GE Monogram ZEU30R Installation Instructions Manual page 2

gefi)re wmbegin--Read t hese instHictions completely andcarefllllv.
IMPORTANT--Sax e these instructions for local i nspector's u se,
IMPORTANT--OBSERVE ALL GOVERNING C ODES ANDORDINANCES,
Noteto InstaJler--ge s uretoleave these instructions w iththe(hmsumer.
Note to Consumer--Kee I) these inst_ uctions fin" flmu'e reference,
Note--This appliance must be properly grounded.
ATTENTION INSTALLER: ALL COOKTOPS MUST BE HARD WIRED (DIRECT WIRED) INTO
AN APPROVED JUNCTION BOX, A "PLUG AND RECEPTACLE" IS NOT PERMITTED ON
THESE PRODUCTS.
This appliance must be properly grotmded. See "Electrical Connections," page 7.
If you have questions concerning the installation
of this product, call the GE Answer Center _'_
Consumer Inflmnation Service at 800.626.2000,
24 hours a da 5 7 days a week or visit ore" website
at: Monograil/,COIll,
If you received a damaged cooktop, you should
contact vo/Ir
dealer.
I
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance _hrrantv. See
the Owner's Manual for warranty intormation.
For Monogram local service in your area,
1.800.444.1845.
For Monogram Service in Canada,
1.888.880.3030.
For Monogram Parts and Accessories,
call 1.800.626.2002.
FOR YOUR SAFETY:
For Personal Safer), remove house fuse or open
circuit breaker before beginning installation.
Failure to do so could restdt in serious it_juI')
or death.
Be sure your cooktop is installed properl) b) a
qualified installer or service technician.
To eliminate tile risk of burns or fire b) reaching
over heated surfime elements, cabinet storage
located above the sm'f_me traits should be axoided.
If cabinet storage space is to be provided, the risk
can be reduced b) installing a range hood that
projects horizontall_ a minimmn of 5" beyond tile
bottom of the cabinets. Cabinet installation above
tile cooktop ma) be no deeper than 13".
• Make sm'e tile cabinets and _dl coverings arotmd tile
cooktop can withstand the temperatures (u t) to 200°F)
generated b) the cooktop.
• Tile cooktop shouM be eas) to reach and lighted with
natural light dm'ing the day.
• Always discomlect the electrical service to the cooktop
before repairing or servicing the cooktop. This can be
done b) discomlecting the fuse or circuit breaker:
Failm'e to do this cotdd result in a dangerous or fatal
shock. Know where )ore" main disconnect switch is
located. If )ou do not know, hme your electrician
show }OIA,
Check local building codes fin" the proper method
of cooktop installation, i,ocal codes vary. Installation,
electrical connections and grotmding must comply
with applicable codes.
2
Electrical Requirements
This appliance must be supplied with tile proper voltage and fl'equency, and c(mnected to an
individual, properl) grotmded branch circuit, promcted b) a circuit breaker or a time delay fl_se as noted
on the rating plate.
_,\_ recommend you have tile electrical wiring and hookup of your cooktop c(mnected by a qualified
electrician. After installation, have the electrician show )ou _d_ere yore" main range disc(mnect
is located.
Wiring must contbrm to the National Electrical Code. Y)u can get a cop} of the National Electrical Code,
ANSI/NFPA No. 70-Latest Edition, b) _Titing:
National Fire Protection Associatkm
Batter}march Park
QIIJI1c}_
MA 02269
Tile cooktop conduit wiring is approved ti)r copper wire ccmnection onl) and if you have almninum house
wiring, )ou must use special UL approved comlectors tbrjoining copper to aluminmn.
You must use a two-wire, three conductor 208/240VAC, 60 Hertz electrical system. A white (neutral) wire
is not needed ti)r this trait. The cooktop must be installed in a circuit that does not exceed 125 VAC nominal
to grotmd. Refer to the rating plate on yore" cooktop fin" the KW rating ti)r yore" cooktop.