Related Manuals for Panasonic WV-BS300
Summary of Contents for Panasonic WV-BS300
- Page 1 Combination Camera WV-BS300 Before attempting to connect or operate this product, please read these instructions completely...
- Page 2 If you lose the fuse cover the plug must not be used until a replacement cover is obtained. REFER SERVICING TO QUALIFIED SERVICE A replacement fuse cover can be purchased from your local Panasonic PERSONNEL. Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE...
-
Page 4: Table Of Contents
CONTENTS PREFACE ............INSTALLATION ..........17 FEATURES ............CONNECTIONS ..........19 PRECAUTIONS ..........SYSTEM CONNECTION ........20 MAJOR OPERATING CONTROLS AND PREVENTION OF BLOOMING THEIR FUNCTIONS ........... AND SMEAR ............21 SETUP PROCEDURE ........SPECIFICATIONS ..........22 Setup Menu ..........ACCESSORIES ........... -
Page 5: Preface
• Do not drop the metallic parts through slots. CCD and provides 570-line horizontal resolution This action could permanently damage this and 46 dB of S/N ratio. Also WV-BS300 feature unit. Do turn the power off immediately and advanced digital signal processing circuit which refer servicing to qualified service personnel. -
Page 6: Major Operating Controls And Their Functions
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS (1) Video Output Connector (5) Fall Prevention Wire (2) Power Cable (6) Decoration Cover (3) Camera Mounting Angle (7) Dome Cover (4) Pan/Tilt Starting Point - 3 -... -
Page 7: Setup Procedure
SETUP PROCEDURE Setup Menu This camera utilizes a user setup menu that is displayed on-screen. This setup menu contains various submenus with a Tree-Type structure as shown below. This menu is described in "Setup Menu Description" Setup on page 6. Menu Camera Light... - Page 8 Auto-Pan Special On/Off Menu AP Gain Pedestal Camera Reset • In Case of WV-RM70 Up Switch: Moves the cursor upwards. Down Switch: Moves cursor downwards. Right Switch: Moves the cursor to the right. The mode is also selected by this switch and adjustment of certain levels can be made by this Up Switch...
-
Page 9: Setup Menu Description
In this mode, even though the back light may vary, the object at the centre of the screen can still be clearly seen. <WV-BS300 Preset ON> Note: Refer to "Light Control Setting" on page 10 Night for detailed procedures. - Page 10 A conventional camera cannot cope with these level adjustment (LEVEL) while in the preset situations. "OFF" mode for both the "ALC" and "ELC" However, by using the WV-BS300 in the preset modes. "OFF" mode, it is possible to compensate for Note: difficult lighting conditions.
-
Page 11: Setting Procedures
(6) Synchronization (SYNC) Important Notice: The priority of sync mode is as follows: 1. Multiplexed Vertical Drive (VD2) (Highest) 2. Line-lock (LL) 3. Internal Sync (INT) (Lowest) Note: The automatic sync mode selection is made according to priority listed above. Refer to "Synchronization Setting"... -
Page 12: Camera Setting
SPACE POSI RET RESET • When the camera identification character needs editing, perform the WV-BS300..following steps by using the submenu of camera identification. • Move the cursor to "CAMERA ID" and press the CAM (SET) button to display the character editing menu. - Page 13 SPACE POSI RET RESET more than 0.5 seconds. WV-BS300..• After completing the positioning of the camera ID, press the CAM (SET) button to return to the character editing menu. • To return to the normal camera picture mode, move the character cursor to "END"...
- Page 14 (1)-1 ALC Mode with Preset Mode (PRESET ON) • Move the cursor to "PRESET" and select "ON" by using the joystick. The preset mode menu is displayed on the monitor screen as shown. • Move the cursor to "RET" by using the joystick and press the CAM (SET) button to return to the setup menu. Blinking Blinking Turns to white...
- Page 15 (2) MANUAL Mode Manual setting menu Move the cursor to "ALC/MANUAL" by using the joystick and select * MANUAL CONT * "MANUAL" by using the joystick. IRIS ..I..CLOSE OPEN The "MANUAL" menu is displayed. Control the level by using the joystick. 4.
- Page 16 Line-lock Sync Mode (LL) Camera setting menu • Display the setup menu. • If necessary, refer to "Setup Menu Display" on page 8 for details on ** SET UP ** displaying the setup menu on the monitor screen. CAMERA ID OFF * ALC/MANUAL ALC *...
- Page 17 Notes: 1. When the cursor "I" reaches to the end of the "+" position, the cursor "I" jumps to the " " position. At the same time, the step number of the "COARSE" mode increases one step to enable a continuous adjustment. The reverse operation takes place when the cursor "I"...
- Page 18 4. To set a speed Move the cursor to "SPEED", and move the joystick to the left or right ** AUTO PAN ** to set a panning speed as desired. POSITION START Panning speed increases when the joystick is moved leftward, or SPEED ...I..
- Page 19 (3) Camera Resetting Move the cursor to "CAMERA RESET" by using the joystick, and * SPECIAL * press the F3 button. AP GAIN ..I..This camera is reset to the factory preset condition. PEDESTAL .I..(In case of WV-RM70, keep pressing the Right, Left and Set switches CAMERA RESET PUSH SW simultaneouly more than 2 seconds.)
-
Page 20: Installation
INSTALLATION 1. Remove the mounting screw (M3) from the camera mounting angle (provided). 2. Mark the mounting holes into the ceiling by Precautions : using the removed camera mounting angle as 1. The following all installations should be made a template. by qualified service personnel or system installers and should confirm to all local codes. - Page 21 4. Hang the fall prevention wire to the camera 6. Tighten the mounting screw (provided). mounting angle. Notes : 1. Tighten the camera fixing screw with the screwdriver. 2. Do mount the camera and camera mounting angle completely as shown in the following.
-
Page 22: Connections
CONNECTIONS Precaution: The following connections should be made by qualified service personnel or system installers. 220 - 240V AC Video Output Cable Coaxial Cable BNC Plug (5C - 2V) BNC Plug To Video IN (CAMERA IN) Coaxial cable length should be less than 1200m (with 5C - 2V) Notes: •... -
Page 23: System Connection
SYSTEM CONNECTION Combination Camera Max. 64 Camera Receiver Matrix Switcher VTR (up to 16) Personal Computer RS-232C Port CONTROL ALARM INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1... -
Page 24: Prevention Of Blooming And Smear
PREVENTION OF BLOOMING AND SMEAR When the camera is aimed at a bright light, such as a spot light, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. -
Page 25: Specifications
SPECIFICATIONS Combination Camera Power Source : 220 - 240V AC, 50Hz 11W Ambient Operating Temperature : 10°C - +50°C (14°F - 122°F) Dimensions : 130 (D) x 195 (H) mm Weight : Camera Pick-up Device : 1/3” CCD with 753 (H) x 582 (V) pixels Synchronization Internal/Line-lock/VD2 Horizontal Scanning Frequency :...