Advertisement
Reinstall
the storage
drawer,
CompJete
installation
steps
9 through
24,
Checking
for proper
cooktop
burner
and
oven
flame
is very
important,
You must
adjust
"LOW"
setting
for each
cooktop
burnec
See Step
l&
The small
inner
cone
shouJd
have
a very
distinct
Mue
flame
1/4" (6 ram) to 1/2"
(13 ram}
bng,The
outer
cone
is not as
distinct
as the
inner
cone.
LR gas flames
may
have a sJightJy
yellow
tip,
if the
flame
is noisy
or bbwing,
it is getting
too
much
air. If the flame
is soft and Hazy,
it is not getting
enough
air,
NaturaU
gas conversion
[] Complete
installation
steps
1
through
8 before
converting
cooktop
to
natural
gas. Check that
main
gas supply
line
has been
shut
off and the power
supply
cord
is disconnected,
[] Pressure
regulator:
Remove
storage
drawer
and locate
pressure
regulator
at back of range.
Do not remove
the pressure
regulator
Remove
plastic
cover,
Turn
cap marked
"LR"
on front
of pressure
regulator
counterclockwise
with
a wrench
to
remove,
Do not disturb
or remove
the
spring
beneath
the cap.Turn
the cap over
and reinstall
cap on regulator
so that the
letter
"N"
is visible,
Replace
plastic
cover
over
cap,
j
pressure regulator
plastic
cover
Natural
L.R
--cap
--
washer
Natural
gas
LR gas
[] Surface
burners:
Remove
burner
caps.
Use a Phillips
or Quadrex
screwdriver
to remove
the two
screws
holding
the burner
head
down,
Lift the
burner
head
off the cooktop
to uncover
the orifice
spud
holder,
The orifice
spud
is recessed
in the holder,
NOTE:
Reinstall
one of the screws
through
the range
cooktop
to hold
orifice
spud
holder
in place
while
removing
and
replacing
orifice
spuds,
orifice spud
reinstall one
,_\
of the screws
",..
_
spark electrode
\
orifice spud
honer
_
range cooktop
Locate
the Natural
gas
orifice
spuds
on the spud
card
on the back of the
range,
Orifice
spuds
are
stamped
with
a number
and marked
with
two
color
dots,
Natural gas
orifice spud
Natural
Gas
Surface
Propane rate
Orifice
Color
burner
(BTU/hr)
Number
Marking
Left
9,500
N151
Blue/
rear
Brass
Left
13,500
N186
Blue/
front
Orange
Right
9,500
N151
Blue/
front
Brass
Right
5,000
Nl12
Blue/
rear
White
Locate
the brass
orifice
spuds
in the
center
of each burner
throat
about
2"
(5 cm) below
the cooktop,
Apply
masking
tape
to the end of a 5/16"
nut
driver
to fit snugly
over
the orifice
spud,
Press
driver
down
onto
the spud
of the
left front
burner
and remove
by turning
spud
counter-clockwise
and lifting
it out,
Replace
the LR gas spud
with
the
appropriate
Natural
gas spud
shown
in
the table,
Continue
to replace
the remaining
orifice
spuds,
one at a time,
Place the LR gas
spuds
on the spud
card
on the
back of
the
range
for future
use. Replace
burner
caps using
both
screws
and burner
grates,
Oven
burner:
Use
1/2" combination
wrench
to loosen
the orifice
hood
away
from
pin
(approximately
2 to 2-1/2 turns),
The burner
flame
cannot
be properly
adjusted
if this conversion
is not made,
_-
orifice hood
hood-_,
jl/atural
gas:
•
_;_'!_'_
d/
increase gas,
pln_
_j._
I_jt
_
increase flame size
_//_.
(pre-set at factory')
L,R gas:
___:::7::_/;j
decrease gas,
decrease flame size
[] Broil
burner:
Use
1/2" combination
wrench
to loosen
orifice
hood
away
from
pin (approximately
2 to 2-1/2 turns},The
burner
flame
cannot
be properly
adjusted
if this conversion
is not made,
orifice hood
Reinstall
the storage
drawer,
Complete
installation
steps
9 through
24,
Checking
for proper
cooktop
burner
and
oven
flame
is very
important,
You must
adjust
"LOW"
setting
for each
cooktop
burner,
See installation
step
l&
NOTE:
Natural
gas flames
do not have
yellow
tips,
11
Advertisement
