Payne PA1P048 Installation & Start-Up Instructions page 4

r 2 ] RI WIN
1!6_00_
COMPREGSORIBLOWER,ELECTRIC IiEAT x
& ELECTRIC ACCESS \
_0006
[42 94]
?
i
J
I
J
TOP VIEW
I}93 9
[47003
_2263
• 4 \\ [48 28]
[44 22} \\
\ DIIAII_ OUIL[I
190 [0¸?5) N PT
LEFT SIDE VIEW _2_0_08._ FRONT VIEW
DIMENSONS R
{] ARE N NCHES
C01L
4000
880
[3 481
REAR VIEW
POWR ENTRY
202 [088] OIA HOLE
CON [ROL ENIR¥
I [ 21J
326 I _ ........ "%
[12 84]
[3 43]
[481 [0 20
RIGHT SIDE VIEW
REQUIRED CLEARANCE TO COMBUSTIBLE MATL
INCHES [mm]
TOP OF UNIT ................................................................................... 1400 [355 6]
DUCT SIDE OF UNIT ......................................................................... 200 [50.8]
SIDE OPPOSITE DUCTS ................................................................ 1400 [355 6]
BOTTOM OF UNIT ............................................................................. 050 [12.7]
ELECTRIC HEAT PANEL ................................................................. 3600 [914 4]
NEC: REQUIRED CLEARANCES,
INCHES [mini
BETWEEN UNITS, POWER ENTRY SIDE .................................... 42.00 [1066 8]
UNIT AND UNGROUNDED SURFACES, POWER ENTRY SIDE .36.00 [914.0]
UNIT AND BLOCK OR CONCRETE WALLS AND OTHER
GROUNDED SURFACES, POWER ENTRY SIDE ......................... 42.00 [1066 8]
UNIT
PAIP048
PA1P060
PA2P042
PA2P048
PA2P060
REQUIRED CLEARANCE FOR OPERATION AND SERVICING
INCHES [ram]
EVAR COIL ACCESS SIDE ............................................................ 36.00 [914.0]
POWER ENTRY SIDE .................................................................... 36.00 [914.0]
(EXCEPT FOR NEC REQUIREMENTS)
UNIT TOP ....................................................................................... 48.00 [1219 2]
SIDE OPPOSITE DUCTS .............................................................. 36.00 [914.0]
DUCT PANEL ................................................................................. 12.00 [304.8] *
*MINIMUM DISTANCES: IF UNIT IS PLACED LESS THAN 3048 [12 00] FROM
WALL SYSTEM, THEN SYSTEM PERFORMANCE MAYBE COMPROMISE
Note: Wire Grilles are a field installed option.
C99006
ELECTRICAL CHARACTERISTICS
208/230-io60, 208/230o3o60, 460-3°60
208/230olo60, 208/230o3o60, 460°3°60
208/230-1o60, 208/230o3o60, 460-3°60
208/230olo60, 208/230o3o60, 460°3-60
208/230-1o60, 208/230o3o60, 460-3-60
UNIT WEIGHT
lb, k8
324 145
389 176
321 i46
326 148
399 i81
UNIT HEIGHT
IN. (MM)
_A _
38.98 (9902)
38.98 (990.2)
38.98 (990.2)
38.98 (990.2)
42.98 (!091.i)
CENTER OF GRAVITY
IN. (MM)
X Y
20.0 (508.0) 17.0 (432.0)
19.0 (482.6) 16.0 (406.0)
20.5 (520.7) 16.75 (425.5)
19.5 (495.3) 17.6 (447.6)
20.5 (520.7) i6.2 (412.8)
Z
17.0 (432.0)
17.0 (432.0)
16.6 (421.6)
18.0 (457.2)
17.6 (447.0)
Fig. 3-- PAl P048=060 and PA2P042-060 Unit Dimensions
CuIb should be level to within 1/4 in (See Fig. 5A) ]"his is necessary for unit drain to fhnction properly Refer to accessory roof curb installation
instructions f_}r additional infbm_ation as required
g. SLAB MOUNT
Place d_e unit on a solid, level concrete pad that is a minimum of 4 in d_ick with 2 in above grade (See Fig. 5B) The slab should extend
approximately 2 in beyond the casing on all 4 sides of the unit Do not secure the unit to the slab except when required by local codes.
4