Specifications - Panasonic DVD-F65 Operating Instructions Manual

Sound
No sound.
Distorted sound.
Piercing noise comes from the
speakers.
Effects do not work.
Unit displays
"NOPLAY"
"CHECK"
"H∑∑"
∑∑ stands for a number.
Television displays
"Cannot display group xx, picture
xx."
"The progressive out is set to
"Disable""
No on-screen display or only
partially displayed.
The disc's menu is displayed in a
different language.

Specifications

Signal system:PAL 625/50, PAL525/60, NTSC
Operating temperature range: i5 to i35 oC
Operating humidity range:
5 to 90 % RH (no condensation)
Discs played (8 cm or 12 cm):
(1) DVD-RAM (DVD-VR compatible)
(2) DVD-Audio
(3) DVD-Video
(4) DVD-R (DVD-Video compatible)
(5) CD-Audio (CD-DA)
(6) Video CD
(7) SVCD (Conforming to IEC62107)
(8) CD-R/CD-RW
(CD-DA, Video-CD formatted discs)
(9) MP3/WMA
≥Maximum number of tracks and groups
recognizable: 999 tracks and 99
groups
≥Compatible compression rate:
MP3: between 32 kbps and 320 kbps
WMA: between 48 kbps and 192 kbps
(10) JPEG
≥Exif Ver 2.1 JPEG Baseline files
≥Maximum number of pictures and
groups recognizable:
3000 pictures and 300 groups
≥Picture resolution:
between 320t240 and 6144t
4096 pixels (Sub sampling is 4:2:2 or
4:2:0)
(11) HighMAT Level 2 (Audio and Image)
Video output:
Output level:
Output terminal: Pin jack (1 system)/AV
≥Check the connections.
≥Check the volume on the equipment you have connected.
≥Ensure that the input settings on the other equipment are correct.
≥Turn Advanced surround off if it causes distortion.
≥Output from this unit will be in stereo (two channels) when Advanced surround is on. Turn Advanced
surround off if you are using three or more speakers.
≥If the "D.MIX" indicator on the display goes out while playing a multi-channel DVD-Audio disc, sound
only comes from the front left and right speakers. Read the disc's instructions for details.
≥Press [1] (PLAY) to restore normal play after changing the speed.
≥Noise may occur when playing WMA files.
≥If you have connected this unit to other equipment through the DIGITAL AUDIO OUT terminal, ensure
you have selected the correct settings for "Dolby Digital", "DTS Digital Surround" and "MPEG" in the
SETUP menus' Audio menu.
≥Dialogue enhancer and Advanced surround do not work when the unit is outputting bitstream signals.
≥Advanced surround does not work if you have changed the play speed.
≥You inserted a disc the unit cannot play; insert one it can.
≥You inserted a blank DVD-RAM.
≥Disc is dirty: Wipe it clean.
≥Trouble may have occurred. The number following "H" depends on the status of the unit.
Reset procedure:
Press [Í/I] to switch the unit to the standby mode and then back to ON. Alternatively, press [Í/I] to
switch the unit to the standby mode, disconnect the AC mains lead, and then reconnect it.
≥If the service numbers fail to clear, note the service number and contact a qualified service person.
≥You are trying to display incompatible pictures.
≥Go to Video in the SETUP menus, and select "Enable (NTSC Disc Only)" in "Progressive Out
(Component)".
≥Go to Display in the SETUP menus, and select "On" for "On-Screen Messages".
≥Press [DISPLAY], and press [2, 1] to highlight the Bar Position icon, then press [3, 4] to adjust the
position.
≥Go to Disc in the SETUP menus, and select the preferred language for "Menus".
S-video output:
Y output level:
C output level: NTSC; 0.286 Vp-p (75 ≠)
Output terminal: S terminal (1 system)/AV
Component video output (NTSC: 480P/480I,
PAL: 576I):
Y output level:
P output level:
B
P output level:
R
Output terminal:
(1 system, Y: green, P
RGB video output:
R output level:
G output level:
B output level:
Output terminal:
Audio output:
Output level:
Output terminal:
Number of terminals: 2 channel:1 system
Audio performance:
(1) Frequency response:
≥DVD (linear audio):
≥DVD-Audio:
≥CD audio:
(2) S/N ratio:
≥CD audio:
(3) Dynamic range:
1 Vp-p (75 ≠) ≥DVD (linear audio):
≥CD audio:
1 Vp-p (75 ≠)
PAL; 0.300 Vp-p (75 ≠)
1 Vp-p (75 ≠)
0.7 Vp-p (75 ≠)
0.7 Vp-p (75 ≠)
Pin jack
: blue, P : red)
B R
0.7 Vp-p (75 ≠)
0.7 Vp-p (75 ≠)
0.7 Vp-p (75 ≠)
AV
2 Vrms (1 kHz, 0 dB)
Pin jack/AV
4 Hz–22 kHz (48 kHz sampling)
4 Hz–44 kHz (96 kHz sampling)
4 Hz–88 kHz (192 kHz sampling)
4 Hz–20 kHz
115 dB
102 dB
98 dB
(4) Total harmonic distortion:
≥CD audio:
Digital audio output:
Optical digital output: Optical terminal
Pickup:
Wave length: 658 nm/790 nm
Laser power: CLASS 2/CLASS 1
NORSK
Pickup:
Bølgelengde: 658 nm/790 nm
Laser-styrke:Ingen farlig strålning sendes ut
Power supply: AC 220–240 V, 50 Hz
Power consumption:
Dimensions: 430 (W)k405 (D)k59.7 (H) mm
Mass:
Power consumption in standby mode:
[Note]
Specifications are subject to change without
notice. Mass and dimensions are approximate.
Page
4, 5
–
–
15
15
–
15
–
17
–
15
6
–
6
–
–
10
16
16
13
16
0.0025 %
15 W
4.1 kg
approx. 2.8 W
19