Advertisement
Quick Links
INSTALLATION
AND SERVICE
MUST BE PERFORMED
BY A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL
ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE.
If the information
in this
manual
is not
followed
exactly, a fire or explosion
may result causing
property
damage,
personal
injury or death.
FORYOUR
SAFETY:
--
Do not store or use gasoline
or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
--
WHATTO
DO IFYOU SMELL
GAS:
• Do not try to light any appliance.
• Do not touch any electrical
switch;
do not use any
phone in your building.
• Immediately
call yourgas
supplier from a neighbor's
phone.
Follow the gas supplier's
instructions.
• If you cannot
reach your gas supplier,
call the fire
department.
--
Installation
and service
must be performed
by a
qualified installer, service agency or the gas supplier.
A
V
• ALL RANGES
CAN TIP
• INJURYTO
PERSONS
COULD
RESULT
• INSTALL
ANTI-T1P
DEVICE
PACKED
wn14
RANGE
• SEE INSTALLAllON
INSTRUCTIONS
Note: For appliances
installed
in the
state of Massachusetts
see page 2.
RANGE
OVERALL
DIMENSIONS
253/4 •
44 5/8'
Door Open
MaximumDepth
for Cabinets
AboveRangeTop.
_25!!_
0" ClearanceBelowCooking Top and at Rearof Range.
Clearances
and Dimensions
1.
Location--Check
location where
the range will be installed. Check
for proper
electrical
and gas
supply, and the stability of the
floor.
2.
Dimensions that are shown must
be used.
Given
dimensions
provide
minimum
clearance.
Contact surface must be solid
and level.
PIN 316259329
EN_SP (0309)
Provide
Proper
Fuel Type
Before Proceeding: Your range is preset to operate on natural gas only. Some
models are shipped convertible with parts and conversion
instructions supplied.
Other models have a LP/Propane Conversion Kit available through your dealer.
DO NOT attempt to convert this range to LP/Propane settings without
the proper LP/Propane conversion kit provided with the range or obtained from your
dealer. Follow all instructions provided with the conversion kit.
EspaSol- Pages 9-16
Advertisement
Related Manuals for Frigidaire FGF366ASD
Summary of Contents for Frigidaire FGF366ASD
- Page 1 INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal...
- Page 2 lrl'_lw'-IttPIl_[ 'PIIStepping, leaning or sitting on the doors Important Notes to the Installer ordrawers of this range can result in serious injuries and Read all instructions contained in these installation can also cause damage to the range. instructions before installing range. Remove all packing material from the oven compartments Do not store items of interest to children...
-
Page 3: Before Starting
Locate the Bracket Using the Template - (Bracket may Before Starting be located on either the left or right side of the range. Use Tools You Will Need the information below to locate the bracket if template is For leveling legs and Anti-Tip Bracket: not available). - Page 4 Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: A minimum clearance of 1/8" is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check you r adjustments.
- Page 5 Read electrical connection details below Manual Flare Flexible Flare Union Pressure and connect electricity to range. Shutoff Union Appliance Adaptor Regulator _'lVJV'J:t_ll_[cl Before servicing, disconnect electrical supply at circuit breaker, fuse or power cord. Electric Requirements: An individual, properly grounded and ServiceShut-OffValve ElectricIgnition modelsonly_ (Shownin ON Position).
- Page 6 Electric Ignition Surface Burners Operation of Surface Burners Operation of electric igniters should be checked after range Installation of Burner Cap Assembly and supply line connectors have been carefully checked for Your range is equipped with any combination of the sealed leaks and range has been connected to electric power.
- Page 7 8. Adjustthe "LOW" Setting of Surface Burner After removing all packing materials and literature from the Valve (Linear Flow Valves Only): oven: Set oven to BAKE at 300°F. See Use & Care Manual for operating instructions. Within 60 seconds the oven burner should ignite. Check for proper flame, and allow the burner to cycle once.
- Page 8 If removing the range is necessaryfor cleaning or maintenance, shut off gas supply. Disconnect the gas and electrical supply. If the gas or electrical supply is inaccessible, lift the unit 01_Etri slightly at the front and pull out away from the wall. Pull only Tube as far as necessary to disconnect the gas and electrical supply.