Related Manuals for Atrix VACBP1
Summary of Contents for Atrix VACBP1
- Page 1 Atrix Back Pack Vacuum OWNER’S MANUAL Model: VACBP1 120V 60Hz 12A, 1400W Atrix International, Inc. 1350 Larc Industrial Blvd. Burnsville, MN 55337 www.atrix.com sales@atrix.com 952.894.6154 Tel 800.222.6154 Toll Free Tel 952.894.6256 Fax...
-
Page 2: Important Safety Instructions
5. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to Atrix International. 6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges of corners. - Page 3 GETTING TO KNOW YOUR BACK PACK VACUUM 1. Main Unit 15. Telescopic Tube 2. Exhaust Grill 16. Waist Band Back Support Panel 3. On/Off Power Switch 17. Waist Band 4. Canister Lid Tabs 18. Dusting Brush...
-
Page 4: Operating Instructions
5. Waist Band 19. Crevice Tool 6. Shoulder Straps 20. Blower Port 7. Back Board Panel 21. Pet Hair Remover 8. Carry Handle 22. Floor to Carpet Brush 9. Hose Inlet 23. Exhaust Filter 10. Canister Lid 24. Blowing Attachments 11. - Page 5 4.Holding the HEPA dust bag in your hand, slide it firmly between the slots in the bag holder. (Fig 2) Fig. 2 Fig. 5 Operating Instructions Attaching the Flexible Hose to 3 To remove the telescopic tube from the Vacuum the flexible hose, pull on the telescopic The flexible hose should be tube and flexible hose handle to pull it out.
- Page 6 Using the Floor to Carpet Brush 1. To attach the floor to carpet brush to Fig. 7 the telescopic tube, insert the telescopic 2 Push forward on the plastic button and tube into carpet to floor brush. (Fig.11) pull the inner tube outward to extend for a longer reach.
- Page 7 Caution: Do not vacuum pet hair. pile or closed for low pile carpets Remove brush on delicate or woven Using the Blower Attachments fabrics that may snag, The blower attachments are extremely Do not use pet hair remover brush on useful for vacuuming in hard to reach crevices wooden floors as this accessory might and small compartments such as in cars.
- Page 8 Fig.14 4. To attach the hose to the blower port,align the flexible hose and turn counter-clockwise until it stops.The hose is now securely in place. (Fig. 15) Fig. 15 Operating Instructions Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust bag, shake-out bag, changing the filters or performing maintenance or trouble- shooting checks.
- Page 9 6. Replace the shake-out bag into the vacuum. 7. To replace the HEPA dust bag holder, flip the holder and press tab until it clicks. 8. Replace the canister lid onto the Fig.19 vacuum. 2. Pull the tab on the HEPA dust bag Warning: Never overfill the HEPA holder out slightly and flip upwards.
- Page 10 more dust. 2. Vigorously “TapClean” the HEPA 2. The shake-out bag is hand wash- pre-motor filter on a hard surface to able in lukewarm water. remove any residual dust that might 3. Allow to air dry for 24 hours. The still be on the HEPA pre-motor filter.
- Page 11 (1) year from the date of purchase. Should any failure to conform to this warranty appear within this period, Atrix will, at its option, repair or replace the defective product.