
M o n d a y
>
Enter or Back
>
1 2 h o u r
11