Power Management; Display Driver - Panasonic Toughbook CF-71 Series Operating Instructions Manual

Reinstalling Software

Power management

27 Delete the check mark for [When powered by AC
power] and [When powered by batteries] in [Control
Panel] - [Power] - [Disk Drives], then press [OK].
Device manager 2
28 Add the check mark
- [System] - [Device Manager] - [CDROM] -
[MATSHITA UJDA150*] - [Settings].
Depending on the CD-ROM drive, there are cases
in which the check mark can not be added for
[DMA].
* If a CD-ROM drive other than CF-VCD711 (option) is used,
select the CD-ROM drive that will be used.
29 Set [L:] for [Reserved drive letters], then press [OK].
30 Add the check mark
ager] - [Disk drives] - [GENERIC IDE DISK TYPE**]
- [Settings], then press [OK].
31 Set [Mobile or docking system] in [Performance] - [File
System] - [Hard Disk] - [Typical role of this machine],
then press [OK].
32 At the [System Properties], press [Close]. The display
will ask you to restart Windows, then press [Yes].

Display driver

33 Select [Super VGA 1024 X 768] for [Models] in [Con-
trol Panel] - [Display] - [Settings] - [Advanced Prop-
erties] - [Monitor] - [Change], then press [OK].
34 Confirm that there is a check mark
cally detect Plug & Play monitors] in [Options] for the
[Monitor], and then press [Close].
35 Set [High Color (16 bit)] for the [Color palette], set
[800 by 600 pixels] for the [Desktop area] and then
press [OK].
If [Compatibility Warning] is displayed, select [Ap-
ply the settings without restarting?] and press [OK].
After that, select [OK] at the [Display Properties],
and select [YES] at the [Do you want to keep this
setting?].
If after a short period of time no action is taken for
the [Do you want to keep this setting?], the [Win-
dows has restored your original display settings]
will appear. Select [OK] and perform the display
settings again.
DMI Viewer setup
36 Insert the FIRSTAID CD.
37 In [Start] - [Run], input [L:\en\dmi\setup.exe], then
press [OK].
DMI Viewer setup will start automatically. The dis-
play will ask you to restart Windows; press [Finish].
Panasonic Hand Writing setup
38 Insert the FIRSTAID CD.
39 In [Start] - [Run], input [L:\en\writing\setup.exe], then
press [OK].
Panasonic Hand Writing Setup will start automatically.
Simply follow the on-screen instructions.
40 Insert the FIRSTAID FD.
41 In [Start] - [Run], input [a:\pupdate.bat], then press
[OK].
42 Click at the upper right corner to close the display.
22
for [DMA] in [Control Panel]
for [DMA] in [Device Man-
for [Automati-
Infrared
43 Select [Control Panel] - [Add New Hardware].
44 Press [Next] at the [Add New Hardware Wizard].
45 Select [No], then press [Next].
46 Select [Infrared] in [Hardware types] and press [Next].
47 Press [Next], and press [Next] again.
48 Select [Generic Ir Serial Port [COM2]] in [Select the
port that infrared device.....].
49 From here on, follow the instructions given on the
display followed by pressing [Next].
If the computer asks you to insert the Windows 95
Disk, press [OK]. Input [c:\cabs], then press [OK].
50 Press [Finish].
Installing Internet Explorer 4.0
Reinstalling Windows causes an older version of Internet Ex-
plorer to be installed.
To return the computer to the state it was in when you pur-
chased it, follow the steps below to install the newer version
of Internet Explorer.
1 Insert the Windows 95 CD-ROM included in the Win-
dows 95 System Pack.
2 In [Start] - [Run], input [L:\win95\ie4setup.exe], then press
[OK].
3 At the [Internet Explorer 4.0 Active Setup], press [Next].
4 Read the [License Agreement] and select [I accept the
agreement], then press [Next].
5 At the display for [Installation Option], by selecting
select [Full Installation] and then press [Next].
Follow the on-screen instructions.
When the message indicating the end of the installation
operation appears, select [OK].
If a display with the message [Setup was unable to close
all programs automatically.] appears, when there is a
program in operation, save all data and then select [OK].
6 The display will ask you to restart Windows, then press
[Yes].
Installing Acrobat
page 9, Step 8
Port Replicator (Option)
After reinstalling the software on the hard disk, different set-
tings are necessary when using the port replicator. For more
information, please refer to the operating instructions that
accompany the port replicator.
®
Reader 3.0
,