Speaker Settings - Panasonic SC-XH10 Operating Instructions Manual

Audio menu
Dynamic Range
≥ On: Adjusts for clarity even when the volume is low. Convenient for
late night viewing. (Only works with Dolby Digital)
≥ Off: The full dynamic range of the signal is reproduced.

Speaker Settings

Select the delay time of the speakers.
(Effective only when "Surround layout (Recommended)" mode is selected
in "Speaker layout" ( 8, Easy setup).)
(Center and surround speakers only)
For optimum listening with 5.1-channel sound, all the speakers, except for
the subwoofer, should be the same distance from the seating position.
If you have to place the center or surround speakers closer to the seating
position, adjust the delay time to make up for the difference.
:
C
L C R
:
SW
LS Approximate room dimensions
RS
LS RS
Circle of constant primary listening distance
If either distance a or b is less than c, find the difference in the table
and change to the recommended setting.
a Center speaker
Difference (Approx.) Setting
30 cm 1ms
60 cm 2ms
90 cm 3ms
120 cm 4ms
150 cm 5ms
≥ C Delay (Center Delay):
0ms, 1ms, 2ms, 3ms, 4ms, 5ms
Select the delay time for your center speaker.
≥ LS/RS Delay (Left Surround/Right Surround Delay):
0ms, 5ms, 10ms, 15ms
Select the delay time for your surround speakers.
≥ Test Tone:
Use the test tone to listen to the speaker output to confirm speaker
connections.
Test tone will be output to each channel in the following order.
Left, Center, Right, Surround Right, Surround Left, Subwoofer
To stop the test tone, press [RETURN]D.
Actual speaker position
Ideal speaker position
:
Primary listening
distance
b Surround speaker
Difference (Approx.)
150 cm
300 cm
450 cm
Others menu
DivX Registration
Display the unit's registration code.
You need this registration code to purchase and play DivX Video-on-
Demand (VOD) content (
DivX Deregistration
Display the unit's deregistration code.
You need this deregistration code to cancel this unit's registration (
This setting is only selectable after playing DivX VOD content for the first
time.
Auto AUX Link
≥ On: When this unit is in standby mode, this unit will turn on and
change the source to "AUX" when there is an audio signal to
the AUX terminal. (
≥ Off
Slide Show Time
Set the speed of the slideshow.
≥ 3 Seconds ≥ 5 Seconds
Easy setup
You can execute basic settings to optimise your home theater system.
( 8)
FL Dimmer
Change the brightness of the unit's display.
≥ Bright
≥ Dim: The display is dimmed.
Setting
≥ Auto: The display is dimmed, but brightens when you perform some
5ms
operations.
10ms
15ms
Screen Saver
This is to prevent burn marks on the TV screen.
≥ Off
≥ Wait 5 min: If there is no operation for 5 minutes, the screen saver will
be shown. The TV screen will resume when you perform
some operations. (This does not work during playback.)
Ratings
Set a rating level to limit DVD-Video play.
Setting ratings (When level 8 is selected)
≥ 1 to 7
≥ 8 No Limit
When you select your ratings level, a password screen is shown.
The default password is "8888".
Enter the 4-digit password with the numbered buttons, and press [OK]8.
You can change the default password (
Do not forget your password.
A message screen will be shown if a DVD-Video disc exceeding the rating
level is inserted in the unit.
Follow the on-screen instructions.
Set Password
Change the password for "Ratings".
When you change the password for the first time:
The default password is "8888".
Follow the on-screen instructions.
Restore Default Settings
This returns all values in the Setup menu to the default settings except the
password and ratings level.
Press [2, 1]8 to select "Yes" and press [OK]8.
Turn the unit off and on again.
[DivX]
16).
[DivX]
9)
≥ 10 Seconds
below)
16).
≥ 15 Seconds
15
15