Download Print this page

Important Notes To The Installer; Optional Items Available; Important Safety Instructions - Electrolux E36EC75HSS3 Installation Instructions Manual

Electric cooktop

Advertisement

Available languages

Available languages

Important
Notes
to the Installer
1.
Read all instructions contained in these installation
instructions before installing the cooktop.
2.
Remove all packing material before connecting the
electrical supply to the cooktop.
3.
Observe all governing codes and ordinances.
4.
Be sure to leave these instructions with the consumer.
Important
Note
to the
Consumer
Keep these instructions with your Use and Care Guide for
future reference.
Optional
Items
Available:
• A 9" (22.9cm) Stainless Steel Backsplash
Kit #903048-9010
• A Black Knobs Kit #903049-9010
Those kits can be order through
the Service Center at
1-877-4ELECTROLUX
(1-877-435-3287).
However
all cost
related to those kits will be at customer
charges.
I M PORTANT SAFETY
INSTRUCTIONS
• Be sure your cooktop
is installed
and grounded
properly
by a qualified
installer
or service
technician.
• These cooktops
must be electrically
grounded
in
accordance
with
local codes or, in their
absence,
with
the National
Electrical
Code ANSI/NFPA
No.
70--latest
edition
in the United
States,
or with
CSA Standard
C22.1, Canadian
Electrical
Code, Part
1, in Canada.
_The
electrical
power
to the cooktop
must be shut off while
line connections
are being
made.
Failure
to do so could
result
in serious
injury
or death.
Provide
Electrical
Connection
Install the junction
box under tile cabinet
and run 120/
240 or 120/208
Volt, AC wire from the main circuit
panel
NOTE: DO NOT connect
the wire to the circuit
panel at this time. Wait until all wires have been
connected
in the junction
box.
Electrical
Requirements
Observe all governing
codes and local ordinances.
1.
A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (time-
delay fuse or circuit breaker is recommended). DO
NOT fuse neutral
The fuse size must not exceed the
circuit
rating of the appliance
specified
on the
nameplate.
NOTE: Wire sizes and connections
must conform
with
the fuse size and rating of the appliance
in accordance
with
the National
Electrical
Code ANSI/NFPA
No. 70-
latest edition,
or with
CSA standard
C22.1,
Canadian
Electrical
Code,
Part 1, and local local codes and
ordinances.
An extension
cord must not be used
with
this appliance.
Such use may result
in a fire,
electrical
shock, or other
personal
injury.
2.
The appliance should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from this appliance should
be connected directly to the grounded junction box.
The junction box should be located as shown in
Figure 2 with as much slack as possible remaining in
the cable between the box and the appliance, so it
can be moved if servicing is ever necessary.
3.
A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
Unpacking
Instructions
1.
Unpack and visually inspect the cooktop
2.
Be sure the bottle of cleaner conditioner packed in the
literature bag is left where the user can find it easily. It
is important that the ceramic-glass smoothtop be
pretreated before use see Cooktop Cleaning and
Maintenance section in the Use and Care Guide.
Electrical
Connection
It is tile responsibility and obligation of tile consumer to
contact a qualified installer to assure that the electrical
installation
is adequate and is in conformance with the
National Electrical Code ANSI/NFPA No. 70-latest
edition, or with CSA Standard C22.1, Canadian
Electrical Code, Part 1, and local codes and ordinances.
Electrical
ground
is required
on this appliance.
This appliance is equipped with a copper conductor
flexible cable. If connection is made to aluminum house
wiring, use only special connectors which are approved
for joining copper and aluminum wires in accordance
with National Electrical Code and local codes and
ordinances.
This appliance is manufactured with a white neutral
power supply wire and a frame connected green or bare
copper grounding wire.
4

Advertisement

loading