Related Manuals for GE ZBD 5600
Summary of Contents for GE ZBD 5600
- Page 1 GE Monogram ® Installation Instructions with Optional Trim Kit Installation Instructions Built-In Dishwashers Modd._ ZBD 5600 ZBD5700 ZBD 5 900...
- Page 2 See tile Use & Care placed as necessary. Guide for warranty infln'mation. If vou have a question concerning tile installa- tion of this product, call tile GE Answer (:enter ® Consmuer hfformation Service • This dishwasher must be installed to allow 800.696.9000,...
- Page 3 Design Information Stai,less Steel I, terior Dishwasher,s ZBD5600 WW, ZBD5700 Models White Dishwashers Available ZBD5600 BB, ZBD5700 Black Dishwashers ZBD5900 Stainless Steel Dishwasher These dishwashers designed versatility, adaptable to virtually installation. These models have a hill length trimless door without the traditional access panel,...
- Page 4 Design Inff)rmation SlaDde,s,_ Sled l_Herior Di,_hwa,_her,_ Cabinet Standard • Install in standard 24" deep cabinets: Resting - The dishwasher door will be flush with AgainstWall installation front thce of ac!jacent cabinetry. • With a 3/4" thick custon_ door panel in 24" de@ place, exterior is trimless...
- Page 5 Installation hdbrmation Slai_less Steel Interior Dishwasher,_ Parts Remove hardware accessory other parts fl'om inside or taped to the Supplied outside of the dishwasher. Check contents against drawings to insure that all parts included. 2 toekick slides 2 teekick support brackets 2 side trim pieces 2-piece teekick 16 Screws (see illustration}...
- Page 6 Installation Preparation Slai_le,s,_ Sleel I_lerior l)i,shwa,_her MateriaLs You %° elbow (3/8" NPTexternal thread on one end and opposite end to fit hot water supply line) Will Need: Thread seal tape Electrical Cable (not supplied) UL listed wire nuts (3) or Power Cord 90°...
- Page 7 Installation Preparation Slai_le,_,_ Sled I_Herior l)i,_hwa,sher • The rough cabinet opening must be 24" rain. deep, 23-5/8" rain. to 24" max. wide. opening height should be 34" rain. ThisWallArea _5" II/ax, mustbeFree i Openin, g Pipes orWires • The opening should be fl'ee of extraneous 34"to35"...
- Page 8 Installation Preparation Slai_le,_,_ Steel I_Herior Di,_hwa,_her,s FORPERSONAL S AFETY: REMOVE H OUSE FUSE OROPEN ..CIRCUIT B REAKER BEFORE BEGINNING Receptacle t \\ INSTALLATION. Alternate Location DONOT USE AN EXTENSION CORD OR ADAPTER P LUG WITHTHISAPPLIANCE FOLLOW NATIONAL E LECTRICAL CODES ORPREVAiLiNG LOCAL C ODES ANDORDINANCES.
- Page 9 Installation Preparation Slai_le,_,_ Sled I_lerior Di,_hwa,sher • Follow local codes and ordinances. Method 1 - Air Gap with Waste Tee or Disposer • Dishwasher drain hose must not exceed Usethis methodwhen waste tee or disposer connection is less drain than 12" above the floor. feet in length for proper drainage.
- Page 10 Installation StaD_le,s,_ Steel I_Herior Di,_hwa,_her • If you intend to install custom door panels, hi, stall Custom refer to installation instructions provided Door Panel this booklet. The panels should be in place beIore installing the dishwasher. Step l shipping carton use it as a pad trader dishwasher,...
- Page 11 Installation Slai_le,vs Sleel I_lerior Di,shwa,sher • Install the 90 ° elbow onto the water inlet. Step 3 Use thread sealing tape or pipe thread Install C()IIlp()/lI1 Water Inlet • The 90 ° elbow should tace the left or right side, depending on water line routing.
- Page 12 Installation StaD_le,s,_ Steel I_lerior Di,_hwa,_her Step 5 • Careflllly upright tile dishwasher, taking care not to bend tile leveling legs. Make Level Level sure tile leveling leg locking nuts are Dishwasher sectlre. Sides • Check to be sure tile dishwasher is level and at tile cutout height.
- Page 13 Installation Slaiule,vs Sleel Iulerior Di,shwa,sher • Follow all local codes ordinances. Method1 - Air Gapwith WasteTee or Disposer Step 8 Drain Line Preparation [nstall • The dishwasher is supplied with a 78" hmg Drain Line corrugated drain hose. • If the location requires a longer...
- Page 14 Installation Stai_less Steel I_Herior Dishwasher To maintain position and alignment Step 10 dishwasher nlust be secured to tile COUlltertop 5 cure or to a(!jacent cabinetry. Dishwasher If co/mtertop is of stone or other hard material, secure the dishwasher to a(!jacent to Countertop cabin ets.
- Page 15 Installation Slai_le,s,s Sleel I_lerior l)i,shwa,sher FrontToel<icl< P anel Step l l • Install toekick slides to toekick support brackets. Use slide stamped "L" on left and [nstall "R" on right side. 7bekick • Align fl'ont ironer toekicks, matching screw holes. Assembly •...
- Page 16 ZPF25 Custom Door Panel l/4" Tkick (u,slom Door Pa_el Moto: It is best that 2 peopleperformthis installation. 7, 5 ZPI_2r B, Black trim ZPF2, White trim ZPF25 trim kit provides support for 1/4" thick custoln door panel. Tools and Materials required •...
- Page 17 ZPF25 Custom Door Panel l/4" Tkick (ustom Door Pa_el • Open the door fllllv., Step 2 Remove Caution: person should hold the door while the other backs out s('rex_s to prex eat Existin, g the metal door fron/falling. Metal Door •...
- Page 18 ZPF25 Custom Door Panel l/4" Tkick Custom Door Pa_el Step 5 • Locate "(7' clips in the parts package. Place clip, flat side tip, oxer each of the fnstall screw holes, 3 on each side of the door. As sembled Note: One personshould hold the door while the other installs Door onto...
- Page 19 ZPF75 Custom Panel Thick (usi0m l)oor Panel ZPF75B, Black Note: It is best that 2 people perform this installation. ZPF75_, _ hite ZPF75 provides fin" the installation 1/2" to 3/4" thick custom door panel. Tools and Materials mqu#ed • Phillips screwdriver Noto: Maximumcustompanelweight is •...
- Page 20 ZPF75 Custom Panel Thick ( u,stom Door Panel Step 2 • Open tile door flflly. Remove Caution: One person should hold the door while the other 2 "0" Rings hacks out screws to preventthe metal door from falling. Existing Metal Door •...
- Page 21 ZPF75 Custom Panel 3/4" Thick Custom Door Pa_el Note: One personshould hold the door while the other installs Step screws to preventthe door assemblyfrom falling. 2 "0" Rings_ hi, stall • Check to be sure that fl)am inserts As s embled i Insert place.
- Page 22 ZPF75 Custom Panel 3/4" Thick ( ustom Door Pa_el • Slip toekick slides into guides by pulling Step 7 the metal tabs. fnstall • Hold custom panel against toekick slides and mark screw hole locations. Custom • Remove toekick and drill 1/8"...
- Page 23 Notes Slai*_le,s,s Sleel I_lerior l)i,shwa,sher 9 °...
- Page 24 (;ene_ Pub. 49-5860-1 Eleclric There,>re, male_ials_ appearance aJ_d specilicalions Primed in USA Monogram: subiecl Io cha_+ge will_<>_l J_olice 4, 1999 GE Appliarlces (N.D. 458) 9/99 Part Number: 0017x General Electric Company Issue Louisville, KY40225...