Long Operation; Econo Cool Operation; Timer Operation (On/Off Timer) - Mitsubishi Electric MS-GA50VB Operating Instructions Manual

LONG OPERATION

Use this operation when you want the air flow to reach a long distance.
Perform the following operations while the unit is operating.
■
Press the
˚C
The fan speed increases.
CLOCK
AMPM When the fan speed is set to
speed determined by the room temperature and the set temperature.
AMPM
In addition, the HORIZONTAL VANE moves to the position for LONG mode.
TOO TOO
ON/OFF
WARM COOL
Mechanism of the LONG operation
In the following example, the VERTICAL VANE is set to
FAN STOP
I FEEL COOL
VANE START
HEAT DRY
MODE WIDE VANE HR.
ECONO COOL LONG MIN.
RESET CLOCK
Fan speed: Higher
Solid arrow: When the LONG mode is used
Dotted arrow: When the LONG mode is not used
To release the LONG mode:
■
Press the
■ LONG mode is also released in the following ways.
• By pressing the
• By pressing the
■ Even when the LONG mode is being used, the air may not reach a long distance
due to the installation location of the air conditioner.
In this case, press the
then press the
MODE
,
■
are available.
8
LONG
button.
(AUTO), the fan speed is higher than a fan
COOL/DRY HEAT/FAN
LONG
button again.
VANE
button
ECONO COOL
button (only during COOL mode)
FAN
button to set the fan speed to
LONG
button.
FAN
WIDE VANE
, and buttons, temperature buttons and the ON/OFF timer

ECONO COOL OPERATION

Use this operation when you want to be comfortable in COOL mode even with energy saved.
˚C
CLOCK
AMPM
AMPM
TOO TOO
ON/OFF
WARM COOL
(front).
FAN STOP
I FEEL COOL
VANE START
HEAT DRY
MODE WIDE VANE HR.
ECONO COOL LONG MIN.
RESET CLOCK
What is "ECONO COOL"?
Swing air flow (change of air flow) makes you feel cooler than constant air flow. So, even though the set temperature is automati-
cally set 2°C higher, it is possible to perform cooling operation with keeping comfort. As a result, energy can be saved.

TIMER OPERATION (ON/OFF TIMER)

It is convenient to set the timer when you go to bed, when you get home, when you get up, etc.
How to set the ON timer
1 START
Press the button during operation.
Each time the button is pressed, the ON timer mode
alternates between ON and OFF.
2
Set the time of the timer using the
MIN.
buttons.
HR.
Each time the button is pressed, the set time
increases by 1 hour; each time the
(High) , and
pressed, the set time increases by 10 minutes.
To release the ON timer:
■
START
Press the button.
Programming timer operation
The ON timer and the OFF timer can be used in combination. The timer of the set time that is reached first will operate first.
(" " mark indicates the order of timer operations.)
• If the current time has not been set, the timer operation cannot be used.
NOTE:
If the main power is turned off or a power failure occurs while AUTO START/STOP timer is active, the timer setting is
cancelled. As these models are equipped with an auto restart function, the air conditioner starts operating with timer
cancelled at the same time that power is restored.
Perform the following operations while the unit is operating
in the MANUAL COOL mode.
■ ECONO COOL
Press the button.
When the (ECONO COOL) operation is selected in COOL mode, the air
conditioner performs swing operation in various cycle according to the
temperature of air conditioner.
Also SET TEMPERATURE is automatically set 2°C higher than in COOL mode.
To release the ECONO COOL operation:
■ ECONO COOL
Press the button again.
VANE
LONG
• When the button or the button is pressed or the operation mode
is changed during the ECONO COOL operation, ECONO COOL operation is
released.
TOO TOO
WARM COOL
FAN
• The button, the or button and ON/OFF timer (explained below)
are available.
How to set the OFF timer
1
STOP
Press the button during operation.
Each time the button is pressed, the OFF timer mode
alternates between ON and OFF.
HR.
2
and Set the time of the timer using the
MIN.
buttons.
HR.
Each time the button is pressed, the set time
MIN. increases by 1 hour; each time the
button is
the set time increases by 10 minutes.
To release the OFF timer:
■ STOP
Press the button.
HR.
and
MIN.
button is pressed,