Panasonic PV-V4022-A Operating Instructions page 4

Multi-Brand Control Feature Advanced Connections
Multi-Brand Control Setup Audio/Video connection
The Remote Control can be set to control some TV functions. If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.
1
Find your TV Brand Code Number from those shown below.
2
Set up for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
3
Confirm code entry,
➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.
Notes • Repeat setup after remote battery replacement.
• Remote will not control every TV made by the manufacturer listed. If you get no
response, your particular unit cannot be controlled. There are NO additional codes for
the products listed. If your product is not listed, then the remote is not compatible with
that product.
Using Multi-Brand Control
1
Connect the VCR's VIDEO OUT jack to the TV's VIDEO IN jack.
After remote is set up, you can select VCR or TV for the desired function.
Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)
Unit
VCR TV 2
Mode
Connect VCR's AUDIO OUT jack to the TV's AUDIO IN jack.
VCR All VOL UP/DOWN
VCR/TV, PLAY, STOP, EJECT, DISPLAY, FF, REW, POWER, INPUT, ENTER,
TV PAUSE/SLOW, REC, SPEED, CM/ZERO, RESET NUMBER keys, CH UP/DOWN,
COUNTER, TAPE POSITION
VOL UP/DOWN 3
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to "VIDEO."
Notes
• Not all functions listed may be controllable.
• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel
selection.
I I I I I With a Cable Box (VCR
TV Brand Code Numbers
Panasonic ....................... 01, 02 Sylvania ................................. 05 JVC ....................................... 11
Quasar ............................ 01, 02 Sharp ............................... 06, 07 Hitachi ................................... 12 ANT
AUDIO
RCA ...................................... 03 Sony ...................................... 08 Mitsubishi ........................ 07, 13 or
GE ......................................... 03 Toshiba ................................. 09 Samsung ............................... 14
CATV
Zenith .................................... 04 Sanyo .................................... 10 Gold Star ................... 15, 16, 17 VIDEO
Magnavox .............................. 05 Fisher .................................... 10
IN 1 OUT
Important Notes
• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one
listed.
• Some TV brands require you to turn on the power manually.
I I I I I Connect With Two Cable Boxes
CABLE BOX
IN OUT
ANT
or 2-Way Splitter
CATV
OUT 1 OUT 2
- 2 -
PV4022-A Advanced-2 (030107).p65 3
LSQT0699A (Advanced Operations) - Back
On-Screen Displays (OSD)
Function & Channel Displays
When a function button is
CH 0 8
pressed, e.g. PLAY, or you
change channels, a 5 second
display appears.
IN FROM ANT.
VCR
TV
AUDIO OUT
R
AUDIO IN
VHF/UHF
OUT TO TV
Blank Tape/No Video Signal Indications
VIDEO OUT When blank tape is detected during play, or the
current channel has no signal (with Weak Signal
VIDEO IN Display feature (p. 10) set to OFF), the TV screen
will turn solid blue.
VCR Status & Clock Displays
To display or remove overlay at right,
➛ press DISPLAY*.
Function Status
Rec Time Remaining
(OTR mode only. See p. 5
of Basic Operations book.)
Cable Box)
You Can You Cannot
TV
• view any • record
(including scrambled
IN FROM ANT.
IN OUT channels.
R scrambled)
R
CABLE BOX channel.
AUDIO
L L
VHF/UHF
OUT TO TV IN OUT VIDEO
• use VCR
VHF/UHF Remote
Control to
VCR
select
channels
without using
Multi-brand
control feature.
You Can You Cannot
VCR
• record and view • view a
channel
both scrambled
AUDIO IN FROM ANT.
other than
and
R
unscrambled the one
L VHF/UHF selected for
channels if
VIDEO
OUT TO TV any type of
additional
TV equipment is recording.
IN 1 OUT
added.
IN OUT • do a Timer
A/B Switch This connection
R
CABLE BOX requires: two recording of
AUDIO
L a channel
converter
IN OUT IN 1 IN 2
VIDEO boxes, an A/B unless you
VHF/UHF switch, and a 2- select it at
the cable
way splitter.
box.
- 3 -
Warning and Instruction Displays
These displays will alert you to a missed operation or provide further instructions.
OSD Caution
If you attempt to set or review a Timer
PLEASE SET CLOCK BY
PRESSING ACTION KEY Recording and the Clock is not set...
TURN VCR OFF After a Timer Program has been set...
FOR TIMER RECORDING
If you press REC on the remote
CHECK CASSETTE
control or VCR, and a cassette is
RECORD TAB
inserted with no record tab...
If you press PLAY, FF, REW, or REC
NO CASSETTE
on the remote control or VCR without
a cassette inserted...
TO CANCEL TIMER REC If you press POWER or STOP during
PRESS POWER THEN a Timer Recording...
STOP KEY
Current Time (visible in VCR mode only)
Channel
VIDEO HEADS MAY
NEED CLEANING
REC 1 2 : 0 0AM CH 02
Counter
0 : 25 -0 : 1 2 : 3 4 PLEASE INSERT HEAD If head cleaning becomes necessary
SP
CLEANING CASSETTE
while playing back a tape...
OR REFER TO MANUAL
Tape Speed
END :PLAY
(See p. 3 of Basic
Operations book.)
If you press a function button other
VCR LOCK ACTIVATED
than STOP/EJECT or POWER while
the VCR is in VCR Lock mode...
REMOTE CONTROL IS SET If you press an invalid key on the
TO TV MODE
remote while in TV mode...
USE VCR : VCR KEY
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 4 - - 5 -
2003/01/08, 16:52
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
Page
information are also included for timer recordings. These marks are used to access or
scan recordings.
See page 6 of
Basic Operations Index Search Program End Search
book
Locates end point of recording for continuity.
1 SEARCH Press SEARCH* to
INDEX PROGRAM END
display SEARCH in Stop
1
ENTER INDEX NUMBER :1
USING 1- 9 KEYS or Play mode, and then Press SEARCH twice to display SEARCH
press NUMBER keys to
See page 6 of FORWARD SEARCH :FF in Stop or Play mode.
REVERSE SEARCH :REW
Basic Operations NEXT :SEARCH select recording
EXIT :STOP
number. 2 Press FF
book SEARCH
INDEX PROGRAM END
to start PROGRAM
• To calculate number,
END SEARCH.
see below.
SEARCH START :FF
• To cancel, press
Press FF or REW
STOP or PLAY.
See page 3 of
to start search. EXIT :SEARCH
Basic Operations
book
2 Play begins at search
INDEX SEARCH Examples of Program End Search.
end. To search forward
or back 1 index, press
Fig. 1
FF or REW while
See page 5 of
screen left is displayed Program 1 Program 2 or BLANK
FORWARD SEARCH :FF
Basic Operations REVERSE SEARCH :REW
(10 sec.). the current tape position
book Press SEARCH button
End Point
FF
• To cancel, press
STOP or PLAY.
Fig. 2
See page 6 of
Program 1 BLANK Program 2 BLANK
Basic Operations
the current tape position
Press SEARCH button
book
End Point
FF
To Calculate Index Number
Fig. 3
the current tape position
Example 1: Press SEARCH button
See page 3 of
Basic Operations To go to rec. 2 from rec. 4, enter 3 and press
Program 1 BLANK Program 2
book REW.
If search
FF
exceeds a few
End Point
seconds in
BLANK area.
1 2 3 4 5 6 7
Upon locating end point,
See page 10
➛ search continues 7 sec. past end point,
Example 2:
➛ tape rewinds to 10 sec. before end point,
To go to rec. 6 from rec. 2, enter 4 and press
➛ tape plays to end point and stops.
FF.
See pages 2, 10 Notes
1 2 3 4 5 6 7 • If Program End Search is started very
close to an index mark, that mark may be
skipped over.
NOTE: indicates start points of each recording.
• To cancel, press PLAY or STOP.
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
- 6 -
Tape Operation
Repeat Play Commercial Skip
Set to playback a recording over and over. VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1
Press ACTION to display menu.
1
Press CM/ZERO in Play mode.
2 Press
VCR CLOCK CHANNEL • Press CM/ZERO repeatedly to change
REPEAT PLAY :OFF
to select REPEAT PLAY
REMOTE WARNING :ON
skip time as shown below.
AUTO SHUT- OFF :OFF
and press to set ON
AUTO VCR/TV :ON
IDIOMA/LANGUE : ENGLISH
or OFF.
VCR' S OUTPUT CH :3
SELECT : SET : ON : Play repeats at
EXIT : ACT I ON
tape end or if
PLAY
unrecorded portion
over 30 sec. is
detected.
1st Press 1 min Skip
3
Press ACTION to return to normal screen. 2nd Press 2 min Skip
3rd Press 3 min Skip
Zero Search
• No indication appears.
To quickly return to a specified tape location.
1
Press DISPLAY during play
to display Counter.
2 Press RESET
PLAY 1 2 : 0 0AM
0 : 0 0 : 0 0
COUNTER at desired
SP
position to reset to
"0:00:00".
3
Continue to record, playback, etc.
4
Press STOP.
5 Press CM/ZERO in Stop
REW 1 2 : 3 0AM CH 02
0 : 30 : 30
mode to start ZERO
SP
SEARCH.
• Unit will go into FF or
REW mode and stop at
the last point the
Counter was set to
0:00:00.
STOP 1 2 : 3 1AM CH 02
0 : 0 0 : 0 0
SP
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 7 -