Download Print this page

Electrolux EW3LDF65GSN Installation Instructions Manual

Freestanding dual fuel
Hide thumbs Also See for EW3LDF65GSN:

Advertisement

iNSTALLATiON
AND SERVICE
MUST
BE
PERFORMED
BY A QUALIFIED
iNSTALLER.
iMPORTANT:
SAVE
FOR LOCAL
ELECTRICAL
iNSPECTOR'S
USE.
READ
AND SAVE THESE
iNSTRUCTiONS
FOR
FUTURE
REFERENCE.
• ALL RANGES
CAN TiP
• INJURYTO
PERSONS
COULD
RESULT
• iNSTALL
ANTi=TIP
DEVICE
PACKED
WiTH
RANGE
• SEE iNSTALLATiON
iNSTRUCTiONS
I_
if the
information
in this j
manual
is not followed
exactly, a fire or I
explosion
may result causing
property I
damage,
personal
injury or death,
j
FOR YOUR SAFETY:
m
Do not store or use gasoline
or other
flammable
vapors and liquids in the
vicinity of this or any other appliance.
=
WHAT TO DO iF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch
any electrical
switch;
do
not
use
any
phone
in your
building.
• Immediately
call your gas supplier
from
a neighbor's
phone.
Follow
the gas supplier's
instructions.
• if you
cannot
reach
your
gas
supplier, call the fire department.
=
Installation
and
service
must
be
performed
by a qualified
installer,
service agency
or the gas supplier.
Clearances
and Dimensions
Location: Check location where the range will be
installed. Check for proper electrical and gas supply,
and the stability of the floor.
Dimensions that are shown must be used. Given
dimensions
provide minimum
clearance.
Contact
surface must be solid and level.
Refer to your serial plate for applicable
agency certifications
Provide Proper Fuel Type
Before Proceeding: You r range is preset to operate on h P.
(Liquified Petroleum) Gas only.
important
Note to the Consumer
= Keep these instructions with your Use & Care Guide for
future reference.
= As when using any appliance generating heat, there are
certain safety precautions you should follow. These are
listed in the Use & Care Guide, read it carefully.
• Be sure your range is installed and grounded properly
by a qualified installer or service technician.
Make sure the wall coverings around the range can
withstand the heat generated by the range.
To eliminate the need to reach over the surface
elements or burners, cabinet storage space directly
above the range should be avoided.
important
Notes
to the
installer
= Read all instructions contained in these installation
instructions before installing range.
Remove all packing material from the oven
compartments
before connecting the gas and electrical
supply to the range.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the consumer.
48-1/2"
maximum
36+1/8 ''
f
.....
\
door
closed
maximum
door

Advertisement

loading

Summary of Contents for Electrolux EW3LDF65GSN

  • Page 1 iNSTALLATiON AND SERVICE MUST PERFORMED BY A QUALIFIED iNSTALLER. Refer to your serial plate for applicable iMPORTANT: SAVE FOR LOCAL ELECTRICAL agency certifications iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FUTURE REFERENCE. Provide Proper Fuel Type Before Proceeding: You r range is preset to operate on h P. (Liquified Petroleum) Gas only.
  • Page 2 iMPORTANT SAFETY iNSTRUCTiONS Make sure the wall coverings around the range can Installation of this range must conform with local codes or, withstand the heat generated by the range. in the absence of local codes, with the National Fuel Gas Do not obstruct the flow of combustion air at the Code ANSI Z223.1 --latest edition when installed in the...
  • Page 3: Table Of Contents

    Tools Tools you will need (Wear safety glasses when using tools): For leveling legs and Anti-Tip Bracket: Adjustable wrench or channel lock pliers (Fig. 5). Fig. 8 Fig. 5 1/4" & 5/16" Nutdriver or flat head screwdriver (Fig. 6). Electric drill & 1/8" dia. bit (5/32" Masonry drill bit if installing in concrete (Fig.
  • Page 4 Cabinet and countertop dimensions • Check for wall and cabinet clearances where the range will be installed. Check the stability of the floor where the range will be installed. Check for proper electrical and gas supply. To eliminate the risk of burns Note: All dimensions provided are minimal unless otherwise stated.
  • Page 5: Fig. 23

    Installation with cabinets and wall Anti-tip bracket installation instructions Locate the Bracket Using the Template - (Bracket may be positioned on either the left or right side of the range. Refer to Figs. 24 thru 26 to position the bracket if template is not available).
  • Page 6: Fig. 25

    Anti=tip bracket installation instructions Electrical requirements 3 & 4 - Wire electrical wall Receptacle types & FASTEN BRACKET (WALL OR FLOOR MOUNTING) recommended mounting orientation on wall 1_==1=1/4 ' ' Max. Leveling Leg -- Required for new and remodeled installations Wall M°unt 4-Wire Wall receptacle...
  • Page 7: (Fig. 15)

    Range installations steps Wiring instructions Install the power cord. (4-wire connection - See fig. 33) The rear access cover must be removed. To remove, loosen Before wiring the range review the suggested power center screw (one screw) and remove access cover. The source location drawing in Fig.
  • Page 8: Fig. 33

    Range installation instructions 4-Wire Connection OR _S _ 3-Wire connection instructions (for existing installations ONLY 3 Factory installed connections Connect (DO NOT LOOSEN) See Fig. 34) neutral (white or center) here Terminal Power Cord Connection block Connect Followthemanufacturer'sinstallationinstructions line 1 supplied with the strain relief and install (Also see here Connect...
  • Page 9 Range installations steps FOR 3 & 4-Wire Permanent Connections (3 & 4 - Wire Permanent Connections) Strip insulation away from the ends of the permanent wiring ,_=Tighten all 3 Terminal wire leads for Line 1, Line 2, Neutral (also strip ground wire on 4- block Wire Connections).
  • Page 10 Range installation instructions Do not allow the Pressure Regulator to turn Provide an adequate gas supply. on pipe when tightening fittings. 4.) Attach flexible Appliance Conduit to Flare Adapter on This range is pre-set to operate on 4" natural gas manifold Pressure Regulator (Figs.
  • Page 11 Range installations steps Carefully slide range into cabinet opening. Carefully slide range into cabinet opening while inserting rear leveling leg into and FULLY ENGAGING THE ANTI-TIP BRACKET (See Fig. 26). Make sure that the flexible appliance conduit (Fig. 18) and the power cord (Fig. 20) folds into the remaining open floor area behind the range warmer or storage drawer.
  • Page 12 Inner burner flame Range installations steps Ri__ght-hand burner only_ adjustment screw Test to verify if "LO or LOW" setting should be adjusted (all other positions): Outer burner flame '_I_ Follow steps a thru d above. adustment screw Insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted screw inside.