Troubleshooting Guide - Panasonic DVD-F65 Operating Instructions Manual

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not
solve the problem, consult your dealer for instruction.
Power
No power.
The unit is automatically switched
to the standby mode.
Operation
No response when buttons
pressed.
No operations can be performed
with the remote control.
Play doesn't start (or stops
immediately) when you press
[1] (PLAY).
Cannot play DVDs.
Cannot select alternative
languages.
No menu play.
No subtitles.
Soundtrack and/or subtitle
language is not the one selected
with the SETUP menus.
Cannot change angle.
You have forgotten your ratings
password.
Reset all the settings to Factory
Preset.
The drawer stops while opening.
Picture
Picture distorted.
Menu not displayed correctly.
No picture.
The picture shown on the
television is not normal.
(The sides of the picture are cut
off, the picture is stretched
horizontally, or black bands
appear at the top and bottom of
the screen.)
There is ghosting when
progressive output is on.
Picture quality is poor.
The SETUP menus and other
screens shown on the television
are displayed incorrectly.
Colours appear faded.
18
≥Insert the AC mains lead securely into the household mains socket.
≥The unit automatically switches to standby after approximately 30 minutes in the stop mode. Turn the
power back to ON.
≥The SLEEP timer functioned.
≥Some operations may be prohibited by the disc.
≥The unit may not be operating properly due to lightning, static electricity or some other external factor.
Reset procedure:
Press [Í/I] to switch the unit to the standby mode and then back to ON.
Alternatively, press [Í/I] to switch the unit to the standby mode, disconnect the AC mains lead, and
then reconnect it.
≥Check that the batteries are installed correctly.
≥The batteries are depleted: Replace them with new ones.
≥Point the remote control at the remote control sensor and operate.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
≥This unit cannot play discs other than the ones listed in these operating instructions.
≥You can only play DVD-Video if their region number is "2", "ALL" or multiple region number including "2".
≥The disc may be dirty and may require cleaning.
≥Ensure that the disc is loaded with the label of the side to be played facing upwards.
≥Check that the DVD-RAM has something recorded on it.
≥Sequential Mode is on. Press [SEQUENTIAL] to turn Sequential Mode off.
≥This function depends on software availability.
≥Try selecting from the disc's menu if one is available.
≥This function depends on software availability.
≥This function depends on software availability.
≥Subtitles are cleared from the television. Turn on the subtitles.
≥Subtitle position is wrong. Adjust the position.
≥This function depends on software availability.
≥This function depends on software availability. Even if a disc has a number of angles recorded, these
angles may be recorded for specific scenes only.
≥While stopped, press and hold [:/6] and [;] on the unit and then also press and hold [<] on
the unit until "Initialized" disappears from the television. Turn the unit off and on again.
All settings will return to the default values.
≥There are more than 5 discs in the unit. Remove one or more discs and turn the unit off and on again.
≥Some distortion is normal during SEARCH.
≥Restore the zoom ratio to a1.00.
≥Set the subtitle position to 0.
≥Set 4:3 Aspect to "Normal".
≥Check the connection.
≥Make sure the television is on.
≥Ensure the television's video input setting (e.g., VIDEO 1) is correct.
≥Go to Video in the SETUP menus, and change "TV Aspect" to suit your television.
≥Use the television to change the aspect to the correct one.
If your television cannot change the aspect when input is progressive, try changing 4:3 Aspect
with the GUI screen.
≥Turn off the zooming feature of your television if you are using Variable Zoom.
≥Ensure that the unit is connected directly to the television, and is not connected through a video
cassette recorder.
≥Change Video output mode to "480I". This problem is caused by the editing method or material used
on DVD-Video, but should be corrected if you use interlace output.
≥Check the settings in the GUI screen's Picture Menu.
≥When you are using the component video out terminals to connect to a television
check to see if the "Video Out (AV/Component)" setting is set to "Y PB PR" in the SETUP menu.
≥The unit and television are using different video systems.
Use a multi-system or PAL television.
Page
4
–
9
–
–
3
3
3
–
6
Cover
6
7
–
8
–
7
–
–
12
12
–
–
–
–
–
11
12
15
4
–
–
5, 16
–
15
11
4
14
14
16
–