Before Operating This Unit - Onkyo TX-SV353 Instruction Manual

Before operating this unit

ANTENNA
REAR SPEAKERS CENTER
R L SPEAKER
AM
WARNING AVIS
MANUFACTURED UNDER LICENSE FROM DOLBY
RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN NE PAS OUVRIR LABORATORIES LICENSING CORPORATION.
"DOLBY", THE COUBLE-D SYMBOL AND "PRO LOGIC"
VIDEO-1 VIDEO-2 MONITOR
FM ARE TRADEMARKS OF DOLBY LABORATORIES
75 OUTPUT
INPUT OUTPUT INPUT LICENSING CORPORATION.
GND
V V FRONT SPEAKERS
R L
OUTPUT INPUT
(REC) (PLAY) INPUT OUTPUT INPUT SUB-
A A
WOOFER
L L PRE OUT
B B
R R
R L
PHONO CD TV/AUX TAPE VIDEO-1 VIDEO-2
CAUTION: SPEAKER IMPEDANCE
FRONT A OR B: 6 OHMS MIN. / SPEAKER
FRONT A+B: 12 OHMS MIN. / SPEAKER
CENTER / REAR: 6 OHMS MIN. / SPEAKER
ANTENNA
REAR SPEAKERS CENTER
R L SPEAKER
AM
WARNING AVIS
MANUFACTURED UNDER LICENSE FROM DOLBY
RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN NE PAS OUVRIR LABORATORIES LICENSING CORPORATION.
"DOLBY", THE COUBLE-D SYMBOL AND "PRO LOGIC"
MONITOR
FM VIDEO-1 VIDEO-2 ARE TRADEMARKS OF DOLBY LABORATORIES
OUTPUT
75 INPUT OUTPUT INPUT LICENSING CORPORATION.
GND
V V FRONT SPEAKERS
R L
OUTPUT INPUT
(REC) (PLAY) INPUT OUTPUT INPUT SUB-
WOOFER A A
L L PRE OUT
B B
R R
R L
PHONO CD TV/AUX TAPE VIDEO-1 VIDEO-2
CAUTION: SPEAKER IMPEDANCE
FRONT A OR B: 6 OHMS MIN. / SPEAKER
FRONT A+B: 12 OHMS MIN. / SPEAKER
CENTER / REAR: 6 OHMS MIN. / SPEAKER
Insert the batteries into the remote controller according to the illustration.
1
Remote controller sensor
STAND-BY indicator
VOLTAGE SELECTOR
AM FREQ. STEP
9kHz 10kHz
REMOTE AC OUTLETS
CONTROL SWITCHED
TOTAL 100W MAX.
AUDIO VIDEO CONTROL
RECEIVER
MODEL NO. TX-SV353
RATING:
VOLTAGE SELECTOR
220-230V 120V
220-230V
AM FREQ. STEP
AM FREQ. STEP
9kHz 10kHz
REMOTE AC OUTLETS
CONTROL SWITCHED
TOTAL 100W MAX.
AUDIO VIDEO CONTROL
RECEIVER
MODEL NO. TX-SV353
RATING:
VOLTAGE SELECTOR
220-230V 120V
2
TX-SV353
30˚
30˚
approx. 5 m
(16 feet)
120V
9kHz 10kHz
3
Setting the voltage selector
(worldwide model only)
1. Determine the proper voltage for your
area: 220-230 V or 120 V.
2. If the setting on the voltage selector is
not correct, insert a screwdriver into the
groove in the switch and slide the
switch completely to the right (120 V)
or the left (220-230 V), whichever is
appropriate.
Setting the AM tuning step
frequency
(worldwide model only)
The worldwide model is equipped with a
switch that controls the AM (9 kHz/
10 kHz) band tuning steps.
Please set this switch to match the tuning
step frequency in your area.
U.S. & Canada: 10 kHz
Other areas: 9 kHz
Using the remote controller
The following information will help you
get optimal use from the remote controller.
Place this unit away from direct bright
light which can prevent proper opera-
tion of the remote controller.
Make sure audio rack doors do not have
tinted glass. Placing this unit behind
such a door may prevent proper remote
controller operation.
Loading the batteries
Remove the battery compartment cover by
opening it as shown in the illustration.
Load two AA (R6 or UM-3)-size batteries
into the remote controller with the plus (+)
and minus (–) terminals positioned as indi-
cated by the diagram inside the battery
compartment, then close the cover.
Remove empty batteries immediately to
avoid corrosion damage.
To avoid potential corrosion damage,
never mix old batteries with new ones.
The manganese batteries supplied with
this unit have a service life of approxi-
mately six months, depending on the
frequency of use.
The TX-SV353 comes equipped with
two AA (R6 or UM-3) manganese bat-
teries, but we recommend that long-life
AA (LR6 or AM-3) size alkaline batter-
ies be used when replacing the batteries.
5