Download Print this page

Frigidaire MFF312HSC Installation Instructions

30" electric range for 2 wire, 50 hz systems
Hide thumbs Also See for MFF312HSC:

Advertisement

INSTALLATION
AND SERVICE
MUST BE PERFORMED
BYAQUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
Clearances
and Dimensions
1.
Provide
adequate
clearances
between
the range and adjacent
combustible
surfaces.
2.
LocationiCheck
location
where the range will be installed.
Check for proper
electrical
supply,
and the stability
of the floor.
3.
Dimensions
that are shown
must be used. Given dimensions
provide
minimum
clearance.
Contact
surface
must
be solid and level.
FRONT
n
0b
¸ ig
!gbli
ii/gii!
h !
i
!
i
i
Minimum to
wall on either
1"_
side of range
above 36" height.
i
Fig. 1
® @
@'®
30"
SIDE
VIEW
Minimum
to
. cabinets on
18
either side
of range.
Maximum depth
for cabinets
above
range
top.l_
0" clearance
below cooking
top and at rear of range
RANGE
OVERALL
DIMENSIONS
Fig. 2
Center',ine
of range
2-5/8" for models equipped
with warmer drawers"
3-1/2" for models equipped
with storage drawers
Fig. 3
Edge
*30" MINIMU M CLEARANCE
BETWEEN THE TOP OF THE
COOKING SURFACE AND THE BOTTOM OF AN
UNPROTECTED
WOOD OR METAL CABINET; OR 24"
MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS
PROTECTED
BY NOT LESS THAN 1/4" FLAME RETARDANT
MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG
SHEET STEEL 0.015" STAINLESS STEEL 0.024"ALUMINUM
OR 0.020" COPPER, 0" CLEARANCE IS THE MINI MUM FOR
THE REAROF THE RANGE. FOLLOW ALL DIMENSION
REQUIREMENTS
PROVIDED ABOVE TO PREVENT
PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND
INCORRECT COUNTERTOP
AND CABINET CUTS.
TO ELIMINATE
THE RISK OF BURNS OR FIRE BY
REACHING OVER HEATED SURFACE UNITS, CABINET
STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS
SHOULD BE AVOIDED. IF CABINET STORAGE
IS TO BE
PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING
A
RANGE HOOD THAT PROJECTS HORIZONTALLY
A
MINIMUM OF 5" BEYOND THE BOTTOM OF THE
CABINETS.
Serial Plate Locations:
Sedan
ilnale nocat_on
Serial plate is located on the lower right front frame of the appliance.
Alternate location may be under cooktop.
pin 316454914(0803)
EspaSol- Paginas 5-8
1

Advertisement

loading

Summary of Contents for Frigidaire MFF312HSC

  • Page 1 INSTALLATION AND SERVICE MUST BE PERFORMED BYAQUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions Provide adequate clearances between the range and adjacent combustible surfaces. LocationiCheck location where the range will be installed. Check for proper electrical supply,...
  • Page 2 IMPORTANT SAFETY INSTRUCTIONS NORMAL INSTALLATION STEPS ANTI-TIP BRACKET INSTALLATION INSTRUCTIONS If the information in this manual is not followed - IMPORTANT SAFETY WARNING exactly, a fire or electrical shock may result causing property To reduce the risk of tipping of the range, the range must damage, personal injury or death.
  • Page 3 2b, MODELS REQUIRING POWER SUPPLY CORD KIT. RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN RELIEF BRACKET IS DISCARDED. This appliance may be connected by means of a power supply cord.
  • Page 4 4a. POWER CORD CONNECTIONS This range must be connected to a power source either with a Power Cord or by Permanent Wire Connections. Follow either step 4a or 4b for electrical connections. Before wiring the range review the suggested power source location drawing in Fig. 3. Follow the manufacturer's installation instructions supplied with the strain relief and install (Also see Figs.

This manual is also suitable for:

Fff384hcaFff384hcbMff312bsfWff334gcbWff334gca