Ir Repeater Connection - Pioneer VSX-D3S Operating Instruction

CONNECTIONS

IR REPEATER CONNECTION

Connecting a supplied IR Repeater lets you also control other components with this unit's remote control.
NOTE:
To operate components not made by Pioneer, perform REMOTE SET UP (page 31) after connecting an IR Repeater.
Remote control signals directed towards this unit or GUI operation signals are transmitted from the repeater as infrared signals, enabling
control of other components.
There are two kinds of infrared repeaters. Connect either or both to match the remote control requirements of different components.
MAIN-REPEATER
Use this to operate other components with this unit's remote
control or to operate using GUI on-screen indications.
Install on top of this unit as shown in the figure.
MAIN-REPEATER
CONTROL
VIDEO OUT
SYSTEM CONTROL
GND IR OUT
TO MONITOR TV
PAL NTSC MAIN-
IN
REPEATER
PHONO
IN OUT
FM 50kHz 100kHz
/50 S /75 S
VCR2 OUT
AM 9kHz 10kHz
REC
CHANNEL STEP IN
1 2
/FM DE- EMPHASIS
TAPE2
MINI-
MONI-
REPEATER
OUT
TOR
S
FM VCR1
PLAY OUT
BAL
REC
300
IN S
IN
TAPE1
FM
LD
UNBAL S
IN
75 PLAY
IN
TV
GND TO
CD IN
S
/SAT MONITOR
OUT
TV
IN
R L R L VIDEO
AM
SEE INSTRUCTION MANUAL
LOOP
ANTENA
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
ANTENNA
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
Illustration shows Multi-voltage model.
MINI-REPEATER
Use this when a component operates incorrectly after receiving
a signal from this unit's remote control, or when it is difficult for
a component to receive signals from the Main-Repeater. Stick it
directly on the remote control sensor window.
There are two MINI-REPEATER terminals.
If you need another Mini-Repeater, contact you nearest Pioneer
Service Center.
MINI-REPEATER
CONTROL
VIDEO OUT
GND
TO MONITOR TV
PAL NTSC
IN
PHONO
IN OUT
FM 50kHz 100kHz
/50 S
/75 S VCR2 OUT
AM 9kHz 10kHz
REC
STEP IN
CHANNEL 1
/FM DE- EMPHASIS
TAPE2
MONI-
TOR OUT
FM VCR1
PLAY
BAL
300 REC
IN
TAPE1
FM
LD
UNBAL
IN
75 PLAY
TV
GND
CD
IN
/SAT
IN
R L R L VIDEO
AM
SEE INSTRUCTION MANUAL
LOOP
ANTENA
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
ANTENNA
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
Illustration shows Multi-voltage model.
NOTE:
Before connecting the MAIN-REPEATER or MINI-REPEATER, switch power to the unit OFF, and wait
for about one hour. (When power is ON, the rear panel may become very hot.)
10
< >
ARB7050
CD
VCR
VCR
SYSTEM CONTROL
IR OUT
MAIN-
REPEATER
2
MINI-
REPEATER
S
OUT
S
IN
S
IN
TO
S
MONITOR
OUT
TV
1
2
VSX-D3S
NOTE:
To prevent possible damage, be careful to avoid accidentally
connecting the MINI-REPEATER to the MAIN-REPEATER
terminals.
1
2
1 Remove the seal.
2 Stick onto the remote control
1 Insert the REPEATER's two
pegs into the holes on the top.
2 Install the REPEATER laying
on its side on the top.
The pegs are usually
inserted in the two
rear holes.
Use the two front holes when
there's another component on
top of this preventing easy
r e c e p t i o n o f t h e M A I N
REPEATER's infrared signals.
VSX-D3S
sensor window.