Panasonic PV-V4022-A Operating Instructions page 3

Copying Your Tapes (Dubbing)
Connection
(Rear connection shown.)
VCR
(Mono)
AUDIO OUT
Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.
1
To monitor the dubbing, also connect a TV as shown.
2
Connect AUDIO OUT jack on Playing VCR to AUDIO IN jack on Recording VCR.
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit's Audio/Video outputs to the Recording VCR.
Playing (Source) VCR
1
Insert pre-recorded tape.
2
3 Press PLAY, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
The operation of steps 4 and 5 must be done on both playing
and recording VCRs at the same time.
4 Press PLAY to start dubbing.
Playing VCR starts playback.
5
Press STOP to stop dubbing.
To Monitor Dubbing on Your TV
1
Turn your TV on and tune to the
Recording VCR channel (CH3 or CH4).
2
Set the VCR/ TV Selector on the
Recording VCR to "VCR."
Note • Dubbing tapes protected with Copy
Guard will have poor quality results.
Panasonic Consumer Electronics Company,
P Caution : Unauthorized exchanging and/or copying of copyrighted recordings may be
Division of Matsushita Electric Corporation of America
copyright infringement.
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company ("PSC"),
*Important: If a remote control button does not work when pressed,
Division of Matsushita Electric of Puerto Rico, Inc. Printed in Indonesia
Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, LSQT0699A
Carolina, Puerto Rico 00985
S0103-0
- 8 -
PV4022-A Advanced-1 (030107).p65 1
LSQT0699A (Advanced Operations) - Front
Special VCR Features
Remote Warning ON/OFF Feature
If Multi-brand feature is used (page 2), and this
feature is set to on, a warning appears
whenever an invalid key is pressed in TV mode.
IN FROM ANT.
VCR 1
TV Press ACTION to display menu.
(Mono)
OUT TO TV 2
VCR CLOCK CHANNEL Press to select
REPEAT PLAY : OFF
REMOTE WARNING
REMOTE WARNING : ON
R R AUTO SHUT- OFF : OFF
AUTO VCR/TV : ON and press to set ON
L
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH : 3 or OFF.
SELECT : SET :
EXIT : ACT I ON • If "OFF," remote
VIDEO OUT warning will not appear
if invalid key is pressed.
AUDIO IN
VHF/UHF
3
VIDEO IN
Press ACTION to return to normal screen.
VIDEO IN 2 AUDIO IN 2
Front of VCR
(Front Audio/Video IN jacks are also provided) Auto Shut-Off Feature
The power shuts off at a preset time.
1
Press ACTION to display menu.
2
VCR CLOCK CHANNEL Press to select
REPEAT PLAY : OFF
REMOTE WARNING : ON AUTO SHUT-OFF.
AUTO SHUT- OFF : OFF
AUTO VCR/TV : ON
Press repeatedly to
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH : 3
change shutoff time as
SELECT : SET : shown below.
EXIT : ACT I ON
Recording (Editing) VCR
Insert blank tape with record tab.
3
Press ACTION to return to normal screen.
Press INPUT* to set VCR Input mode to LINE1 Note • The shut-off countdown will not
for Video Input (Rear) or to LINE2 for Video function during Play or Record.
Input (Front). (See "Selecting the Input Mode"
below.)
Press REC, then PAUSE/SLOW
VCR/TV Selector Feature
immediately to enter REC/PAUSE mode.
The VCR/TV selection can be set to auto or
manual.
1
Press ACTION to display menu.
Press PAUSE/SLOW to start dubbing.
Recording VCR starts recording. 2 Press to select
VCR CLOCK CHANNEL
REPEAT PLAY : OFF AUTO VCR/TV,
REMOTE WARNING : ON
AUTO SHUT- OFF : OFF and press to set ON
AUTO VCR/TV : ON
IDIOMA/LANGUE : ENGLISH
or OFF.
VCR' S OUTPUT CH : 3
Press STOP to stop dubbing.
SELECT : SET :
EXIT : ACT I ON
• OFF(Manual): You select "VCR" or "TV"
Selecting the Input Mode
mode using the VCR/TV
button on the unit or remote.
Method 1:
Press INPUT repeatedly. • ON(Auto): "VCR" mode is automatically
Channel Number ↔ ↔ ↔ ↔ ↔ LINE1 ↔ ↔ ↔ ↔ ↔ LINE2 set when VCR is turned on,
or in Play mode.
Method 2:
3
Press CH / . Press ACTION to return to normal screen.
Display will change as below.
Note
1 2 3
(CABLE) • For more on VCR/TV selection, see "Record
(TV)
LINE2 LINE1 125 or 69 one station, watch another" and "Select
channels on VCR" sections (see p. 5 of Basic
• "L1" or "L2" lights on Multi-Function Display
Operations book).
(about 4 sec.) when LINE1 or LINE2 is
selected.
• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
press the VCR button on the remote and try the button again.
- 9 -
Before Requesting Service
Check the following points once again if you are having trouble with your VCR.
Tape Position Display Feature
(BO : refers to "Basic Operations" Instruction book.)
To find out the present tape position. (AO : refers to "Advanced Operations" Instruction book.)
Tape position is displayed for VHS-C
Power Correction
Cassettes type, tapes under 30 minutes, and
some other tapes, but the position is not
• Completely insert Power Plug into an AC outlet.
No power...
correct.
• Set POWER button to on.
• Make sure power source is active.
1
Press TAPE POSITION
to detect tape position. Recording & Playback Correction
TV program cannot be recorded... • Check connections between VCR, external antenna,
• "DETECTING TAPE
DETECTING TAPE POSITION
and TV.
POSITION" only
• Check connections selection. (BO p. 4, AO p. 3)
appears the first time
• Make sure your antenna system (CABLE or TV) is
a cassette is inserted
and it takes several correctly set. (Channels [AO p. 12])
• Make sure cassette record tab is intact. (BO p. 3)
seconds for correct
indication to appear.
Timer recording cannot be • Confirm that clock is set to current time and date.
performed... • Make sure Cable/DSS box (if used) is left on and tuned
• The present tape
to channel to be recorded.
position indication is
• Set recording start/stop times correctly. (BO p. 6)
BEG I N END displayed.
• Make sure VCR POWER button is pressed off. (BO p. 6)
2 • Timer recording may not be performed or continued if a
Press TAPE POSITION
power interruption occurs before or during a Timer
to return to normal screen.
Recording, even after power is restored.
There is no playback picture, or the • Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (BO p. 4) or select LINE.
playback picture is noisy or contains
streaks... • Set VCR/TV selector to "VCR."
• Adjust TRACKING control in either direction. (BO p. 3)
• Try Head Cleaning. (BO p. 3)
Weak Signal Display ON/OFF Feature
Special effects playback, picture
• Set TV's Vertical Hold Control to MANUAL, then adjust.
When set to "ON," picture is displayed
may contain some vertical jitter
regardless of signal strength.
when using a TV with an Automatic
Vertical Hold Control...
1
Press ACTION to display menu.
VCR cannot be controlled... • Make sure VCR power is on.
2 Press to select
VCR CLOCK CHANNEL • Check Remote batteries.
ANTENNA : CABLE
and display CHANNEL.
AUTO SET • Make sure VCR LOCK is set to off. (AO p. 10)
WEAK SIGNAL DISPLAY : OFF Press to select
• Make sure Timer Record is not in progress.
WEAK SIGNAL
DISPLAY, and press
SELECT : SET :
EXIT : ACT I ON to set ON or OFF. Remote Control Correction
VCR cannot be remote controlled... • Make sure VCR power is on.
• ON: Picture is displayed even if signal
• Make sure Remote is in VCR mode.
is very weak but quality may be
• Aim Remote Control directly at remote sensor on VCR.
poor.
(BO p. 7)
OFF: Screen turns solid blue when signal
• Avoid any object blocking signal path.
is weak or non-existent.
• Check Remote batteries. (BO p. 3)
• Selecting ON has no effect on connected
• Make sure VCR LOCK is set to off. (AO p. 10)
equipment with blue back feature.
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
3
Press ACTION to return to normal screen.
ACTION and PROG buttons do not • Check connections between VCR, external antenna,
respond... and TV.
• Press VCR button for VCR mode. (AO p. 2)
• Check Remote batteries. (BO p. 3)
VCR Lock Feature
Miscellaneous Correction
When set to ON, all operations except for timer
Programs cannot be viewed on TV... • Make sure TV power is on.
record and tape eject are prohibited. Useful for
• Make sure TV is set to output of VCR.
households with small children.
• Check connections between VCR, external antenna,
To turn on, hold down and TV.
REC on the VCR in Stop
• Set VCR/TV selector to "TV." (BO p. 5, AO p.10)
VCR LOCK ACT I VATED mode with no tape
• Make sure proper signal source is selected.
inserted for 7 sec.
• Insert the cassette with window side up; record tab
(Please ignore the NO Video cassette cannot be inserted...
CASSETTE warning.) facing you.
• Check if a tape is already in the unit.
To turn off, repeat above.
Video cassette cannot be removed... • Confirm Power Plug is fully inserted into an AC outlet.
VCR LOCK OFF Video cassette ejects when a • Make sure cassette record tab is intact. (BO p. 3)
recording is started or the power is
turned off for timer recording...
In Stop mode, the motor • To enable Quick play mechanism, the cylinder will rotate
• VCR Lock cancels in 24 hours if clock is set.
(CYLINDER) continues to rotate... for about 3 minutes. This reduces response time from
Stop to Play mode and from Play to Rewind Search
mode.
If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : consumerproducts@panasonic.com
REC
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 10 -
- 11 -
2003/01/08, 16:52
Reset Language, Channels, Clock, VCR's Output Channel
Press ACTION*
VCR CLOCK CHANNEL
REPEAT PLAY : OFF
REMOTE WARNING : ON
to display MENU.
AUTO SHUT- OFF : OFF
AUTO VCR/TV : ON
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH : 3
SELECT :
Video Cassette Recorder
EXIT : ACT I ON
Language Channels Clock Time Zone
Operating Instructions
Adjust
1) Press to select 1) Press to select 1) Press to select
language item. CHANNEL. CLOCK.
(Only when Auto Clock
(Advanced Operations)
is set.)
VCR CLOCK CHANNEL VCR CLOCK CHANNEL VCR CLOCK CHANNEL
REPEAT PLAY : OFF ANTENNA : CABLE AUTO CLOCK SET
REMOTE WARNING : ON AUTO SET MANUAL 1) Press to select
AUTO SHUT- OFF : OFF For Basic operations, see the separate
WEAK SIGNAL DISPLAY : OFF TIME ZONE ADJUST : 0
AUTO VCR/TV : ON CLOCK.
IDIOMA/LANGUE : ENGLISH "Basic Operations" instruction book.
VCR' S OUTPUT CH : 3
VCR CLOCK CHANNEL
SELECT : SET : SELECT : SELECT : AUTO CLOCK SET
EXIT : ACT I ON EXIT : ACT I ON EXIT : ACT I ON MANUAL
TIME ZONE ADJUST : 0
2) Press repeatedly. 2) Press to select 2) Press to select Model No.
"ANTENNA," then "MANUAL," and press
VCR CLOCK CHANNEL SELECT :
REPEAT PLAY : OFF press to set . (For Auto Clock Set,
EXIT : ACT I ON
REMOTE WARNING : ON
select "AUTO CLOCK
AUTO SHUT- OFF : OFF your antenna system
2) Press to select
AUTO VCR/TV : ON
IDIOMA/LANGUE : ENGLISH ("TV" or "CABLE.") SET.")
"TIME ZONE
VCR' S OUTPUT CH : 3
VCR CLOCK CHANNEL VCR CLOCK CHANNEL ADJUST"
SELECT : SET :
EXIT : ACT I ON ANTENNA : CABLE AUTO CLOCK SET
AUTO SET MANUAL
WEAK SIGNAL DISPLAY : OFF VCR CLOCK CHANNEL
For English TIME ZONE ADJUST : 0
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
VCR RELOJ CANAL
REPETICION :INACT SELECT : SET : SELECT : SET :
AVISO/CONT.REMOTO :ACT
EXIT : ACT I ON EXIT : ACT I ON
APAGADO AUTOMATICO :INACT
VCR/TV AUTO :ACT 3) Press to select SELECT : SET :
("TIME ZONE ADJUST" EXIT : ACT I ON
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA :3
"AUTO SET," then appears only when
and press to
ELEGIR : FIJAR : press . auto clock is set.)
SAL I R : ACT I ON subtract or add
• If you use Cable hour(s) as necessary.
For Spanish VCR CLOCK CHANNEL
Box, set it to the
6 /08 / 20 20 0 3 SUN SUN 2 2 : --PM
3) Press ACTION.
MAGNETO. HORL. CANAL PBS channel in your
REPRISE LECTURE : NON DST:ON
MESSAGE D' ERREUR : OUI time zone. • "TIME ZONE
SELECT HOUR
COUPURE AUTO : NON
MAGNETO. /TELE AUTO : OUI ADJUST" returns to
SELECT : SET :
LANGUAGE/IDIOMA : FRANÇAIS VCR CLOCK CHANNEL
EXIT : ACT I ON "0" if clock is set
CA SORTIE : 3
SEL. : REGLER: manually.
3) Press and
QUITTER : ACT I ON
to select and set
For French
CH AUTO SET PROCEEDING
the date, time, and
CANCEL : STOP DST (Daylight
3) Press ACTION to exit.
Saving Time).
• After Channel Auto
Set is finished, Auto 4) Press ACTION to
Clock Set will be start the Clock and
performed. exit this mode.
VCR's Output Channel
Add or Delete a Channel
1) Press to select
Table of Contents
"VCR'S OUTPUT CH."
To add channel:
VCR CLOCK CHANNEL Select channel with NUMBER keys and
REPEAT PLAY : OFF
REMOTE WARNING : ON Multi-Brand Control Feature ..................................... 2
press ADD/DLT.
AUTO SHUT- OFF : OFF
AUTO VCR/TV : ON
IDIOMA/LANGUE : ENGLISH
Advanced Connections (Cable/DSS) ....................... 3
VCR' S OUTPUT CH : 3
CHANNEL 08 ADDED
SELECT : SET : On-Screen Displays (OSD) ...................................... 4
EXIT : ACT I ON
2) Press . Warning and Instruction Displays ............................. 5
VCR CLOCK CHANNEL Tape Operation .................................................... 6, 7
IF YOU PRESS ACTION
To delete channel:
KEY, VCR ' S OUTPUT CH
Copying Your Tapes (Dubbing) ................................ 9
SWITCHES TO CH 4.
Select channel with CH / or NUMBER
Special VCR Features ............................................ 10
keys and press ADD/DLT.
Before Requesting Service .................................... 11
3) Press ACTION.
CHANNEL 08 DELE TED
Reset Language, Channels, Clock, VCR's Output Channel ...
VCR CLOCK CHANNEL
PLEASE TUNE YOUR TV TO
CH 4.
After 3 seconds
VCR CLOCK CHANNEL
REPEAT PLAY : OFF DST (Daylight Saving Time)
REMOTE WARNING : ON
AUTO SHUT- OFF : OFF
AUTO VCR/TV : ON
IDIOMA/LANGUE : ENGLISH VCR auto adjusts clock for DST.
VCR' S OUTPUT CH : 4
Spring (First Sunday in April)
SELECT : SET : DST:ON ➛ Sets clock ahead one hour.
EXIT : ACT I ON
Autumn (Last Sunday in October)
• To Make Corrections,
DST:ON ➛ Turns clock back one hour.
repeat steps 1) ~ 3). Please read these instructions carefully before attempting to connect,
• If your area does not observe Daylight
operate or adjust this product. Please save this manual.
Saving Time, select DST:OFF.
• Keep these time changes in mind when
programming VCR for timer recordings.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
- 12 -
PV-V4022-A
12
E S ®
As an NERGY TAR Partner,
Matsushita Electric Corporation of America
has determined that this product or product
E S
model meets the NERGY TAR ®
guidelines for energy efficiency.
LSQT0699A