Table of Contents
Advertisement
Available languages
Available languages
Copying Your Tapes (Dubbing)
Connection
(Rear connection shown.)
VCR
(HiFi)
R
R
L
AUDIO OUT
VIDEO OUT
VCR
(Mono)
R
AUDIO OUT
VIDEO OUT
1
Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.
To monitor the dubbing, also connect a TV as shown.
2
PV-V4522-K : Connect AUDIO L/R OUT jacks on Playing VCR to AUDIO L/R IN jacks on
PV-V4022-K : Connect AUDIO OUT jack on Playing VCR to AUDIO IN jack on Recording VCR.
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit's Audio/Video outputs to the Recording VCR.
Playing (Source) VCR
1
Insert pre-recorded tape.
2
3
Press PLAY, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
4
Press PLAY to start dubbing.
Playing VCR starts playback.
5
Press STOP to stop dubbing.
To Monitor Dubbing on Your TV
1
Turn your TV on and tune to the
Recording VCR channel (CH3 or CH4).
2
Set the VCR/ TV Selector on the
Recording VCR to "VCR."
Note
• Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.
Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684
Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 238-2181
Calgary: 6835 8th Street N.E., Calgary, Alberta T2E 7H7 (403) 295-3922
Panasonic Canada Inc.
Vancouver: 12111 Riverside Way, Richmond, BC V6W 1K8 (604) 278-4211
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
Caution :
Unauthorized exchanging and/or copying of copyrighted recordings may be
K
Printed in Indonesia
(905) 624-5010
copyright infringement.
LSQT0537B
www.panasonic.ca
S1201-1052
- 8 -
LSQT0537B(Advanced Operations-English) - Front
Special VCR Features
Tape Position Display Feature
To find out the present tape position.
Tape position is displayed for VHS-C type
Cassettes, tapes under 30 minute long, and
VCR
IN FROM ANT.
TV
some other tapes, but the position is not
(HiFi)
VIDEO IN 2
L-AUDIO IN2-R
OUT TO TV
Front of VCR
correct.
R
L
(Front Audio L/R Video IN jacks are
1
also provided)
Press TAPE POSITION
R
L
AUDIO IN
to detect tape position.
For Model PV-V4522-K only
VIDEO IN
VHF/UHF
• "DETECTING TAPE
DETECTING TAPE POSITION
POSITION" only
appears the first time
a cassette is inserted
IN FROM ANT.
and it takes several
VCR
TV
(Mono)
VIDEO IN 2 AUDIO IN 2
seconds for correct
OUT TO TV
Front of VCR
indication to appear.
R
L
(Front Audio/Video IN jacks are
• The present tape
also provided)
position indication is
For Model PV-V4022-K only
BEG I N
END
displayed.
AUDIO IN
VHF/UHF
VIDEO IN
2
Press TAPE POSITION
to return to normal screen.
Remote Warning ON/OFF Feature
Recording VCR.
If Multi-brand feature is used (pages 2, 3), and
this feature is set to on, a warning appears
whenever an invalid key is pressed in TV mode
(PV-V4022-K) [TV, DSS or Cable mode (PV-
V4522-K)].
Recording (Editing) VCR
1
Press ACTION to display menu.
2
Press
to select
Insert blank tape with record tab.
VCR
CLOCK
CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING
:ON
REMOTE WARNING
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
and press
VCR' S OUTPUT CH
:3
or OFF.
Press INPUT* to set VCR Input mode to LINE1
SELECT :
SET :
EXIT
: ACT I ON
• If "OFF," remote
for Video Input (Rear) or to LINE2 for Video
warning will not appear
Input (Front). (See "Selecting the Input Mode"
if invalid key is pressed.
below.)
3
Press ACTION to return to normal screen.
Press REC, then PAUSE/SLOW
immediately to enter REC/PAUSE mode.
Auto Shut-Off Feature
The operation of steps 4 and 5 must be done on the playing
and recording VCRs at the same time.
The power shuts off at a preset time.
Press PAUSE/SLOW to start dubbing.
1
Press ACTION to display menu.
Recording VCR starts recording.
2
VCR
CLOCK
CHANNEL
Press
to select
REPEAT PLAY
:OFF
REMOTE WARNING
:ON
AUTO SHUT-OFF.
AUTO SHUT- OFF
:OFF
Press STOP to stop dubbing.
IDIOMA/LANGUE : ENGLISH
Press
repeatedly to
VCR' S OUTPUT CH
:3
change shut-off time as
SELECT :
SET :
shown below.
EXIT
: ACT I ON
Selecting the Input Mode
Method 1:
OFF
Press INPUT repeatedly.
Channel Number ↔ ↔ ↔ ↔ ↔ LINE1 ↔ ↔ ↔ ↔ ↔ LINE2
2 Hours
Method 2:
Press CH
/
.
4 Hours
Display will change as below.
1
2
3
6 Hours
(CABLE)
(TV)
LINE2
LINE1
125
or
69
3
• "L1" or "L2" lights on Multi-Function Display
Press ACTION to return to normal screen.
(about 4 sec.) when LINE1 or LINE2 is
selected.
Note
• The shut-off countdown will not
• LINE1: For rear audio/video connection.
function during Play or Record.
LINE2: For front audio/video connection.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 9 -
On-Screen Displays (OSD)
Weak Signal Display ON/OFF Feature
On-Screen Displays (OSD)
When set to "ON," picture is displayed
Function & Channel Displays
Blank Tape/
regardless of signal strength.
No Video Signal Indications
When a function button
CH 0 8
1
When blank tape is detected during play,
is pressed, e.g. PLAY, or
Press ACTION to display menu.
you change channels,
or the current channel has no signal (with
VCR
CLOCK
CHANNEL
a 5 second display
Weak Signal Display feature (p. 10) set to
REPEAT PLAY
:OFF
REMOTE WARNING
:ON
appears.
OFF), the TV screen will turn solid blue.
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH
:3
VCR Status & Clock Displays
SELECT :
EXIT
: ACT I ON
To display or remove
Function Status
overlay at right,
2
Press
to select
VCR
CLOCK
CHANNEL
➛ press DISPLAY*.
Rec Time Remaining
ANTENNA : CABLE
and display CHANNEL.
AUTO SET
(OTR mode only.
WEAK SIGNAL DISPLAY : OFF
Press
to select
See p. 5 of Basic
WEAK SIGNAL
Operations book.)
DISPLAY, and press
SELECT :
SET :
EXIT
: ACT I ON
to set ON or OFF.
Broadcast Audio
Being Received
• ON: Picture is displayed despite signal
(For Model PV-V4522-K only)
condition and may be of poor quality.
OFF: Screen turns solid blue when signal
Warning and Instruction Displays
is weak or non-existent.
• Selecting ON has no effect on connected
equipment with blue back feature.
OSD
Caution
3
Press ACTION to return to normal screen.
PLEASE SET CLOCK BY
If you attempt to set or review a Timer
PRESSING ACTION KEY
Recording and the Clock is not set...
VCR Lock Feature
When set to ON, all operations except for timer
TURN VCR OFF
After a Timer Program has been set...
record and tape eject are prohibited. Useful for
FOR TIMER RECORDING
households with small children.
To turn on, hold down
REC on the VCR in Stop
to set ON
VCR LOCK ACT I VATED
mode with no tape
If you press REC on the remote
CHECK CASSETTE
inserted for 7 sec.
control or VCR, and a cassette is
RECORD TAB
(Please ignore the NO
inserted with no record tab...
CASSETTE warning.)
To turn off, repeat above.
VCR LOCK OFF
If you press PLAY, FF, REW, or REC
NO CASSETTE
on the remote control or VCR without
a cassette inserted...
• VCR Lock cancels in 24 hours if clock is set.
TO CANCEL TIMER REC
If you press POWER or STOP during
PRESS POWER THEN
a Timer Recording...
STOP KEY
(visible in VCR mode only)
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
If head cleaning becomes necessary
CLEANING CASSETTE
while playing back a tape...
REC
OR REFER TO MANUAL
END
:PLAY
If you press a function button other
VCR LOCK ACTIVATED
than STOP/EJECT or POWER while
the VCR is in VCR Lock mode...
REMOTE CONTROL IS SET
If you press an invalid key on the
TO CABLE/DSS MODE
remote while in CABLE/DSS mode...
(For Model PV-V4522-K only)
USE VCR : VCR KEY
REMOTE CONTROL IS SET
If you press an invalid key on the
TO TV MODE
remote while in TV mode...
USE VCR : VCR KEY
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 10 -
- 11 -
Before Requesting Service
Check the following points once again if you are having trouble with your VCR.
(BO : refers to "Basic Operations" Instruction book.)
(AO : refers to "Advanced Operations" Instruction book.)
Power
Correction
• Completely insert Power Plug into an AC outlet.
No power...
• Set POWER button to on.
• Make sure power source is active.
Recording & Playback
Correction
TV program cannot be recorded...
• Check connections between VCR, external antenna,
and TV.
Current Time
Channel
• Check connections selection. (BO p. 4, AO p. 4)
• Make sure your antenna system (CABLE or TV) is
REC
1 2 : 0 0AM
CH 02
0 : 25
-0 : 1 2 : 3 4
Counter
correctly set. (Channels [BO p. 11])
STEREO
SP
SAP
• Make sure cassette record tab is intact. (BO p. 3)
MONO
Timer recording cannot be
• Confirm that clock is set to current time and date.
performed...
• Make sure Cable/DSS box (if used) is left on and
Tape Speed
tuned to channel to be recorded.
(See p. 3 of Basic
• Set recording start/stop times correctly. (BO p. 6)
Operations book.)
• Make sure VCR POWER button is pressed off. (BO p. 6)
• Timer recording may not be performed or continued if
These displays will alert you to a missed
a power interruption occurs before or during a Timer
operation or provide further instructions.
Recording, even after power is restored.
There is no playback picture, or the
• Select channel 3 or 4 on TV to match VCR output
Page
channel (3 or 4) (BO p. 4) or select LINE.
playback picture is noisy or contains
streaks...
• Set VCR/TV selector to "VCR."
• Adjust TRACKING control in either direction. (BO p. 3)
See page 6 of
• Try Head Cleaning. (BO p. 3)
Basic Operations
book
During special effects playback,
• Set TV's Vertical Hold Control to MANUAL, then
picture may contain some vertical
adjust.
jitter when using a TV with an
Automatic Vertical Hold Control...
See page 6 of
VCR cannot be controlled...
• Make sure VCR power is on.
Basic Operations
• Check Remote batteries.
book
• Make sure VCR LOCK is set to off. (AO p. 10)
• Make sure Remote is in proper mode. (AO p. 2, 3)
• Make sure Timer Record is not in progress.
See page 3 of
Remote Control
Correction
Basic Operations
VCR cannot be remote controlled...
• Make sure VCR power is on.
book
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on
VCR. (BO p. 10)
• Avoid any object blocking signal path.
See page 5 of
• Check Remote batteries. (BO p. 3)
Basic Operations
• Make sure VCR LOCK is set to off. (AO p. 10)
book
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
ACTION and PROG buttons do not
• Check connections between VCR, external antenna,
respond...
and TV.
See page 6 of
• Press VCR button for VCR mode. (AO p. 2, 3)
Basic Operations
• Check Remote batteries. (BO p. 3)
book
Miscellaneous
Correction
Programs cannot be viewed on TV...
• Make sure TV power is on.
See page 3 of
• Make sure TV is set to output of VCR.
Basic Operations
• Check connections between VCR, external antenna,
book
and TV.
• Set VCR/TV selector to "TV." (BO p. 5)
• Make sure proper signal source is selected.
• Insert the cassette with window side up; record tab
Video cassette cannot be inserted...
facing you.
• Check if a tape is already in the unit.
See page 10
Video cassette cannot be removed...
• Completely insert Power Plug into an AC outlet.
Video cassette ejects when a
• Make sure cassette record tab is intact. (BO p. 3)
recording is started or the power is
turned off for timer recording...
In Stop mode, the motor
• To enable Quick play mechanism, the cylinder will
See pages 2, 3, 10
(CYLINDER) continues to rotate...
rotate for about 3 minutes. This reduces response
time from Stop to Play mode and from Play to Rewind
Search mode.
See pages 2, 3, 10
- 12 -
Video Cassette Recorder
Operating Instructions
(Advanced Operations)
For Basic operations, see the separate
"Basic Operations" instruction book.
PV-V4022-K / PV-V4522-K
Models No.
Table of Contents
Multi-Brand Control Feature .................................. 2,3
Advanced Connections (Cable/DSS) ....................... 4
MTS Broadcast / VHS Hi-Fi Stereo System
(
For Model PV-V4522-K only
) ..................................... 5
Tape Operation .................................................... 6, 7
Copying Your Tapes (Dubbing) ................................ 9
Special VCR Features ............................................ 10
On-Screen Displays (OSD) .................................... 11
Before Requesting Service .................................... 12
As an
E
NERGY
S
TAR Partner, Panasonic
has determined that this product or product
E
S
model meets the
NERGY
TAR guidelines
for energy efficiency.
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
LSQT0537B
Advertisement
Table of Contents
