Power Supply - Panasonic NV-MX500B Operating Instructions Manual

3
Insert the Battery Holder into the Remote Controller.
≥When the button-type battery is exhausted, replace it with a
new CR2025 battery. (A battery is normally expected to last
about 1 year. However, it depends on operation
frequency.)
≥Make sure to match the poles correctly when inserting the
battery.
WARNING
"THE LITHIUM BATTERY IS A CRITICAL
COMPONENT (TYPE NUMBER CR2025
MANUFACTURED BY PANASONIC).
IT MUST NEVER BE SUBJECTED TO EXCESSIVE
HEAT OR DISCHARGE. IT MUST THEREFORE ONLY
BE FITTED IN EQUIPMENT DESIGNED
SPECIFICALLY FOR ITS USE.
REPLACEMENT BATTERIES MUST BE OF THE SAME
TYPE AND MANUFACTURER.
THEY MUST BE FITTED IN THE SAME MANNER AND
LOCATION AS THE ORIGINAL BATTERY, WITH THE
CORRECT POLARITY CONNECTIONS OBSERVED.
DO NOT ATTEMPT TO RE-CHARGE THE OLD
BATTERY OR RE-USE IT FOR ANY OTHER
PURPOSE. IT SHOULD BE DISPOSED OF IN WASTE
PRODUCTS DESTINED FOR BURIAL RATHER THAN
INCINERATION."
ª Using the Remote Controller
1
Direct the Remote Controller to the Remote Control
Sensor (48) of the Movie Camera and press an
appropriate button.
5˚
15˚
15˚
≥Distance from the Movie Camera: Within approximately
5 metres
≥Angle: Within approximately 5o in the upward, and 15o in
the downward and horizontal directions from the central
axis
≥The above operative ranges are for indoor use. Outdoors
or under strong light, the Movie Camera may not operate
properly even within the above ranges.
≥Within a 1-metre range, you can also use the Remote
Controller on the LCD Monitor side of the Movie Camera.
Selecting Remote Controller Modes
When 2 Movie Cameras are used simultaneously, they can
be operated individually by selecting different Remote
Controller Modes.
≥If the Remote Controller Mode of the Movie Camera and
that of the Remote Controller do not match, [REMOTE]
Indication is displayed.
Setup on the Movie Camera:
Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to
the desired Remote Controller Mode. (
(48)
15˚
)
-11-
Before Use
Setup on the Remote Controller:
2
[VCR1]:
Press the [D] Button and [∫] Button simultaneously. 1
[VCR2]:
Press the [E] Button and [∫] Button simultaneously. 2
≥When the battery in the Remote Controller is replaced, the
mode is automatically reset to [VCR1] Mode.

Power Supply

ª Using the AC Adaptor
1
Connect the DC Input Lead to the Movie Camera.
2
Connect the DC Input Lead to the AC Adaptor.
3
Connect the AC Mains Lead to the AC Adaptor and the
AC mains socket.
≥The AC Mains Lead's outlet plug does not fit entirely into
the AC Adaptor socket. A gap will remain as shown 1.
≥Before connecting or disconnecting the power supply,
set the [OFF/ON/MODE] Switch on the Movie Camera to
[OFF] and make sure that [CAMERA/VCR/CARD P.B]
Lamps are not lit.
ª Using the Battery
Before use, fully charge the Battery.
1
Attach the Battery to the AC Adaptor and charge it.
≥Since the Battery will not be charged when the DC Input
Lead is connected to the AC Adaptor, disconnect it from
the AC Adaptor.
≥After the [POWER] Lamp has lighted, the [CHARGE]
Lamp flashes.
2
When the [100%] Lamp 1 on the AC Adaptor is
lighted, charging is finished.
POWER
≥When the [QUICK] Lamp 2 is lighted, approximately
50 minutes of continuous recording is possible.
≥The [QUICK] Lamp flashes and then remains lighted only
when charging a quick-charge type battery.
-7-
T
W
6 1 5
STILL ADV PAUSE STILL ADV
1
E ; D
INDEX STOP INDEX
K L
∫
SELECT
1
2 1
CHARGE
QUICK 100%