Panasonic PV-V4022-A Operating Instructions page 2

Before Using
Important Safeguards and Precautions
Congratulations
FOR YOUR SAFETY, READ AND RETAIN OUTDOOR ANTENNA INSTALLATION
on your new purchase! With proper use, this
ALL SAFETY AND OPERATING 1 SAFE ANTENNA AND CABLE CONNECTION dependable product will provide years of
If an outside antenna or cable system is connected to the
INSTRUCTIONS. HEED ALL WARNINGS IN
enjoyment. Please fill in the information below.
equipment, be sure the antenna or cable system is grounded
THE MANUAL AND ON THE UNIT
so as to provide some protection against built up static (Serial number is on tag on back of VCR.)
charges and voltage surges.
INSTALLATION
Section 810 of the National NEC - NATIONAL • Date of Purchase
ELECTRICAL CODE
1 POWER SOURCE CAUTION Electrical Code, ANSI/NFPA ANTENNA
LEAD IN WIRE
Operate only from a power source indicated on
70 (in Canada, part 1 of the GROUND • Dealer Purchased From
CLAMP
the unit or in this manual. If necessary, have
Canadian Electrical Code) ANTENNA
DISCHARGE UNIT • Dealer Address
your Electric Utility Service Company or Video provides information with (NEC SECTION 810-20)
ELECTRIC
Products Dealer verify the power source in your SERVICE GROUNDING CONDUCTORS
respect to proper grounding EQUIPMENT (NEC SECTION 810-21)
• Dealer Phone No.
home. GROUND CLAMPS
of the mast and supporting
2 POLARIZED OR GROUNDING PLUG structure, grounding of the POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250, PART H) • Model No.
As a safety feature, this Video product comes lead-in wire to an antenna discharge unit, size
with either a polarized power cord plug (one of grounding conductors, location of antenna discharge unit,
• Serial No.
blade is wider than the other), or a three-wire connection to grounding electrodes and requirements for the
grounding type plug. grounding electrode.
Accessories
POLARIZED PLUG CAUTION: 2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER
This plug will only fit into an outlet one way. If you LINES OR CIRCUITS
An outside antenna system should be located well away
cannot fully insert the plug, try reversing it. If it still Remote Control
will not fit, have an electrician install the proper wall from power lines, electric light or power circuits and where it
LSSQ0263
outlet. Do not defeat the safety feature by tampering will never come into contact with these power sources if it
should happen to fall. When installing an outside antenna,
with the plug.
extreme care should be taken to avoid touching power lines,
GROUNDING PLUG CAUTION:
circuits or other power sources as this could be fatal.
This plug will only fit into a three-hole grounding
Because of the hazards involved, antenna installation should
outlet. If necessary, have an electrician install the
be left to a professional.
proper outlet. Do not defeat the safety feature by
tampering with the plug. USING THE VIDEO UNIT
3 POWER CORD If the unit has been in storage or moved to a new location, refer
first to the INSTALLATION section of these safeguards.
Make sure power cords are routed so that they
are not likely to have anything rest on them, roll 1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR
over them, or be in the way of walking traffic. MOISTURE OF ANY KIND.
If an extension cord is used, make sure it also 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
has either a polarized or grounded plug and that
STRONG IMPACT, unplug the unit and have it inspected by
the cords can be securely connected. Frayed a qualified service technician before use.
cords, damaged plugs, and damaged or cracked 3 DURING AN ELECTRICAL STORM
wire insulation are hazardous and should be
During a lightning storm, whether indoors or outdoors, or
replaced by a qualified service technician.
before leaving the unit unused for extended periods of time,
Overloaded outlets and extension cords are fire
disconnect all equipment from the power source as well as
hazards and should be avoided.
the antenna and cable system.
4 DO NOT BLOCK VENTILATION HOLES
4 WHEN THE UNIT IS PLUGGED IN
Ventilation openings in the cabinet release heat
• Never expose the unit to rain or water. DO NOT
generated during operation. If they are blocked, OPERATE if liquid has been spilled into the unit. To order accessories, call toll free
heat build-up inside the unit can cause failures
Immediately unplug the unit, and have it inspected by a 1-800-332-5368.
that may result in a fire hazard or heat damage
service technician. Fire and shock hazards can result from
to cassettes. For protection, follow these rules:
electrical shorts caused by liquid contact inside.
a. Never cover ventilation slots or the unit while Loading the Batteries
• Never drop or push any object through openings in the
in use, or operate the unit when placed on a
unit. Some internal parts carry hazardous voltages and
bed, sofa, rug, or other soft surface.
contact can cause electric shock or fire hazard.
b. Avoid built-in installation, such as a book
• Avoid placing the unit directly above or below your TV set
case or rack, unless proper ventilation is as this may cause electrical interference. Keep all
provided.
magnets away from electronic equipment.
5 AVOID EXTREMELY HOT LOCATIONS OR 5 USING ACCESSORIES
SUDDEN TEMPERATURE CHANGES
Use only accessories recommended by the manufacturer to
Do not place the unit over or near any kind of
avoid risk of fire, shock, or other hazards.
heater or radiator, in direct sunlight, inside a
6 CLEANING THE UNIT
closed vehicle, etc.. Do not move the unit
Unplug the unit. Then, use a clean, dry, chemically
suddenly between areas of extreme temperature
untreated cloth to gently remove dust or debris. DO NOT
variation. If the unit is suddenly moved from a
USE cleaning fluids, aerosols, or forced air that could over-
cold place to a warm place, moisture may
spray, or seep into the unit and cause electrical shock. Any
condense in the unit and on the tape.
substance such as wax, adhesive tape, etc. may mar the
6 TO AVOID PERSONAL INJURY
cabinet surface. Exposure to greasy, humid, or dusty areas
• Do not place unsecured
may adversely affect internal parts.
equipment on a sloping
surface. SERVICE
• Do not place this unit on any
1 DO NOT SERVICE THIS PRODUCT YOURSELF
support that is not firm, level,
If, after carefully following the detailed operating instructions,
and adequately strong. The this Video product does not operate properly, do not attempt
unit could fall causing serious
to open or remove covers, or make any adjustments not
Battery replacement caution
injury to a child or adult and described in the manual. Unplug the unit and contact a
damage to the unit. qualified service technician. • Do not mix old and new batteries.
• An appliance and cart combination should be
2 IF REPLACEMENT PARTS ARE REQUIRED • Do not mix alkaline with manganese batteries.
moved with care. Quick stops, excessive force,
Make sure the service technician uses only parts specified
and uneven surfaces may cause the appliance
by the manufacturer, or those having the same safety
and cart combination to overturn. Prevent Accidental Tape Erasure
characteristics as the original parts. The use of unauthorized
• Carefully follow all operating instructions and
substitutes may result in fire, electric shock, or other
use the manufacturer's recommended
hazards.
Break off the tab to
accessories when operating this unit or
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY
connecting it to any other equipment. prevent recording.
CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacturer's service literature to ensure that
Safety Precautions
the video unit is in safe operating condition.
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
Record Tab
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement: Afin de prévenir tout risque d'incendie ou de chocs électriques, ne pas
exposer cet appareil à la pluie ou à une humidité excessive.
Screw driver
Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu'au fond. Record/Playback Time
This symbol warns the user that uninsulated
Only use tapes with the
CAUTION voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
RISK OF ELECTRIC SHOCK Type of Video Cassette
DO NOT OPEN it is dangerous to make any kind of contact Tape Speed
with any inside part of this unit.
Setting T60
This symbol alerts the user that important
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, SP
DO NOT REMOVE COVER (OR BACK) literature concerning the operation and 1 Hour
(Standard Play)
maintenance of this unit has been included.
NO USER-SERVICEABLE PARTS INSIDE
Therefore, it should be read carefully in order
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL LP
to avoid any problems. 2 Hours 4 Hours
(Long Play)
SLP
3 Hours 6 Hours
FCC Warning: Any unauthorized changes or modifications to this equipment would void the
(Super Long Play)
user's authority to operate.
- 2 -
PV4022-A Basic-2 (030107).p65 3
Connections / Initial Setup (Ready to Play)
Please make all cable or antenna connections before plugging into the AC
Head Cleaning
outlet.
Old or damaged tapes may clog heads.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
Video Head Clog Sensor
Connecting
Screen-right appears during
V I DEO HEADS MAY
play if clogging is detected. NEED CLEAN I NG For ANT./Cable ➛ ➛ ➛ ➛ ➛ VCR ➛ ➛ ➛ ➛ ➛ TV
PLEASE I NSERT HEAD
To remove screen, press CLEAN I NG CASSETTE
OR REFER TO MANUAL
PLAY. 1
Connect cable from
END : PLAY
• Use "dry" type head
Antenna/Cable to VCR's IN
cleaning cassette only.
FROM ANT. jack.
(Part No. NV-TCL30PT is recommended.)
PV-V4022-A
• Follow cleaning tape instructions carefully. 2 Connect VCR's OUT TO TV
Excessive use of tape can shorten head life.
jack to TV's ANT. IN jack
with included RF Cable
accessory.
Batteries 2 "AA" Cleaning the VCR For DSS/Cable Box ➛ ➛ ➛ ➛ ➛ VCR ➛ ➛ ➛ ➛ ➛ TV
Use soft, dry cloth or dusting attachment of a
1 Connect your cable box's
vacuum to remove dust from all cabinet vent
OUT jack to the VCR's IN
holes. You may moisten cloth with nonabrasive,
antistatic cleaner/ polisher. FROM ANT. jack with an RF
RF Coaxial Caution:
cable.
Cable
Alcohol and various solvents could damage finish.
2 Connect VCR's OUT TO TV
LSJA0372
jack to TV's ANT. IN jack
with included RF Cable
Specifications
accessory.
Power Source: 120 V AC, 60 Hz
Initial Setup (Ready to Play)
Power On
Power Consumption:
Approx. 18 W
1
Power Off Turn TV on and tune to channel 3.
Approx. 2.5 W 2
Plug VCR Power Cord into AC wall
Video Signal: EIA Standard NTSC color
outlet. VCR comes on and auto channel
Video Recording 4 rotary heads helical
and clock set starts.
System: scanning system
Audio Track: 1 track (Normal) • If screen below does not appear, check
VCR - TV connection and, if TV is
Tuner:
Broadcast Channels:VHF 2 ~ 13, UHF 14 ~ 69 tuned to channel 3, try switching it to
CABLE Channels: Midband A ~ I (14 ~ 22) channel 4.
Superband J ~ W (23 ~ 36)
• To change VCR's output channel,
Hyperband AA ~ EEE
please refer to "VCR's Output Channel"
(37 ~ 64)
in Advanced Operations book (p. 12).
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A
(01)
Ultraband 65 ~ 94, 100 ~ 125
Operating
Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 2.5 kg (5.5 lbs).
Plugging the AC Power Plug into an AC outlet
Dimensions: 360 (W) x 93 (H) x 242 (D) mm
14-3/16" (W) x 3-11/16" (H) x
9-9/16" (D) inch
Note: Designs and specifications are subject VCR CLOCK CHANNEL
to change without notice.
CH AUTO SET PROCEEDING
To record again
Features for a Quality Picture CANCEL : STOP
Digital Auto Picture
VCR CLOCK CHANNEL
Automatically controls the video output signal for
less noise depending on the tape condition.
AUTO CLOCK SET
Digital Auto Tracking
PROCEEDING
Continuously analyzes the signal and adjusts for
Cover the hole
optimum picture quality.
CANCEL : STOP
with cellophane
Manual Tracking Control
If you use a cable box, turn it on and set it
tape.
(to reduce picture noise)
to the Public Broadcasting Station (PBS)
Use during Playback and Slow Motion mode to
channel in your time zone. If you use a
reduce picture noise.
DSS receiver, it must be turned off.
Press CH (TRACKING) / on the remote
mark in this unit. control or on the VCR until the picture clears up.
Notes
To return to Auto Tracking, press POWER off,
then on again a few seconds later. • Function buttons are inoperative during Initial
Setup.
T120 T160
• To remove a cassette during Auto Set, press
2 Hours EJECT on the remote or STOP twice on the
2 Hours
40 Minutes VCR. In this case, settings must be made
manually. (See p. 12 of Advanced Operations
5 Hours
book.)
20 Minutes
• Depending on conditions, Auto Clock Set may
V-Lock Control (to reduce picture jitter)
take longer than 30 minutes. If so, press
8 Hours In Still mode, CH (TRACKING) / operate as a
STOP to stop setup and perform settings
V-Lock control.
manually. (See p. 12 of Advanced Operations
book.)
- 3 -
Playback / Record on a Tape
Playback a Tape Record on a Tape
1
1
Insert a tape . Insert a tape with a record tab (p. 3).
• Loose or peeling labels • VCR power comes on. "VCR" lights
may cause tape jam. on Multi Function Display.
• VCR power comes on. "VCR" lights
If Auto VCR/TV (see p. 10 of
on Multi Function Display. Advanced Operations book) is set to
VCR IN FROM ANT.
If Auto VCR/TV (see p. 10 of "OFF," press VCR/TV until "VCR"
TV
Advanced Operations book) is set to
lights on the Multi Function Display.
1
IN from "OFF," press VCR/TV until "VCR"
ANT./CABLE
lights on the Multi Function Display. 2
Press CH
to select the channel.
OUT TO TV
2
• For "LINE" input, see p. 9 of "Advanced
2 Press PLAY to play tape.
Operations" book.
• If tape has no rec. tab (p. 3), auto play begins.
VHF/UHF
• If recording from a channel over 100, first
press 100 key then the other 2 digits.
Special Features During Play
3
Forward/Reverse Scene Search Press SPEED
➛ Press FF or REW.
to select record speed (p. 3).
TV IN FROM ANT. Cable TV
VCR
Converter Box ➛ Press PLAY to release.
4
After search has begun, each additional Press REC
press of FF or REW changes speed as
to start recording.
IN from
shown below.
ANT./CABLE • To edit, press PAUSE/SLOW to pause,
1
OUT TO TV ↔
[SLP] : Approx. 21X Approx. 9X and again to resume recording.
↔
[LP] : Approx. 9X Approx. 7X
2
VHF/UHF ↔
[SP] : Approx. 7X Approx. 3X 5
Press STOP to stop recording.
If at 21X, 9X, or 7X speed the picture is
WARNING
interrupted, change speed to 9X, 7X, or 3X.
Over tightening "Nut type" RF coaxial cables
One Touch Recording
may damage jacks. Finger tighten only.
Notes
(recording in progress)
Press REC repeatedly to set length as follows:
3 • Picture interruption may occur with some TVs.
Settings are made automatically. ➛
• FF and REW search speed may vary 30 min. 1 hr.
➛ ➛
When setup is done, this screen depending on current tape position.
4:00 exit.
appears. The VCR shuts off at the length set.
Still (Freeze) Picture
VCR CLOCK CHANNEL ➛ Press PAUSE/SLOW. Record one station, watch another
6 /08 / 20 0 3 SUN 2 : 20PM
Press VCR/TV
➛ Press PLAY to release.
DST : ON
("VCR" goes out on Multi Function Display),
SETT I NG : CH 10
➛
select channels on TV (recording continues).
Frame by Frame Picture
AUTO CLOCK SET
➛ Press PAUSE/SLOW in Still mode.
COMPLETED
Select channels on VCR (in STOP or
➛ Press PLAY to release.
PAUSE mode)
Press VCR/TV
If "AUTO CLOCK SET IS INCOMPLETE"
Slow Motion Picture
("VCR" lights up on Multi Function Display),
appears, manually set clock. ➛ Hold down PAUSE/SLOW in Still mode.
➛
select channels on VCR.
See below. ➛ Press PLAY to release.
VCR CLOCK CHANNEL Notes
Notes
AUTO CLOCK SET IS
• Watching one channel and recording
INCOMPLETE • These features work best in SP or SLP mode.
another is not possible when using Cable
• The sound will be muted.
PLEASE SET CLOCK BY
Box or DSS Receiver.
PRESSING ACTION KEY • To reduce picture noise, see "Manual
• After 5 minutes in Pause mode, VCR stops
Tracking Control" on p. 3.
to protect the tape and the video heads.
• After VCR is in Still or Slow mode 3 minutes, it
auto switches to Stop mode to protect the tape
and the video heads.
Manual Clock Set
3
Press STOP to stop tape.
This video recorder, equipped with
If Auto Clock Set was incomplete.
Press REW or FF in Stop mode to
HQ (High Quality) system, is
1
Press ACTION* on remote to display Rewind or Fast Forward tape.
compatible with existing VHS
CLOCK menu. Press EJECT on remote, equipment. Only use tapes with the
or STOP/EJECT on VCR to eject tape.
mark. Only tapes tested and
VCR CLOCK CHANNEL
inspected for use in 2, 4, 6, and 8
1 / / :
hour machines are recommended.
DST:ON
SELECT MONTH
Auto Operation Functions
SELECT : SET :
EXIT : ACT I ON
Auto Play
2
Press to select the month and
➛ ➛
Insert a tape Power comes on Play starts if there is no record tab (see p. 3).
to set. In the same manner, select and
set the date, year, time, and DST Auto Rewind
(Daylight Saving Time). Play
➛ ➛
Tape end Rewind
Fast Forward
VCR CLOCK CHANNEL
Play Auto Eject
6 /08 / 20 0 3 SUN 2 : 20PM
(Repeat Play must be off)
DST:ON ➛ ➛ ➛
Play Tape end Rewind Tape ejects if there is no record tab
SET COMPLETED
SET :
START : ACT I ON
3
Press ACTION to start clock and exit.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 4 - - 5 -
2003/01/07, 14:22
Timer Recording
Timer Recording
1
1) Press PROG*.
2) Press to display program screen.
Example
2
1) Set record DATE,
TIMER PROG. LIST
DATE START STOP CH Today
13 SAT --:-- --:-- -- press to select:
TODAY 1~31= one time,
SLP
8 9 31 1
SELECT START DATE
or DAILY= MON~ FRI,
SELECT : SET:
END : PROG or WEEKLY= same time SELECT / Selection Order
7
or NUMBER keys
each week and press .
WEEKLY WEEKLY
2) Set remaining items, (SAT)
(MON)
press to select and
press to set START/ STOP times, CH (channel) or
LINE input (p. 9 of "Advanced Operations" book), and
tape speed (p. 3).
Press PROG to end programming.
3
To Enter More Programs
TIMER PROG. L I ST
DT START STOP CH SPD
Press to select and
13 2 : 00 P 3 : 20P 02 SLP
-- -- : -- -- : -- -- --
-- -- : -- -- : -- -- -- press to set an unused program.
-- -- : -- -- : -- -- --
Then repeat step 2.
CANCEL : ADD / DLT
SELECT : SET :
EXIT : PROG Or, press PROG to exit.
4
Press POWER off to set the timer recording. ("TIMER" lights on Multi Function Display.)
Review, Replace, or Clear Program Cancel a Timer Recording
➛ ➛ ➛
1:30 2:00 3:00 (Recording is not in progress) (Recording is in progress)
a
1) Press PROG. Press POWER and then STOP within 10
seconds to cancel the Timer Recording.
2) Press to select LIST.
(The TIMER indicator goes out on Multi
b Press to select
TIMER PROG. L I ST
Function Display.)
DT START STOP CH SPD desired program.
7 9 : 00A 12 : 00A 08 SP
8 10 : 00P 12 : 00P 02 SP
10 8 : 00P 9 : 00P 10 SP
SU 9 : 00P 10 : 00P L1 LP
CANCEL : ADD / DLT
SELECT : SET :
EXIT : PROG
c
To Replace program...
1) Press to display.
TIMER PROG. LIST
DATE START STOP
CH
7 SUN 9:00A 12:00A 08
2) Repeat Step 2
TODAY
(above) to set new
SP
SELECT START DATE
programs.
SELECT : SET:
END : PROG
or
To Clear program...
TIMER PROG. L I ST Press ADD/DLT.
DT START STOP CH SPD
-- -- : -- -- : -- -- --
8 10 : 00P 12 : 00P 02 SP
10 8 : 00P 9 : 00P 10 SP
SU 9 : 00P 10 : 00P L1 LP
CANCEL : ADD / DLT
SELECT : SET :
EXIT : PROG
d
Press PROG to end the programming.
Notes
• If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) must
be set to the Cable Box output channel and your Cable Box must be manually set to
the desired channel. The Cable Box must be left on.
• If a power interruption occurs while programming the timer, the timer program(s) may be
canceled. If "TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION" appears
on-screen, please re-enter the timer programs.
Important notes when using DSS receiver
• When recording programs via DSS receiver, DSS receiver must be left on.
• When recording programs via an antenna or cable, DSS receiver must be turned off.
- 6 -
Location of Controls
Remote Control Buttons
VCR (mode) TV (mode)
(Enables VCR functions) (Enables TV functions)
POWER DISPLAY
(Turns VCR off/on)
(Displays VCR status)
VCR/TV NUMBER Keys
2 6
(For TV or VCR mode) (Selects channel directly)
DAILY
INPUT
ADD/DELETE
(For LINE or channel) (Adds or deletes a channel)
WEEKLY
(SUN) SPEED
SEARCH/ ENTER
(Changes tape speed)
(Set search system /Tunes TV channel)
EJECT
PLAY (Plays a tape)/
(Ejects tape)
FAST FORWARD/SEARCH
(Fast forwards tape/ forward visual
COMMERCIAL SKIP/
ZERO SEARCH search)
Starts COMMERCIAL SKIP/ Zero Search REWIND/SEARCH
( )
(Rewinds tape/ reverse visual
ACTION
search)
(Displays menu)
STOP (Stops tape)
RECORD Remote keys
(Records a program, etc.)
PLAY, STOP, REW, and FF
function as
operation keys when menus
TAPE POSITION
are displayed.
(Locates tape position)
COUNTER RESET
(Resets counter to zero)
PROGRAM
(Displays Timer Program screen)
PAUSE/SLOW
(Displays still, frame by frame,
or slow motion picture)
VOLUME +/-
CHANNEL /
(Adjusts TV volume)
TRACKING/ V-LOCK
(Selects channel/ reduces
picture noise during Play and
Slow mode)
Remote Control
EJECT button: Press to eject tape. EJECT is not available during recording.
Front View of the VCR
Cassette Compartment
STOP/EJECT
POWER
PLAY
Video
Input
Connector
CHANNEL / Remote REWIND/
Audio Input RECORD FAST
Connector Sensor SEARCH FORWARD/
TRACKING/ V-LOCK
SEARCH
Multi Function Display
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 7 -