BARRIER FREE
CADET™ RIGHT HEIGHT 16-1/2"
PRESSURE-ASSISTED ELONGATED TOILET
❏
2377.100
• Vitreous china
• Low-consumption (1.6 gpf/6.0 Lpf)
• Bowl rim at 16-1/2"
• Elongated bowl
• Pressure-assisted siphon jet flush action
• Fully-glazed 2" ballpass trapway
• 10" x 12" water surface area
• Close-coupled Flushometer tank*
• Side-mounted chrome trip lever
• Speed Connect
tank/bowl coupling system
®
• Sanitary dam on bowl
• Two bolt caps
• 100% factory flush tested
❏
3109.016 Bowl with two bolt caps
❏
4098.100 Tank complete with
coupling components
Nominal Dimensions:
806 x 495 x 800mm
(31-3/4" x 19-1/2" x 31-1/2")
Fixture only, seat and supply by others
Recommended working pressure range
20 psi - 80 psi
Alternate Configurations Available:
❏
3109.456 Elongated bowl only with slotted
rim for bedpan holding
❏
4098.700 Tank and tank cover only with tank
cover locking device
❏
4098.800 Tank and tank cover only with right
hand trip lever
❏
4098.900 Tank complete with right hand trip
lever and tank cover locking device
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige
❏ Seat: American Standard #5324.019 "Rise and
Shine" (with easy to clean lift-off hinge system)
solid plastic closed front seat with cover.
❏ Seat: American Standard #5311.012 "Laurel"
molded closed front seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate
© 2008 AS America Inc.
CADET™ RIGHT HEIGHT 16-1/2" HEIGHT
❏ Black
Div. of Sloan Valve Co
®
PRESSURE-ASSISTED EL TOILET
FINISHED WALL
31-3/4
(806mm)
3/4 ± 1/4
(19mm ± 6mm)
8-7/8
(225mm)
18-1/2
(470mm)
C/L OF SEAT POST HOLES
5-1/2 (140mm CENTERS)
5/8
(16mm)
13-3/8
5-3/4
(340mm)
(146mm)
12
(305mm)
C/L OF OUTLET
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION
OF 305mm (12") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
M45
VITREOUS CHINA
19-1/2
(495mm)
SUPPLY
AS
REQ'D
16-1/2
(419mm)
15
*
10
(381mm)
(254mm)
*
6
(152mm)
FINISHED
FLOOR
10
(254mm)
Revised 2/08
31-1/2
(800mm)