Advertisement
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip
Bracket
Range Foot
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Tape measure
•
Flat-blade screwdriver
•
Phillips screwdriver
•
Level
•
Hand or electric drill
•
Hammer
•
Wrench or pliers
•
Pipe wrench
•
18/16" c ombination
wrench
•
1¼,drive ratchet
•
3/8"nut driver
•
V8" (3.2 mm) drill bit (for
wood floors)
•
Marker or pencil
•
Pipe-joint compound
resistant to LP gas
•
Noncorrosive leak-detection
solution
For LP/Natural
Gas
Conversions
•
3/8"combination
wrench
•
1/2"combination
wrench
•
8/8"combination
wrench
•
7
mm
(9_32")
nut driver
•
Quadrex ®t or Phillips
screwdriver
•
Masking tape
Parts supplied
Check that all parts are included.
B\
A. Anti-tip bracket
B. #12 x 1 _" screws (2)
•
Anti-tip bracket must be securely mounted to floor or wall.
Thickness of flooring may require longer screws to anchor
bracket to floor.
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements"
and
"Gas Supply Requirements"
sections.
I
,i ;.>_iil
;_I_I_A_II
.xlI+l
@141s+
i
II+I,/I
IMPORTANT: Observe all governing codes and ordinances.
Do
not obstruct flow of combustion
and ventilation air.
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located on the oven frame behind
the top left side of the oven door.
Recessed installations must provide complete enclosure of
the sides and rear of the range.
All openings in the wall or floor where range is to be installed
must be sealed.
Do not seal the range to the side cabinets.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see "Install Anti-Tip Bracket"
section.
•
Grounded electrical supply is required. See "Electrical
Requirements"
section.
•
Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
•
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
•
Use an insulated pad or 1¼,, ( 0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance
with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures
of 194°F (90°C).
1-@QUADREX
is a registered
trademark of NLW Holdings, inc.
Advertisement
