Page 1
PART NUMBER 350016-0000 RAPID-ROLL DOOR OWNER’S MANUAL MODEL 355 VersionNovember 2006 975-A OLD NORCROSS ROAD LAWRENCEVILLE, GA 30045 (770) 338-5000 TEL (770) 338-5034 FAX (877) 925-2468 TOLL FREE...
Page 2
WARNING DO NOT INSTALL, OPERATE, OR SERVICE THIS PRODUCT UNLESS YOU HAVE READ AND UNDERSTAND THE SAFETY PRACTICES, WARNINGS, INSTALLATION, AND MAINTENANCE INSTRUCTIONS CONTAINED IN THIS MANUAL. Nov. 2006...
Page 4
No other oral or written representations made by Albany Door Systems or its agents are a part of this warranty unless specifically set forth in writing by an authorized Albany Door Systems official.
9. USE EXTREME CAUTION when it is necessary to service the control panel while it is energized. 10. If you have any questions, please contact your local Albany service provider for assistance. Otherwise contact Albany Door Systems at 1-877-925-2468 for information on your local distributor.
PACKING LIST Before beginning the installation, thoroughly inspect the crate to ensure all necessary components are there. The following list applies to a standard Model 355 door (No optional parts are included unless ordered that way). Left Hand and Right Hand Side Columns with attached Covers (1 set)
Page 7
MODEL 355 MECHANICAL INSTALLATION Step 1 . Unpack crate and inventory parts, comparing against the packing list in the front of this manual, to verify all parts are on site. Step 2 . Using a tape measure, determine the clear opening width. Compare this measurement with the door ordered width.
Page 8
Slotted Holes Figure 2 Step 6 . Attach width gauge to the rear of door at both head plates. Removal of the black plastic funnels on the head plates will make installing the width gauge easier along with the routing of the photocell cables.
Page 9
Step 7. Using an approved lifting device, place a lifting strap around the top roll assembly, lift and remove from shipping crate. Raise the top roll assembly into position and lower it slowly onto the top of both side columns. Ensure the bearing housings are located outside the head plates. Secure the top roll at both head plates on each side of door.
Page 10
Step 10 . Attach and place 2 pre-wraps of tensioning rope on both rope pulleys and allow rope to drape down over the front of the side columns. (Figure 4) Special instructions for rope The white rope does not so readily fit into the groove of the take up spool and requires a special step to allow for this.
Page 11
Step 11. Slide the bottom rail profile into the base of the curtain and center. Once the bottom beam is centered, then locate the 2 predrilled holes on each end of profile, drill through the fabric and use the provided slotted screws and acorn nut to secure the bottom beam in place. Step 12 .
Page 13
INSTALLATION OF MANUAL DISENGAGEMENT LEVER TOP ROLL BEARING BRACKET (TOP VIEW) DRIVE UNIT 1. RUN BARE CABLE UP THROUGH SIDE FRAME AND SMALL HOLE IN BEARING PLATE. CABLE SHEATH STARTS HERE. RUN CABLE FROM TOP OF BEARING PLATE OVER TO DRIVE UNIT.
Page 14
THRU-WALL DISENGAGEMENT LEVER INSTALLATION Figure 10 Nov. 2006...
ELECTRICAL INSTALLATION The following instructions are recommended guidelines for electrically installing a typical Model 355 door. Actual wiring may be different based on what options, special instructions, special components, etc. were ordered with the door. Consult the electrical schematics that are supplied with the door. These should be located inside the control panel.
Page 16
FIGURE 11 Label What Plug Location THERMAL SWITCH 3 WIRE BLK. WIRE MOTOR TOP OPEN PROX. 3 WIRE BLK. WIRE SIDE FRAME PHOTOCELL RECEIVER 3 WIRE LEFT SIDE FRAME PHOTOCELL TRANSMITTER 3 WIRE RIGHT SIDE FRAME X37.1 CSE RECIEVER 4 WIRE RIGHT SIDE FRAME X38.1 CSE TRANSMITTER...
Page 17
ELECTRICAL START UP Step 1. Manually bring the door to the halfway closed position. This can be done by pulling down on the bowden lever to release the drive unit brake and moving the curtain by hand (Figure 12). Step 2. Check for correct line voltage at the disconnect with a voltmeter.
Page 18
SETTING DOOR LIMITS NOTE IT IS IMPORTANT TO ENSURE THE DOOR IS MOVING WHEN THE RESET BUTTON IS PUSHED TO SET THE CLOSE LIMIT. DO NOT RELEASE JOG SWITCH UNTIL DOOR HAS STOPPED. Step 1. Press SETUP button. Reset light will turn on; this indicates that you are in the setup mode. Close the door using the OPEN/CLOSE JOG DOOR button.
Page 19
Quick reference for setting limits Reset Light turns on Press SETUP button Close door with ‘JOG’ switch Door starts to CLOSE When door reaches bottom Door in the CLOSED limit, press RESET button POSITION while the door is still moving. Reset Light turns on Press SETUP button OPEN door with ‘JOG’...
MAINTENANCE WARNING REMOVE ALL POWER AT THE FUSED DISCONNECT DURING ALL ELECTRICAL OR MECHANICAL SERVICING. DISCONNECT MUST BE PROPERLY LOCKED OUT DURING MAINTENANCE OR SERVICE OF EQUIPMENT. DAILY INSPECTION Run through a full door cycle (open/close) and ensure smooth operation. Verify that the door is not jammed or hanging up.
Page 22
SRD2™ RESET SYSTEM The Model 355 door comes standard with the SRD2™ self-repair device. The tensioning rope remains attached to the bottom rail profile allowing it to swing away if struck. The tension on the rope will automatically pull the bottom rail back into place. The Contactless Safety Edge™ does need to be reset, however.
Page 23
MODEL 355 TROUBLESHOOTING GUIDE WARNING ENSURE THAT THE POWER LED ON THE FREQUENCY INVERTER IS FULLY EXTINGUISED WHENEVER DE-ENERGIZING CONTROL PANEL TO PERFORM ANY ELECTRICAL WORK (WAIT AT LEAST 30 SECONDS). THIS WILL INDICATE THAT THE HIGH VOLTAGE CAPACITORS HAVE BEEN FULLY DRAINED. FAILURE TO WAIT MAY RESULT IN ELECTRICAL SHOCK.
Page 24
Notes: if the ALARM LED on the frequency inverter is on, call the factory for direction. To clear alarm condition, remove power to control panel. The most common cause of an inverter alarm is a motor current overload condition. Ensure that the door is not jammed in any way and will move freely over the entire range of motion when the motor brake is manually released.
Page 25
Door limits properly set. Gearbox breather plug installed. All actuators tested and function properly. Door has been cycled at least 10 times to verify proper operation. Notes:___________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ FAX COMPLETED FORM TO ALBANY INTERNATIONAL SERVICE DEPARTMENT AT (770) 338-5034. Nov. 2006...
Need help?
Do you have a question about the 355 and is the answer not in the manual?
Questions and answers