Related Manuals for D-Link DI-2000 Series
Summary of Contents for D-Link DI-2000 Series
-
Page 1: User Manual
D-Link DI-2000 Series Routers User Manual First Edition (December 2004) Building Networks for People... -
Page 2: Table Of Contents
content Table of Content Chapter 1 Introduction of Function ............................1 1.1 Support a variety of protocols..........................1 1.1.1 Suitable for a variety of network environments ..................1 1.1.2 Support the Ehernet Protocol and ARP protocol ..................1 1.1.3 Variety of WAN protocols .......................... 1 1.1.4 TCP/IP protocols on the network layer...................... - Page 3 content 4.1 Installation Specification............................23 4.2 Mount the Routers in a Standard Rack ....................... 23 - II -...
-
Page 4: Chapter 1 Introduction Of Function
1.1.1 Suitable for a variety of network environments The DI-2000 series of routers is suitable for a variety of network environments. The DI-2000 series complies with the requirement about routers in IETF RFC1812 and supports most network protocols: X.25, FR, synchronous/asynchronous PPP, SLIP, HDLC, Ethernet, IP, ICMP, TCP, UDP, OSPF, RIP(version 1&2) ,SNMP(version 1&2),... - Page 5 Supports the encapsulation of the upper protocols on X.25, such as IP. Supports switching between SVCs or PVCs of each synchronous port. The DI-2000 series can be as X.25 small packet switches, also can connect multiple X.25 devices through a special line connected with the public packet switching network.
-
Page 6: Tcp/Ip Protocols On The Network Layer
DI-2000 Series Routers hardware installation manual Complies with RFC1662 , supports the encapsulation of IP and other upper protocols above PPP and realizes IPCP in network control protocols(NCPs). Complies with RFC1334, and supports two general authentication protocols, including PAP and CHAP. -
Page 7: Multiple Dynamic Routing Protocols On Ip
DI-2000 Series Routers hardware installation manual 1.1.5 multiple dynamic routing protocols on IP Supports multiple dynamic routing protocols on IP. The series supports the Open Shortest Path First (OSPF) protocol and dynamic routing protocol (version 1 & 2). The series achieves own BIGP protocol in order to connect with EICRP of Cisco. -
Page 8: Friendly User Interface
When the master line disconnects, the routers switches to backup lines automatically because of receiving nothing of routing information. The above solution adds system load, so the DI-2000 series also supports dynamic transmission according to demand, which doesn’t run the dynamic routing protocol with the master routing effective until the routers switch to backup lines. -
Page 9: Supports Saving Current Deployment
DI-2000 Series Routers hardware installation manual Logins and deploys through TELNET Logins and deploys through PAD(X.29) Logins and deploys through remote dialing 1.4.2 Supports saving current deployment It can be used in similar deployment to network deployment, and save malfunction spots to help support the engineer to discover and solve malfunctions. -
Page 10: Chapter 2 Introduction Of The Di-2004 Router
DI-2000 Series Routers hardware installation manual Chapter 2 Introduction of the DI-2004 router 2.1 Exterior Specification of the DI-2004 Router 2.1.1 Appearance of the router 1. The indicator distribution and specification of the front panel Figuer 2-1 Front Panel of the DI-2004 2. -
Page 11: Hardware Technical Specifications
DI-2000 Series Routers hardware installation manual Serial 0 Serial port 0 Connect to synchronous or asynchronous Modem. The used line is the special monitoring cable, and you can see connection specification in Charter 2.3 “Ports Connection Specification”. Serial 1 Serial port 1 Connect to synchronous or asynchronous Modem. -
Page 12: Port Connection Specification
DI-2000 Series Routers hardware installation manual 0¡ æ to 40¡ æ Operating temperature -20¡ æ to 65¡ æ Nonoperating temperature 10% to 85% noncondensing Operating relative humidity Nonoperating relative humidity 5% to 95% noncondensing Input voltage£ º 170 to 264 V£ » input frenquency :47 Power to 63Hz£... -
Page 13: The Console Port
DI-2000 Series Routers hardware installation manual External Receive Data RXDB Used for selecting V.35 ECLKA- Express Clock Output within A group DTE→DCE; used for V.35 (negative) Express Clock Output within B group ECLKB+ DTE→DCE; used for V.35 (positive) External Receive Clock RXCA Used for selecting V.28... - Page 14 DI-2000 Series Routers hardware installation manual Figuer 2-3 Pin distribution of RJ45 RJ45 plug and RJ45 jack is corresponding according to the ordinal number of 1 to 8 from the left to the right. PIN description is shown in the following table.
-
Page 15: External Connection Specification Of Ports
DI-2000 Series Routers hardware installation manual Table 2-6 Pin Description of AUI Interface Name Symbol Comment Collision Detect (positive) ACX+ Input Send Data(positive) ATXD+ Output Receive Data(positive) ARXD+ Input Collision Detect(negative) ACX- Input Transmit Data(negative) ATXD- Output Receive Data(negative) ARXD-... - Page 16 DI-2000 Series Routers hardware installation manual Figuer 2-5 V.35 MODEM cable 2. Extenal connection Specification of Console port The cable connects the Console port of DI-2004 and external terminal Console devices. One end is a 8 pin jack, and the other is a 25 aperture connector(DB25) and a 9 aperture connector(DB9).
- Page 17 DI-2000 Series Routers hardware installation manual Figuer 2-7 Ethernet TP Straight Cable Connection - 14 -...
-
Page 18: Chapter 3 Introduction Of The Di-2006 Router
DI-2000 Series Routers hardware installation manual Chapter 3 Introduction of the DI-2006 Router 3.1 Overview The DI-2006 has a multi-protocol synchronous, asynchronous serial port and a ISDN BRI port. Besides that, the router has a 10M Ethernet port(thick cable or thin cable interface), with which business LANs can connect to Internet or DDN through ISDN, PSTN, DDN, Frame Relay and X.25. -
Page 19: Processor
DI-2000 Series Routers hardware installation manual 3.1.5 Processor Motorola 68EN360@33Mhz 3.1.6 Memory EPROM: 256KByte FLASH RAM: 2Mbyte. It can be enlarged to Mbyte. DRAM: 8MByte 3.1.7 Features The router supports multiple network protocols with strong function. The application layer: TELNET, X.29 and TFTP... -
Page 20: Exterior Specification Of The Di-2006
DI-2000 Series Routers hardware installation manual 3.2 Exterior Specification of the DI-2006 3.2.1 Exterior Specification 1. The Front Panel of the DI-2006 Figuer 3-1 The Front Panel of the DI-2006 2. The Rear Panel of the DI-2006 Figuer 3-2 Rear Panel Interface Distribution of the DI-2006 Switches and interfaces on the rear panel of the DI-2006 are shown as Figuer 3-2 meanings of which are shown as Table 3-1. -
Page 21: Port Connection Specification
DI-2000 Series Routers hardware installation manual BRI S/T ISDN Connect to S/T interface( RJ45) of ISDN network interface terminal(NT1) through the port ISDN When the line is enabled and D channel is active, the ACTIVE interface is active indicator will glint. -
Page 22: External Connection Specification Of Serial Ports On The Di-2006
DI-2000 Series Routers hardware installation manual Pin description of AUI(Attachment Unit Interface) is shown as Table 2-6. 4. ISDN S/T Interface of the DI-2006 router Table 3-2 PIN description of ISDN S/T Interface(RJ45 interface) is as shown below: Name Symbol... - Page 23 5. Cross Cable Connection Specification for Debugging cross cable on the Serial port Under certain conditions, two serial ports of a DI-2000 series of router needs to be crossed, or two DI-2000 series of routers connect back on the back according to the following connection methods.
- Page 24 Figuer 3-7 V.35 Cross Cable Connection Cross Cable on the Ethernet Port Two DI-2000 series of routers can be across interconnected with TP cross cable or AUI cross cable. TP cross cable can be used on straight connection of a router and the TP interface of a single host LAN card.
- Page 25 DI-2000 Series Routers hardware installation manual TP cross cable connection is shown as Figure 1-3-8. Figuer 3-8 Ethernet TP Cross Cable Connection Connect two Ethernet Ports (thicknet ports) with AUI cross cable AUI cross cable connection is shown as Figuer 3-9.
-
Page 26: Chapter 4 Installation Of The Routers
4.2 Mount the Routers in a Standard Rack There are two methods to attach brackets to the DI-2000 Series of routers as shown in Figuer 4-2 and Figuer 4-3 For the first method, first use screws to fix brackets on the two sides of the DI-2000 Series with the front panel forward (Figuer 4-2 only shows the right attachment, the same to the left). - Page 27 3 to 5 seconds from turning off the power. Please try to use the “reboot” command to restart the routers. Please don’t bump the routers or make the DI-2000 series fall from high. Such operations may harm the internal hardware of the routers.
-
Page 28: Warranty And Registration Information
Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service. - Page 29 D-Link's applicable product documentation as being compatible. D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide compatibility when there is fault in the third-party hardware or software. D-Link makes no warranty that operation of its software products will be uninterrupted or absolutely error-free, and no warranty that all defects in the software product, within or without the scope of D-Link's applicable product documentation, will be corrected.
- Page 30 Hardware. Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware.
- Page 31 IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT.
- Page 32 DI-2000 Series Routers hardware installation manual Register online your D-Link product at http://support.dlink.com/register/ - 29 -...
- Page 33 Limited Product Warranty Period The Limited Product Warranty Period starts on the date of purchase from D-LINK. Your dated sales or delivery receipt, showing the date of purchase of the product, is your proof of the purchase date. You may be required to provide proof of purchase as a condition of receiving warranty service. You are entitled to warranty service according to the terms and conditions of this document if a repair to your D-LINK branded hardware is required within the Limited Product Warranty Period.
- Page 34 Performance of the Limited Product Warranty If a product defect occurs, D-LINK’s sole obligation shall be to repair or replace any defective product free of charge to the original purchaser provided it is returned to an Authorized D-LINK Service Center during the warranty period. Such repair or replacement will be rendered by D-LINK at an Authorized D-LINK Service Center. All component parts or hardware products removed under this limited warranty become the property of D-LINK.
- Page 35 Laufzeit der eingeschränkten Garantie Die Laufzeit der eingeschränkten Garantie beginnt mit dem Zeitpunkt, zu dem das Produkt von D-LINK gekauft wurde. Als Nachweis für den Zeitpunkt des Kaufs gilt der datierte Kauf- oder Lieferbeleg. Es kann von Ihnen verlangt werden, dass Sie zur Inanspruchnahme von Garantiediensten den Kauf des Produkts nachweisen. Wenn Ihre Hardware-Produkte der Marke D-LINK innerhalb der Laufzeit der eingeschränkten Garantie eine Reparatur benötigen, so sind Sie berechtigt, gemäß...
- Page 36 DI-2000 Series Routers hardware installation manual Bei Auftreten eines Produktfehlers besteht die einzige Verpflichtung von D-LINK darin, dem ursprünglichen Käufer das defekte Produkt kostenlos zu reparieren oder es auszutauschen. Voraussetzung hierfür ist, dass das Produkt während der Garantielaufzeit einem autorisierten D-LINK-Servicecenter übergeben wird. Reparatur oder Austausch werden von D-LINK durch ein autorisiertes D-LINK-Servicecenter durchgeführt.
- Page 37 Période de Garantie Produit Limitée La Période de Garantie Produit Limitée court à compter de la date d’achat auprès de D-LINK. La date de votre reçu ou bon de livraison correspond à la date d’achat du produit et constitue la date de votre preuve d’achat. Il est possible que le service de garantie ne vous soit accordé que sur production de votre preuve d’achat. Vous avez droit à un service de garantie conforme aux modalités énoncées dans les présentes dès lorsque que votre matériel de marque D-LINK nécessite une réparation pendant la Période de Garantie Produit...
- Page 38 DI-2000 Series Routers hardware installation manual Service Agréé D-LINK. Les composants, pièces ou produits retirés dans le cadre de cette garantie limitée deviennent propriété de D-LINK. La pièce ou le produit de remplacement est couvert par la garantie limitée de la pièce ou du produit d’origine pendant la période restante. Le produit de remplacement n’est pas nécessairement neuf, ni d’une marque ou d’un modèle identique ;...
- Page 39 Período de la garantía limitada del producto El período de la garantía limitada del producto se inicia en la fecha en que se realizó la compra a D-LINK. Para el comprador, el comprobante de la fecha de la compra es el recibo de la venta o de la entrega, en el que figura la fecha de la compra del producto.
- Page 40 D-LINK. Todos los productos de hardware o componentes que se eliminen bajo esta garantía limitada serán propiedad de D-LINK. La parte o el producto de repuesto adquiere, para el resto de la garantía limitada, el estatus de parte o producto eliminado. El producto de repuesto no ha de ser nuevo o de la misma marca, modelo o parte; D-LINK puede sustituir a discreción el producto defectuoso (o cualquier parte) con un producto equivalente reacondicionado (o superior) en cualquier material respecto al producto...
- Page 41 Il periodo di garanzia sopra specificato relativamente a tutti i prodotti D-LINK venduti nei Paesi europei da D-LINK o da qualsiasi suo rivenditore o distributore autorizzato decorre dal 1° gennaio 2004. Tutti i prodotti venduti nei Paesi europei da D-LINK o da uno qualsiasi dei suoi rivenditori o distributori autorizzati prima del 1° gennaio 2004 sono coperti da una garanzia di 5 anni fatto salvo per alimentatori, ventole e accessori che hanno 2 anni di garanzia.
- Page 42 Qualora comparisse un difetto o una non conformità, D-LINK avrà l’unico obbligo di riparare o sostituire il prodotto non conforme senza alcun costo per l’acquirente a condizione che il prodotto venga restituito a un Centro di Assistenza autorizzato D-LINK entro il periodo di garanzia. La riparazione o la sostituzione verranno eseguite da D-LINK presso un Centro di Assistenza autorizzato D-LINK.