Advertisement
c)
Warning
-
Remove
transport
tape
from
the
lights
and
the
filters
before
use.
d)Sufficient
air
is needed
to provide
proper
combustion
and exhausting
of gases
through
the
flue
(chimney)
of fuel
burning
equipment
to prevent
back
draughting.
Follow
the heating
equipment
manufacturer's
guideline
and
safety
standards
such
as those
published
by the
National
Fire
Protection
Association
(NFPA),
and
the
American
Society
for
Heating,
Refrigeration
and
Air
Conditioning
Engineers
(ASHRAE),
and the local
code authorities.
e)When
cutting
or drilling
into
wall
or ceiling,
do not
damage
electrical
wiring
and
other
hidden
utilities.
f) This appliance
must always be vented to the outdoors.
g)The
canopy is heavy: overall weight 65 Ibs (29kg).
Please ensure adequate care when installing the
canopy to prevent personal injury,
The canopy must be installed onto a solid wall or solid studs,
h)Before
servicing
or cleaning
uniL switch
power off at the service
panel and lock the service
disconnection
means to prevent
power from being switched
on accidentally.
When the service
disconnection
means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
i) WARNING
- TO
REDUCE
THE
RISK
OF
FIRE,
USE
ONLY
METAL
DUCTWORK.
WARNING - GROUNDING
INSTRUCTIONS
a)This
appliance
must
be grounded.
In the
event
of an electrical
short
circuit,
grounding
reduces
the
risk of electrical
shock
by providing
an escape
wire
for the electric
current.
This
appliance
is equipped
with
a cord
having
a grounding
wire
with
a grounding
plug.
To provide
protection
against
electric
shock
the
plug
must
only
be plugged
into
an outlet
that
is properly
installed
and
grounded.
b)WARNtNG
- Improper
grounding
can result
in a risk of electric
shock.
c)Appliance
to be connected
to a 15/20A
circuit
breaker.
d)Consult
a qualified
electrician
if the
grounding
instructions
are
not completely
understood,
or if
doubt
exists
as to whether
the appliance
is properly
grounded.
e)Do
not
use an extension
cord.
If the power
supply
cord
is too
short,
have
a qualified
electrician
install
an outlet
near the appliance.
t
Ceiling hei ht
installationheight
T6" to 8'1"_"
24" to 30"
(2290 to 2690)
(610 to 760)
NOTE:
Stainless
steel
and
iridium
is very
easily
damaged
during
installation
if abraided
or knocked
by tools.
Read
the instructions
before
starting
the assembly.
Remove
the filters
to
allow
access
to wall
mounting
holes.
The unit
is designed
for ceilings
7' 6" to 8' 10" (2290
to 2690mm)
high.
The chimney
is telescopic
and is designed
to adjust
between
25~1/2"
and
35-1/2"
(650 to 900mm).
Ascertain
the desired
installation
height
of the canopy.
NOTE:
Installation
height
ranges
from 24" to 30" (610 to 760mm).
DUCTING:
Ducting
accessories
are not supplied.
The
air outlet
from
the adaptor
(attached
to the motor)
is 7"(178mm).
7"(178mm)
ducting
will
require
a clearance
hole
of 7~5/16"
(186mm)
in
the
ceiling.
INSTALLING
MOUNTING
BRACKET
(See
diag.
1 on following
page)
Align
the
center
of the installation
bracket
with
the center
of the cooking
surface
(use
of plumb
bob
recommend).
Place
theflat/horizontal
surface
of the
mounting
bracket
8-1/2"(216mm)
abovethe
installation
height
(diag.1).
Ensuring
the
mounting
bracket
is level,
mark
and
drill
the
holes
in
the wall.
Use the
screws
and plugs
provided
to attach
bracket.
INSTALLING
CHIMNEY
BRACKET
Cut
cornice
to
suit
the
chimney
cover.
Align
the
center
of
the
chimney
bracket
with
the
center
of
the
cooking
surface.
Mark
and
drill
the
holes
in
the
wall
and
ceiling.
Use
the
mounting
screws
and
anchors
provided.
Advertisement
