Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SoundCraft DPS-3
Summary of Contents for SoundCraft DPS-3
-
Page 1: User Guide
Soundcraft D D PS-3 3 P P ower S S upply USER GUIDE TECHNICAL MANUAL... - Page 2 Soundcraft shall not be liable for loss or dam- age whatsoever arising from the use of information or any error contained in this manual.
-
Page 3: Table Of Contents
Contents Safety Symbol Guide ......................4 Important Safety Instructions ....................5 Fitting The Feet Or Rackmounting ..................7 Connecting Up ........................8 Pin-outs Of DC Output Connector ...................8 Circuit Diagram ........................9 PCB Layout ..........................10 Parts List ..........................11 Dimensions .........................14 Warranty ..........................15... -
Page 4: Safety Symbol Guide
SAFETY S S YMBOL G G UIDE For your own safety and to avoid invalidation of the warranty all text marked with these Symbols should be read carefully. CAUTIONS Must be followed carefully to avoid bodily injury. WARNINGS Must be observed to avoid damage to your equipment. NOTES Contains important information and useful tips on the operation of your equipment. -
Page 5: Important Safety Instructions
Refer all servicing to qualified service personnel. It is recommended that all mainte- nance and service on the product should be carried out by Soundcraft or its autho- rised agents. Soundcraft cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel. - Page 6 THIS APPARATUS MUST BE EARTHED. Under no circumstances should the safety earth be disconnected from the mains lead. The mains supply disconnect device is the mains plug. It must remain accessible so as to be readily operable when the apparatus is in use. If any part of the mains cord set is damaged, the complete cord set should be replaced.
-
Page 7: Fitting The Feet Or Rackmounting
FITTING T T HE F F EET O O R R R ACKMOUNTING... -
Page 8: Connecting Up
Screw the connector locking ring clockwise on both units to secure the cable. The locking ring should be firm, but not tight. Connect an IEC type mains cable with the plug fused at 3 AMPS, to the mains input socket on the DPS-3. Connect the other end to the nearest plug socket and switch on the power to the DPS-3. -
Page 9: Circuit Diagram
Circuit Diagram... -
Page 10: Pcb Layout
PCB Layout... -
Page 11: Parts List
PARTS LIST GB4 PSU ASSY R0050A-04-AF Ident Description Part Number — GB4 PCB PSU BOARD S0050A-04 — HEATSINK THERMALOY 7121D XV05- PN10004 — POWER STN MIXER PSU HEATSINK PN1240 — DRIVER MOUNTING CLIP ZC0231 — (Safety Critical Part)! FUSE 5X20MM T 2A 250V ZD8002 BDG RECT KBU6K SIL 6A 800V BC0222... - Page 12 DIODE FAST TYPE EGP10G 400V 1A BA10014 TL431 SHUNT REGULATOR TO92 BE0503 (Safety Critical Part)! FUSE HOLDER 6.3A PCB MTG ZD8023 VOLTAGE MODE PWM DIP-14 BE10032 INDUCTOR-OUTPUT -GB4/RENO P0009-01 FERRITE BEAD AX 5X3.5MM TAPED HC0021 INDUCTOR 10UH TOKO A823LY-100K HC0028 INDUCTOR 10UH TOKO A823LY-100K HC0028 INDUCTOR 10UH TOKO A823LY-100K...
- Page 13 SP13 SPADE TAB VERT PC 0.125C FF10022 SP14 SPADE TAB VERT PC 0.125C FF10022 SP15 SPADE TAB VERT PC 0.125C FF10022 SP16 SPADE TAB VERT PC 0.125C FF10022 (Safety Critical Part)! PANASONIC DPST HOR MAINS SWT DJ8002 TRANSFORMER SMPS.GB4/RENO P0008-01 (Safety Critical Part)! THERMISTER 3A INRUSH LIMITER AZ2279...
-
Page 14: Dimensions
DIMENSIONS... -
Page 15: Warranty
Equipment has been properly installed in accordance with instruc- tions contained in Soundcraft’s manual; and b) the End User has notified Soundcraft or the Dealer within 14 days of the defect appearing; and c) no persons other than authorised representatives of Soundcraft or the Dealer have effected any replacement of parts maintenance adjustments or repairs to the Equipment;... - Page 16 Soundcraft shall not be liable for loss or dam- age whatsoever arising from the use of information or any error contained in this manual.