Advertisement
INSTALLATION
AND SERVICE
MUST BE PERFORMED
BYA QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL
ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE.
Clearances
and Dimensions
1.
Provide adeauate clearances between the range and adjacent combustible surfaces.
2.
Location--Check
location where the ranqe will be installed. Check for proper electrical supply, and the stability of the floor.
3.
Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid
and level.
RANGE
OVERALL
DIMENSIONS
25-3/4"
......... 3o"--.j,,..._
4
/2"
•5/8"**
29-7/8" "'_
-_>
Door Open
\_,""_"
--
- -
WW
Fig,
1
Depthis 28-13/32"withdoor handle.
RANGEELECTRICAL
CONNECTIONS
ii dimensionsfoi
lectricaloutlet location I
re maximum,
j
I_
_Dashedcubedarea
1
_Center,ine showswhere the
|
I
ofrange
electrical outlet must
/
II
I
be installedfor flush to/
I
-_-111",,,the wall installati°n. J
2-5/8" for modelsequipped
with warmerdrawers,
3-1/2" for modelsequipped
withstorage drawers
Fig.
2
FRONT-- TYPICALCABINETINSTALLATION _
SIDE
VIEW
Minimumto
1"4_
wall on either
side of range
above 36" height.
_30"
--_
30"
'k
Minimum
_F
1
t
eithersideMinimumt°
18" cabinetson
®'® _
®'®
_
of range.
Fig. 3
<_
30"
1_-13"-_
Maximumdepth
for cabinets
above range top.
O"clearancebelow cookingtop and at rear of range.
*30" MINIMUM
CLEARANCE
BETWEEN
THE TOP OFTHE
COOKING
SURFACEAND
THE BOTTOM
OFAN
UNPROTECTED
WOOD
OR METAL
CABINET;
OR 24" MINIMUM
WHEN
BOTTOM
OF WOOD
OR M ETAL CABINET
IS PROTECTED
BY NOT LESS THAN
1/4" FLAME
RETARDANT
M ILLBOARD
COVERED
WITH NOT LESS THAN NO. 28 MSG SHEET
STEEL, 0.015" STAINLESS
STEEL, 0.024" ALUMINUM
OR 0.020" COPPER.
0" CLEARANCE
IS THE MINIMUM
FOR THE REAR
OF THE RANGE.
FOLLOW
ALL DIMENSION
REQUIREMENTS
PROVIDED
ABOVE
TO
PREVENT
PROPERTY
DAMAGE,
POTENTIAL
FIRE HAZARD,
AND INCORRECT
COU NTERTOP
AND CABINET
CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED
ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY
INSTALLING
A RANGE HOOD THAT PROJECTS HORIZONTALLY
A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
IMPORTANT
SAFETY
INSTRUCTIONS
• ALL RANGES
CAN TIP
• INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP
DEVICE PACKED WITH
RANGE
• SEE INSTALLATION
INSTRUCTIONS
_'!_lviV-'1_t#ll_[_ll If the information in this manual is not followed
exactly, a fire or electrical shock may result causing property
damage, personal injury or death.
Important
Notes to the Installer
•
Read all instructions contained in these installation instructions
before installing range.
•
Remove all packing material from the oven compartments
before connecting the gas & electrical supply to the range.
•
Observe all governing codes and ordinances.
•
Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructionswith yourowner's guide forfuture reference.
As when using any appliance generating
heat, there are
certain safety precautions you should follow. These are listed
in the Use & Care Guide, read it carefully.
Be sure your range is installed and grounded properly by a
qualified installer or service technician.
Make sure the wall coverings around the range can withstand
the heat generated by the range.
To eliminate the need to reach over the surface elements,
cabi net storage space above the elements should be avoided.
Serial Plate Locations:
Serial
plate Iocatio
Serial
plate is located
on the lower
right front frame
of the appliance.
Alternate
location
may
be under
cooktop.
EspaiSol - P&ginas
5-8
Advertisement
