Page 1
This Owner's Manual is provided and hosted by Appliance Factory Parts. Haier CPF12XHLUVB Owner's Manual Shop genuine replacement parts for Haier CPF12XHLUVB Find Your Haier Air Conditioner Parts - Select From 735 Models -------- Manual continues below part list --------...
Page 2
Available Replacement Parts for Haier CPF12XHLUVB P67904053 HEAT EXT HOSE, 5" diameter WJ20X24139 CAPACITOR WJ76X24143 USE NLA ITEM BASE - PAN WJ88X22344 USE NLA ITEM CONDENSER FAN MOTOR AC-1900-089 CORD - Power. Black WJ65X23782 PLATE WJ65X23757 PLATE - WINDOW NO HOLES...
Page 11
>a__WcU[S^ <[c >a`V[e[a`Wc 2. Specifications 2.1 Specifications for inverter units item Model AB182ACERA cooling heating Function Capacity 5.0 1.8--5.8 5.2 2.0---6.2 Sensible heat ratio 0.71 Total power input 1660 550---2400 1730 600---2300 Max. power input 2650 2650 3.01 3.01 EER or COP Dehumidifying capacity 10 ³×m³/h A / A...
Page 12
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD182AMERA Function cooling heating Capacity 5.1 1.8---6.0 6.0 2.0---7.1 0.75 Sensible heat ratio Total power input 1580 550---2650 1650 600---2650 Max. power input 2650 2650 EER or COP 3.23 3.64 Unit model (color) AD182AMERA(WHITE) Type × Number cross flow*1 1150/1050/860/680R/MIN Speed(H-M-L)
Page 13
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU182AFERA Power cable 3G 4.0mm2 Power source N, V, Hz 1, 220--230, 50 Start Current Circuit breaker WHITE Unit model (color) Model / Manufacture TNB175FLBM1/MITSUBISHI ELECTRIC Oil model MEL56 Compressor Oil charging 670ML scroll type Type axial×1 Type ×...
Page 14
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AB242ACERA cooling heating Function Capacity 7.0 2.0---8.0 7.8 2.5--8.5 0.72 Sensible heat ratio Total power input 2300(500---3250)W 2.25(500---2750)W Max. power input 3300W 3300W 3.04 3.46 EER or COP Dehumidifying capacity 10 ³×m³/h A / A 11.0(2.5--14.5 10.0(2.5--12.0 Running /Max.Running current...
Page 15
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD242ALERA Function cooling heating Capacity 7.35 2.0---8.2 8.15 3.0---9.0 0.72 Sensible heat ratio Total power input 2280(600---3250)W 2250(600---3250)W Max. power input 3300W 3300W EER or COP Running /Max.Running 10.0(2.5--14.5)A / 10.0(2.5--14.5)A / A / A current 15.0A 15.0A...
Page 16
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU242AGERA Power cable 3G 4.0mm2 1PH,220-230VAC,50HZ Power source N, V, Hz Start Current WHITE Unit model (color) Model / Manufacture TNB175FLBM1 MITSUBISHI MEL56 Oil model Compressor 670ML Oil charging Type Rotary axial×1 Type × Number Speed r/min 910±30...
Page 17
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AB362ACERA Function cooling heating Capacity Btu/h 33800 38200 Capacity 9.9(2.2~11.6) 11.2(2.5~12.0) 0.73 Sensible heat ratio Total power input 3290(650---3800) 3280(650---3800) Max. power input 4300 4300 3.01 3.09 EER or COP Energy efficiency stage Dehumidifying capacity 10 ³×m³/h 14.3(2.9-17.0)/19.3 14.3(2.9-17.0)/19.3...
Page 18
>a__WcU[S^ <[c >a`V[e[a`Wc AD362AMERA item Model cooling heating Function Capacity BTU/h 32400 38000 Capacity 9.5(2.2~10.8) 11.0(2.5~12.0) 0.73 Sensible heat ratio Total power input 3280(500---3900) 3430(500---3900) 4300 4300 Max. power input 3.21 EER or COP Energy efficiency stage Dehumidifying capacity 10 ³×m³/h 14.3(2.3-17.5)/19.3 15.0(2.3-17.5)/19.3 A / A...
Page 19
>a__WcU[S^ <[c >a`V[e[a`Wc Item Model AU362AHERA 3*4.0 Power cable 1, 220-230, 50 Power source N, V, Hz Start Current AU362AHERA WHITE Unit model (color) TNB220FLBM/MITSUBISHI Model / Manufacture Compressor Rotary Type axial*1 Type × Number 950r/min±50 r/min Speed 0.06 Fan motor output power 4000/-/- Air-flow(H-M-L) m³/h...
Page 20
>a__WcU[S^ <[c >a`V[e[a`Wc 2.2 Specifications for fix frequency unit item Model AB182ACEAA cooling heating Function 17000 18000 Capacity BTU/h Capacity 1780 1550 Total power input Max. power input 2050 1950 2.81 3.41 EER or COP cooling: 7.5A /10.5A heating: 7.0A /10.0A Running /Max.Running current A / A Unit model (color)
Page 21
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD182ALEAA cooling heating Function 18000 18500 Capacity BTU/h 5.17 5.38 Capacity 1720 1580 Total power input 2000 1950 Max. power input 3.01 3.41 EER or COP cooling: 7.8A /9.5A heating 7.3A /9.3A Running /Max.Running current A / A Class 1 Class of anti electric shock...
Page 22
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AB242ACEAA cooling heating Function 7.25 Capacity 0.72 Sensible heat ratio Total power input 2400 2300 3100W 3000W Max. power input 3.02 3.22 EER or COP Dehumidifying capacity 10 ³×m³/h 11.0A/13.9A 10.5A/13.4A A / A Running /Max.Running current grey Unit model (color) centrifugal fan*1...
Page 23
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD242ALEAA cooling heating Function 7.25 Capacity 0.72 Sensible heat ratio Total power input 2400 2300 3100W 3000W Max. power input 3.02 3.30 EER or COP Dehumidifying capacity 10 ³×m³/h 11.0A/13.9A 10.5A/13.4A A / A Running /Max.Running current grey Unit model (color) centrifugal fan*2...
Page 24
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU242AGEAA H05RN-F 3G 4.0mm2 Power cable Power source N, V, Hz 1PH,220-230VAC,50HZ WHITE Unit model (color) Model / Manufacture PA290X3CS-4MU1 TOSHIBA Oil model VG74 Compressor 950ML Oil charging Rotary Type Type × Number axial×1 1000±50 Speed r/min 0.06...
Page 25
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU282AHEAA/AB282ACEAA Function cooling heating Capacity BTU/h 28000 30000 Capacity Sensible heat ratio 0.72 2700 2740 Total power input Max. power input 3400W 3500W 3.04 3.21 EER or COP Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 12.0A/15.0A 12.2A/15.5A A / A...
Page 26
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU282AHEAA/AD282AMEAA cooling heating Function Capacity BTU/h 28000 31000 Capacity 0.72 Sensible heat ratio Total power input 2820 2800 Max. power input 3500W 3500W 3.01 3.25 EER or COP Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 12.0A/15.5A 12.0A/15.5A A / A...
Page 27
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU282AHEAA WHITE color Power cable H05RN-F 3G 4.0mm2 Power source N, V, Hz 1PH,220-230VAC,50HZ NN33VAAMT(MITSUBISHI Model / Manufacture Oil model FV50S Compressor 1300CC. Oil charging Type Rotary Type × Number axial×1 920±50 Speed r/min Fan motor output power 0.06 Air-flow(H-M-L) m³/h...
Page 28
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU28NAHEAA/AB282ACEAA cooling heating Function Capacity BTU/h 28000 29000 Capacity Sensible heat ratio 0.72 Total power input 2800 2600 Max. power input 3500 3500 2.93 3.23 EER or COP Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 4.7A/5.6A 4.6A/5.5A A / A...
Page 29
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU28NAHEAA/AD282AMEAA cooling heating Function Capacity BTU/h 28000 31000 Capacity Sensible heat ratio 0.72 Total power input 2800 2650 Max. power input 3500 3500 3.04 3.40 EER or COP Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 4.7A/5.6A 4.6A/5.5A A / A...
Page 30
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU28NAHEAA H05RN-F 3G 4.0mm2 Power cable Power source N, V, Hz 3PH,380-400VAC,50HZ 33A/36A 33A/36A Start Current Unit model (color) AU28NAHEAA(WHITE) Model / Manufacture NN33YCAMT MITSUBISHI Oil model FV50S Compressor 1300CC. Oil charging Type Rotary axial×1 Type ×...
Page 31
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU362AIEAA/AB362ACEAA Function cooling heating 10.5 Capacity Sensible heat ratio 0.72 Total power input 3300 3500 Max. power input 3900 3950 EER or COP 3.03 B 3.00 B Running /Max.Running current A / A 15.8A/18.5A 16.5A/18.7A AB362ACEAA Unit model (color) Type ×...
Page 32
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU362AIEAA/AB362ACEAA cooling heating Function Capacity 10.5 0.72 Sensible heat ratio Total power input 3300 3500 Max. power input 3900 3950 EER or COP 3.03 B 3.00 B Running /Max.Running current A / A 15.8A/18.5A 16.5A/18.7A Unit model (color) AB362ACEAA Centrifugal fan*1...
Page 33
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU362AIEAA/AD362AMEAA Function cooling heating Capacity 10.5 0.72 Sensible heat ratio Total power input 3400 3500 Max. power input 3900 3950 3.09 3.15 EER or COP Running /Max.Running current A / A 16.0A/18.5A 16.5A/18.7A AD362AMEAA Unit model (color) Type ×...
Page 34
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU362AIEAA Dehumidifying capacity 10 ³×m³/h Power cable H05RN-F 3G 4.0mm2 1PH,220-230AC,50HZ Power source N, V, Hz Start Current 88/96 88/96 NN40VAAMT Model / Manufacture FV50S Oil model Compressor Oil charging 1300cc Rotary Type Type × Number axial×2 Speed r/min...
Page 35
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU36NAIEAA/AB362ACEAA cooling heating Function Capacity 11.5 0.72 Sensible heat ratio Total power input 3800 3900 Max. power input 4700 4800 3.03 3.08 EER or COP Running /Max.Running current 6.4A/8.0A 6.5A/8.0A A / A Unit model (color) AB362ACEAA Centrifugal fan*1 Type ×...
Page 36
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU36NAIEAA/AD362AMEAA cooling heating Function Capacity 12.5 0.72 Sensible heat ratio Total power input 3650 4300 Max. power input 4700 4800 3.01 2.91 EER or COP Running /Max.Running current A / A 6.4A/8.0A 7.3A/8.0A AD362AMEAA Unit model (color) Type ×...
Page 37
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU36NAIEAA Dehumidifying capacity 10 ³×m³/h Power cable H05RN-F 3G 4.0mm2 3PH,380-400AC,50HZ Power source N, V, Hz Start Current 46.3/48.2/50.0 46.3/48.2/50.0 AU36NAIEAA Unit model (color) Model / Manufacture JT125G-P8Y1 DAPHNE FVC68D Oil model Compressor Oil charging 1500cm³...
Page 38
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AU42NALEAA/AP422ACEAA Function cooling heating Capacity BTU/h 42000 47800 Capacity 12.3 14.0 Sensible heat ratio Total power input 4800 5050 6550 Max. power input 5650 2.55 EER or COP Dehumidifying capacity 10 ³×m³/h Power cable section 5G×2.5mm Signal cable section...
Page 39
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AB482ACEAA cooling heating Function 13.6 16.5 Capacity 0.72 Sensible heat ratio 4500 5000 Total power input Max. power input 5500 6000 EER or COP 3.02 B 3.3 C Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 8.0A/9.5A 9.0A/10.5A A / A...
Page 40
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD482AMEAA cooling heating Function 14.06 17.5 Capacity 0.72 Sensible heat ratio 4600 4800 Total power input Max. power input 5500 6000 EER or COP 3.06 B 3.65 A Dehumidifying capacity 10 ³×m³/h Running /Max.Running current A / A 8.0A/9.5A 8.5A/10.5A...
Page 41
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AP482AKEAA cooling heating Function 13.6 16.0 Capacity 0.72 Sensible heat ratio 4500 5250 Total power input Max. power input 5500 6000 EER or COP 3.02 B 3.05 D Dehumidifying capacity 10 ³×m³/h Running /Max.Running current 8.0A/9.5A 9.0A/10.5A A / A...
Page 42
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AB602ACEAA cooling heating Function 15.5 18.5 Capacity 0.72 Sensible heat ratio 5100W 5350W Total power input Max. power input 6200W 6200W EER or COP 3.02 B 3.44 B Dehumidifying capacity 10 ³×m³/h 9.0A/10.5A 9.5A/10.5A A / A Running /Max.Running current Start Current AB602ACEAA black)
Page 43
>a__WcU[S^ <[c >a`V[e[a`Wc item Model AD602AHEAA cooling heating Function 16.1 18.7 Capacity 0.72 Sensible heat ratio Total power input 5350W 5100W Max. power input 6200W 6000W 3.01(B) 3.67(A) EER or COP Dehumidifying capacity 10 ³×m³/h A / A 9.5A/10.5A 9.0A/10 Running /Max.Running current Start Current Unit model (color)
Page 44
>a__WcU[S^ <[c >a`V[e[a`Wc Installation state: the unit should be placed on the flat floor or be mounted in horizontal direction. Testing method: standing-on-floor unit: If the unit cooling capacity is over 28000W, the noise level should be measured at mounting-on-ceiling unit: the front, left, right directions respectively.
Page 45
>a__WcU[S^ <[c >a`V[e[a`Wc outdoor unit: 1.air outlet from side: the noise level is the average sound pressure level measured from front, left, right directions. 2.air outlet from top: the noise level is the average sound pressure level measured from front, back, left, right directions. measured point: H ( height to the ground) = (h (unit height) + 1m) /2 and, it is 1m to each side.
Page 67
>a__WcU[S^ <[c >a`V[e[a`Wc Installation tools The installation tools listed in the following sheet can be used as required. 1. Screw driver 8. Knife 2. Hacksaw 9. Pincers 3. Drill with a diameter of 60mm 10. Leakage detector or soapy water 4.
Page 68
>a__WcU[S^ <[c >a`V[e[a`Wc Preparation for the installtion (1) Position of ceiling opening between unit and suspending bolt. (For series 182) Overlap between ceiling and ornament panel shall be 25mm Suspending bolts Distance between Ornament panel suspending bolts 535mm Ceiling Indoor unit 570mm Ceiling opening 650mm Ornament panel 700mm For series 482,602...
Page 69
>a__WcU[S^ <[c >a`V[e[a`Wc Installation of indoor unit In the case of new ceiling (1) Install unit temporally Put suspending bracket on the suspending bolt. Be sure to use nut and washer at both ends of the bracket. As for the dimensions of ceiling hole, see paper pattern. Ask your real estate dealer for details. Center of the hole is marked on the paper pattern.
Page 70
>a__WcU[S^ <[c >a`V[e[a`Wc Refrigerant piping (As for outdoor piping, please refer to installation Manual of outdoor unit.) Outdoor is precharged with refrigerant. Be sure to see the Fig.1, when connecting and removing piping from unit. For the size of the flare nut, please refer to Table 1. Apply refrigerant oil at both inside and outsid of lflare nut.
Page 72
>a__WcU[S^ <[c >a`V[e[a`Wc (2) Check if water drainage is smooth after installation. For series 242, 282, 362, 482, 602 Charge, through air outlet or inspecting hole, 1200ccd water to see water drainage. After wiring Check water drainage in cooling operation. When wiring is not complete Remove cover of control box, connect 1PH power to terminal 1 and 2 on terminal block.,use remote controller to operate the unit.
Page 73
>a__WcU[S^ <[c >a`V[e[a`Wc Wiring All supplied parts. materials and wiring operation must in appliance with local code and regulations. Use copper wire only. When make wiring, please refer to wiring diagram also. All wiring work must be done by qualified electricians. A circuit breaker must be installed, which can cut power supply to all system.
Page 74
>a__WcU[S^ <[c >a`V[e[a`Wc 2. Mounting on high ceiling (1) Ornament panel can be mounted on ceiling as high as 3 m. (2) Please install pad as accessary. Cut open the pad along cutting ling. Use part a only and discard part b . (Refer to Fig. 4) Install part a of the pad on the place shown in Fig.
Page 75
>a__WcU[S^ <[c >a`V[e[a`Wc 4. Installation of inlet grill and cover plate Installation of inlet grill Install in reversed order of "Prepare ornament pandl". Inlet grill can be adjusted into four directions by turning inlet grill. Inlet grill position can be adjusted as per customers request.
Page 76
>a__WcU[S^ <[c >a`V[e[a`Wc 6.2 Convertible indoor unit (AC18-AC24) Standard accessories: Accessory parts Qty. The following installation parts are furnished. Use them as required. Remote controller Battery Wire clamp Heat insulation sheathing Screw Screw cap Remote controller bracket Pipe connection requirement Please refer to the specification to confirm the stop valve diameter and the permitted pipe drop and pipe length.
Page 77
>a__WcU[S^ <[c >a`V[e[a`Wc (Fig. 4) (Fig. 5) 99cm Wall 24.5cm 50cm Wall bracket 10cm Side of set Indoor unit outdoor unit 6.5cm 7cm hole For series 14,18,24 when installing set to wall, install 3.5cm hole the accessory wall bracket at the position shown in Fig.5,and mount the set to it.
Page 78
>a__WcU[S^ <[c >a`V[e[a`Wc 1. DRILLING FOR PIPING Select piping and drain directions. (Fig.11) (Fig. 11) Rear (Install the drain hose in the direction.) Right CAUTION Install the drain hose at the rear; it should not be installed on the top or right side. 2.
Page 79
>a__WcU[S^ <[c >a`V[e[a`Wc (Fig. 15) Hex bolt 8 to 13mm Indoor unit (Fig. 16) Apply the indoor unit to the brackets.(Fig.16) Bracket Bolt Indoor unit Now, securely tighten the hex bolts in both sides. 5. INSTALL THE DRAIN HOSE Select whether the drain hose will be connected to the left or right side.(Fig.3) Insert the drain hose into the drain pan, then secure the drain hose with a nylon fastener.(Fig.6) Wrap the insulation (drain hose)around the drain hose connection.(Fig.7) Be sure to arrange the drain hose correctly so that it is leveled lower than the drain hose connecting port of the...
Page 80
>a__WcU[S^ <[c >a`V[e[a`Wc B. For strand wiring(Fig.19B) (1) Cut the wire with a wire cutter or wire-cutting pliers, then strip the insulation to about 10mm of the exposed strand wiring. (2) Using a screwdriver, remove the terminal screw(s)on the terminal board. (3) Using a round terminal fastener or pliers, securely clamp a round terminal to each stripped wire end.
Page 81
>a__WcU[S^ <[c >a`V[e[a`Wc ELECTRICAL REQUIREMENT (3) Remove the electric component box cover. Electric wire size and fuse capacity: Fig. 24 Type For series 182 For series 242 Connection cord 0.75 0.75 Power supply cord (mm Fuse capacity(A) Base Electric component box cover 1.
Page 82
>a__WcU[S^ <[c >a`V[e[a`Wc ELECTRICAL WIRING (2) Air filter removal and cleaning, and how to use air louvers. WARNING (3) Give the operating and installation manuals to (1) Always use a special branch circuit and install a special the customer. receptacle to supply power to the room air conditioner. MOUNT THE COVER PLATE AND (2) Use a circuit breaker and receptacle matched to the capacity of the room air conditioner.
Page 83
>a__WcU[S^ <[c >a`V[e[a`Wc 6.3 Convertible indoor unit (AC28-AC60) Please ask the dealer or specialist to install, never try by the users themselves. After the installation please be sure of the following conditions. WARNING ! Please call dealer to install the air-conditioner. Incorrect installation may cause water leaking, shock and fire hazard.
Page 84
>a__WcU[S^ <[c >a`V[e[a`Wc (5) Also, do not use an extension cord. (6) Plug in the power cord plug firmly. If the receptacle is loose, repair it before using the air conditioner. (7) Do not turn on the power until all installation work is done. Be careful not to scratch the room air conditioner when handing it.
Page 85
>a__WcU[S^ <[c >a`V[e[a`Wc Ceiling panel 0.4"(10mm) over ACCESSORIES Optional parts Standard accessories: Ceiling panel Mark Parts name Accessory parts Remarks Qty. Adhesive tape Saddle (L.S) with screws Drain hose Remote controller Heat insulation material Piping hole cover Battery Putty Plastic clamp Wire clamp Heat insulation...
Page 86
>a__WcU[S^ <[c >a`V[e[a`Wc 2) LOCATION OF CEILING SUSPENSION BOLTS Fig. 3 30mm 30mm Dimensions (Space Required for Suspension bolt pitch 1530mm installation) 10mm Suspension bolt should extend outward 30 to 50mm. 155mm INDOOR UNIT (TOP VIEW) 300mm For half-concealed installation Supension-bolt pitch should be as shown in Fig.4.
Page 87
>a__WcU[S^ <[c >a`V[e[a`Wc INSTALLING THE INDOOR UNIT (1) Lift unit so that suspension bolts pass through suspension fittings at the sides (four places),and slide the unit back.(See Fig.8.) Fig. 7 Fig. 8 Ceiling Ceiling panel Wall Wall (2) Fasten the indoor unit into place by tightening-up the special "B",blots and the M10 nuts. Make sure that unit is secure and willl not shift back and forth.
Page 88
>a__WcU[S^ <[c >a`V[e[a`Wc Coupler heat insulation(large) Fig. 10 Coupler pipe (large) Indoor unit Coupler pipe (small) Coupler heat insulation(small) Nylon fastner (large) No gap Indoor unit Coupler heat insulation Nylon fastner (small) When using an auxiliary pipe, make sure that the fastener used is insulated in the sane way. DRAIN PIPING Install the drain pipe with downward gradient (1/50 to 1/100) and so there are no rises or traps in the pipe.
Page 89
>a__WcU[S^ <[c >a`V[e[a`Wc (1) Install insulation for the drain pipe.(See Fig.12 and 13) Cut the included insulation material to an appropriate size and adhere it to the pipe. Fig. 12 Drain pipe Insulation for Drain pipe (To be obtained locally.Length shoud be at least 8mm) Drain pipe insulation Indoor unit(drain port)
Page 90
>a__WcU[S^ <[c >a`V[e[a`Wc Fig. 15 B. Strand wire A. Solid wire Round terminal Loop Insulation Screw with special washer Screw with Round special washer terminal Round Terminal terminal block Wire Wire HOW TO FIX CONNECTION CORD AND POWER CABLE AT THE CORD CLAMP After passing the connection cord and power cable through the insulation tube, fasten it with the cord clamp, as shown in Fig.16 ELECTRICAL REQUIREMENT...
Page 91
>a__WcU[S^ <[c >a`V[e[a`Wc FRESH-AIR INTAKE (1)Take away the knockout hole for the fresh-air intake,as shown in Fig.17.(If using half-concealed installation ,take down the top knockout hole instead) Fig. 17 For half-concealed CAUTION (1)When removing the cabinet(iron plate),be careful not to damage the indoor unit internal parts and surrounding area(outer case).
Page 92
>a__WcU[S^ <[c >a`V[e[a`Wc For three phase (380-400V, 3N~, 50Hz),outdoor unit. Fig. 20 1 2 3 INDOOR UNIT TERMINAL BLOCK OUTDOOR UNIT R S T N 1 2 3 TERMINAL BLOCK POWER SUPPLY: 380-400V, 3N~,50Hz For single phase (1PH, 220-230V~, 50Hz),outdoor unit. 1 2 3 INDOOR UNIT TERMINAL BLOCK...
Page 96
>a__WcU[S^ <[c >a`V[e[a`Wc Pipe material and size Phosphorus deoxidized copper seamless Type Pipe material pipe (TP 2M ) for air conditioner 12.70 Gas side Pipe size For series 182 (mm) Liquid side 6.35 Gas side 15.88 Pipe size For series 242 (mm) Liquid side 9.52...
Page 97
>a__WcU[S^ <[c >a`V[e[a`Wc The notch upward(Attached detail view) Field piping side Indoor unit Subsidiary insulation tube Electric wiring WARNING DANGER OF BODILY INJURY OR DEATH TURN OFF ELECTRIC POWER AT CIRCUIT BREAKER OR POWER SOURCE BEFORE MAKING ANY ELECTRIC CONNECTIONS. GROUND CONNECTIONS MUST BE COMPLETED BEFORE MAKING LINE VOLTAGE CONNECTIONS.
Page 98
>a__WcU[S^ <[c >a`V[e[a`Wc 6.5 Med ESP duct indoor unit (AD18-AD48) Safety precautions of indoor unit Please read these "Safety Precautions" firstly when performing the installation work. Though the precautionary points indicated herein are divided under two headings, those points which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in the section.
Page 99
>a__WcU[S^ <[c >a`V[e[a`Wc NOTICE All Wiring of this installation must comply with NATIONAL, STATE AND LOCAL REGULATIONS. These instructions do not cover all variations for every kind of installation circumstance. Should further WARNING BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. FAI-LURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE SERIOUS INJURY OR DEATH, EQUIPMENT (1) Preparation of indoor...
Page 100
>a__WcU[S^ <[c >a`V[e[a`Wc Dimensions 1406 1600 1660 (b) Hanger bolts installation Use care of the piping direction when the unit is installed. Insert Hole-in anchor Hole-in plug Concrete Hanging bolt M10 Hanging bolt M10 nut M10 washer (5) Installation of indoor unit Fix the indoor unit to the hanger bolts.
Page 101
>a__WcU[S^ <[c >a`V[e[a`Wc When connecting the drain pipe to unit, pay suffcient attention Stage not to apply excess force to the piping on the unit side. Also, fix difference Drain hose part Drain socket the piping at a point as close as possible to the unit. Drain socket VP 25 joint Pipe cover(large)
Page 102
>a__WcU[S^ <[c >a`V[e[a`Wc (7) Installation work for air outlet ducts Air conditioner main unit Heat inlet duct insulation (optional or Suction panel Ceiling surface marketat item) (Silent panel) A Blowout duct B Special blowout special inlet (option) (Optional or marketed item) (Option) (with air filter) Hole for check...
Page 103
>a__WcU[S^ <[c >a`V[e[a`Wc Select wire sizes and circuit protection from table below. (This table shows 20 m length wires with less than 2% voltage drop.) Power Circuit breaker Earth leakage breaker Item source wire Switch breaker Switch Leak Overcurrent Phase size Model protector...
Page 104
>a__WcU[S^ <[c >a`V[e[a`Wc 6.6 High ESP duct indoor unit (AD28-AD60) 1. Before installation [Before finishing installation, do not throw the attached parts installation needs] Confirm the way to move the unit to the installation place. Before moving the unit to the installation place, do not remove their packages. When have to remove the package, use a soft material or protection board with rope to lift the unit assembly to avoid unit damage or bumping a scrape.
Page 105
>a__WcU[S^ <[c >a`V[e[a`Wc (2) If necessary, cut the opening installation and checking needed on the ceiling. (If has ceiling) Before installation, finish the preparation work of all the pipes (refrigerant, drainage) and wire (wire controller connection wire, indoor and outdoor unit connection wire) of indoor unit, so that after installation, they can be immediately connected with outdoor unit.
Page 106
Air suction grille with air filter Checking meatus Please consult the after-sales service worker of Haier Air Conditioner for the choosing and installation of suction inlet, suction duct, discharging outlet and discharging duct. Calculating the design drawing and outer static pressure, and choose the discharging duct with proper length and shape.
Page 107
>a__WcU[S^ <[c >a`V[e[a`Wc 7. Calculation method of the dimension of the simple quadrate air duct Presuming the unit length friction impedance of the duct is 1Pa/m, when the dimension of one side of the air duct is fixed as 250mm, as shown below: AD362AHEAA AD482AHEAA AD282AHEAA...
Page 108
>a__WcU[S^ <[c >a`V[e[a`Wc Air discharging fan Improper example 10. The operation method of fan controller Through the fan controller switch in the electric box, the air volume of this unit can be continuously adjusted. It is unnecessary to adjust air volume through the duct side wind level (unit outside static adjustment). The air volume set should be in the operation air volume range.
Page 109
>a__WcU[S^ <[c >a`V[e[a`Wc When connect the pipe to the unit or dismantling the pipe from the unit, please follow the figure shown, use spanner and torque spanner together. When connect cone nut, the inner side and outside of cone nut should paste with refrigerant oil. Use hand to twist 3-4 rings, then fasten with spanner.
Page 110
>a__WcU[S^ <[c >a`V[e[a`Wc Power source Circuit breaker Earth leakage breaker Item wire size Switch Leak Switch breaker Overcurrent Phase (minimum) Model breaker(A) current(mA) protector AD282AHEAA AD362AHEAA AD482AHEAA AD602AHEAA AD282AHEAA AD362AHEAA (2) Wiring connection Make wiring to supply power to the outdoor unit, so that the power for the indoor unit is supplied by terminals.
Page 114
>a__WcU[S^ <[c >a`V[e[a`Wc 6.8 Wall mounted indoor unit (AS182AVERA) INSTRUCTIONS TO INSTALLATION Please read these "Safety Precautions" first then accurately execute the installation work. The precautionary points indicated herein are divided under two headings: WARNING and CAUTION those points which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in the WARNING section.
Page 115
>a__WcU[S^ <[c >a`V[e[a`Wc INSTRUCTIONS TO INSTALLATION PRECAUTION Execute proper grounding. Do not connect the earth wire to a gas pipe, water pipe, lightening rod, or a telephone ground wire. Improper placement of earth wires can result in electric shock. An electric leakage breaker must be installed, otherwise electric shock or other accidents would occur.
Page 116
>a__WcU[S^ <[c >a`V[e[a`Wc INSTRUCTIONS TO INSTALLATION WARNING BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE SERIOUS INJURY OR DEATH, EQUIPMENT MALFUNCTION AND/OR PROPERTY DAMAGE. BE SURE TO READ INSTALLATION MANUAL FOR INDOOR UNIT WITH THIS MANUAL. 1.Accessories Confirm accessories shown below are attached in the bag with this Installation manual.
Page 117
>a__WcU[S^ <[c >a`V[e[a`Wc INSTALLATION PROCEDURE When the mounting plate is first fixed 1. Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be fixed against the wall, then temporarily fasten the plate with one steel nail. 2.
Page 118
>a__WcU[S^ <[c >a`V[e[a`Wc INSTALLATION PROCEDURE Other direction piping Cut away, with a nipper, the lid for piping according to the piping direction and then bend the pipe according to the position of wall hole. When bending, be careful not to crash pipes. Connect beforehand the indoor/outdoor electric cable, and then pull out the connected to the heat insulation of connecting part specially.
Page 119
>a__WcU[S^ <[c >a`V[e[a`Wc Fig. 18 Screw with special washer Screw with Insulation tube special washer Round Cord clamp terminal Round Terminal terminal board Wire Wire Use VW-1, 0.5 to 1.0 mm thick, PVC tube as the insulation tube. INSTALLATION CHECK AND TRIAL OPERATION Check the Layout of the Drain Pipe and Connection Wires The drain pipe should be placed underneath, and the connection wires should be placed upside;...
Page 120
>a__WcU[S^ <[c >a`V[e[a`Wc 6.9 Outdoor unit (AU18-AU60) Carefully read the following information in order to operate the airconditioner correctly. Below are listed three kinds of Safety Cautions and Suggestions. Incorrect operations may result in severe consequences of death or serious injuries. WARNING! CAUTION! Incorrect operations may result in injuries or machine damages;...
Page 121
>a__WcU[S^ <[c >a`V[e[a`Wc WARNING! No goods or nobody is permitted to Installed electrical-leaking circuit placed on or stand on outdoor unit. breaker. It easily cause electrical shock without The falling of goods and people may circuit breaker. cause accidents. Air-conditioner can't be installed in the environment with inflammable gases because the inflammable gases near to air-conditioner may cause fire...
Page 122
>a__WcU[S^ <[c >a`V[e[a`Wc 1. Accessories Edging "Edging" for protection of electric wires from an opening edge. 2. Selection of the place of installation Select the place of installation satisfying the following conditions and, at the same time, obtain a consent from the client or user. Place where air circulates.
Page 125
>a__WcU[S^ <[c >a`V[e[a`Wc Precautions for refrigerant piping Do not twist or crush piping. Be sure that no dust is mixed in piping. Bend piping with as wide angle as possible. Keep insulating both gas and liquid piping. Check flare-connected area for gas leakage. Piping connection Connecting method (indoor unit) Apply refrigerant oil at half union as large and flare nut.
Page 126
>a__WcU[S^ <[c >a`V[e[a`Wc Check if the pressure drops If the pressure does not drop, the unit is passed If the pressure drops, please check the leaking point. After pressurizing for 24 hours, each 1 C difference of ambient temperature will result in 0.01MPa(0.1kg/cm g) pressure change.
Page 127
>a__WcU[S^ <[c >a`V[e[a`Wc Charging amount of refrigerant When the total length (L) of the two indoor units' connecting pipe is less than 5m, it is unnecessary to charge additional refrigerant. If the connecting pipe (L) exceeds 5m, it shall charge Mg additional refrigerant per meter. That is: Refrigerant charging amount = (L-5) x M (g) For the unit with liquid pipe 6.35mm, M=30 For the unit with liquid pipe 9.52mm, M=...
Page 128
>a__WcU[S^ <[c >a`V[e[a`Wc For: AU182AEEAA To Indoor Unit 1 2 3 OUTDOOR UNIT TERMINAL BLOCK For: AU242AGEAA, AU282AHEAA, AU182AFERA, AU242AGERA To Indoor Unit 1 2 3 OUTDOOR UNIT TERMINAL BLOCK 1PH, 220-230V~, 50Hz POWERSUPPLY: For: AU28NAHEAA, AU36NAIEAA, AU48NAIEAA, AU60NAIEAA To Indoor Unit OUTDOOR UNIT R S T N 1 2 3...
Page 129
>a__WcU[S^ <[c >a`V[e[a`Wc 7 Electric control functions 7.1 Fixed frequency unit 7.1.1 Control Features The brief introduction includes those for each item of various types of air conditioners and The brief introduction includes those for each item of various types of air conditioners and their electric control functions.
Page 130
>a__WcU[S^ <[c >a`V[e[a`Wc (2) Auto Selection of Wind Speed In the following, Tr means room temperature while Ts means setting temperature. a. During cooling program conversion of wind speed from the low to high won’t work until the present speed has continued for 3 minutes while conversion from the high to low needs no time delay.
Page 131
>a__WcU[S^ <[c >a`V[e[a`Wc blowing fan runs at setting wind speed. This working area is defined as area A. (2) Ts Tr Ts + 2 , the compressor and outdoor blowing fan run for 10 minutes then pause for 6 minutes, while indoor blowing fan runs at low wind speed. This working area is defined as area B.
Page 132
>a__WcU[S^ <[c >a`V[e[a`Wc setting wind speed. (6) Afterheat blowing during heating program During heating program, the compressor will stop running (except overheat protection or frost removal) while the indoor blowing fan will firstly run for 50 seconds at low speed then stop.
Page 133
(12) Monitoring of remote network Through preset interface, the air conditioner is connected to remote control detector (made by Haier) with 2-core cables for wire communication, to execute instructions sent from computer or centralized controller via remote control detector and meanwhile send present running status and trouble information of the machine to remote control detector.
Page 134
>a__WcU[S^ <[c >a`V[e[a`Wc 7.1.2 Defrost operation flow chart Come to defrost Compressor Open outdoor fun Compressor Condition off or 55s? E-Heat off for 30s? compress Return Operation indoor fun motor Return 4-way value Turn off compressor Return outdoor fun compressor Compressor ON ? Turn off for...
Page 135
>a__WcU[S^ <[c >a`V[e[a`Wc 7.2 Inverter unit 7.2.1 Outdoor running frequency and the control procedure 7.2.1.1 Compressor startup Compressor running frquency range: Outdoor temp. Heat 20RPS 92RPS 20RPS 83RPS Cool 20RPS 85RPM 20RPS 85RPS Defrost 85rpm Every time compressor is from OFF to ON, no matter how is the indoor target frequency, compressor running frequency must be stay at 40Hz and 60Hz for 1 minutes (At outdoor discharging temp.
Page 136
>a__WcU[S^ <[c >a`V[e[a`Wc frequency: Compressor F<25Hz 25Hz F<45Hz 45 F frequency in cooling Over 28 Class-3 Class-5 Class-7 Below 28 Class-1 Class-3 Class-5 Compressor frequency F<25Hz 25Hz F<45Hz 45 F in heating Over 15 Class-2 Class-4 Class-5 Below 15 Class-3 Class-5 Class-7 7.2.2.4 Outdoor fan speed control when selecting AC motor...
Page 137
>a__WcU[S^ <[c >a`V[e[a`Wc 5 6 7 pulse 7.2.3.2 Retentive open angle in 2 minutes after compressor starts up: Cool, dry Outdoor temp. 22 ~ Compressor frquency 30~60 30~60 PMV open angle Heat Outdoor temp. Compressor frquency 30~60 30~60 PMV open angle 7.2.3.3 Standard open angle in 2 minutes after compressor starts up: Cool, dry Outdoor temp.
Page 138
>a__WcU[S^ <[c >a`V[e[a`Wc TD 55 , +1 degree / 2 minutes, and plus to 0 degree gradually Heating Td 35 +1 degree / 2 minutes Max. +5 Td 40 , keep the angle TD 40 , -1 degree / 2 minutes, and reduce to 0 degree gradually 7.2.4 4-way valve control The 4-way valve control in defrosting: refer to the defrosting procedure.
Page 139
>a__WcU[S^ <[c >a`V[e[a`Wc (3): Defrost operation for 9 minutes contineously. E. If the quit condition can be met, the unit will perform: Compressor stops, and outdoor motor runs. 50 seconds later the 4-way valve is close, then 60 seconds later, compressor will perform as startup procedure. F.
Page 140
>a__WcU[S^ <[c >a`V[e[a`Wc overhigh protection. If it is below 48 , the unit will resume to be normal. reduce slowly remaining rise slowly P: reduce at the speed of 1Hz/10s Q: remain the previous value R: rise at the speed of 1Hz/10s 7.2.9.4 Overcurrent protection(realised by power module) In the course of compressor startup, if current is over 13A and keeps for 3 seconds, compressor will stop and the unit alarms.
Page 141
>a__WcU[S^ <[c >a`V[e[a`Wc When receiving the indoor rated operation command, the unit will enter rated cooling operation. Rated heating: When receiving the indoor rated operation command, the unit will enter rated cooling operation. When receiving the indoor min. heating operation command, the unit will enter min. heating operation.
Page 142
>a__WcU[S^ <[c >a`V[e[a`Wc Ensure that alarm indicating time is over 2 minutes and 50 seconds. (1): Resumable alarm, and will be sent to indoor unit. (2): Resumable alarm, but if in 30 minutes it occurs 3 times, it can be resumed only when being electrified after being powered off.
Page 143
>a__WcU[S^ <[c >a`V[e[a`Wc 10111 Module malfunction Module temp. over high 11000 Low pressure switch Low pressure switch acts for 30 seconds failure contineously Temperature cutoff protection 1 Indoor pipe temp. is abnormal, outdoor default cooling temp. : 5 , heating temp.: 40 . The above temperatures are normal.
Page 144
>a__WcU[S^ <[c >a`V[e[a`Wc 8 Electrical wiring diagram and PCB photo 8.1 Inverter outdoor unit AU182AFERA, AU242AGERA T3.15A - 250VAC Note: the PCB code for AU182AFERA and AU242AGERA is 0010452040. -142-...
Page 145
>a__WcU[S^ <[c >a`V[e[a`Wc Outdoor main control board 0010452040 CN27 CN26 CN25 CN19 CN10 CN11 CN12 CN13 CN14 CN21 CN16 CN15 CN17 Outdoor filter board 0010403645 Outdoor indicator board 010452047 CN25 LED1 LED2 LED3 LED4 SW05 LED5 SW05 is used for factory quality control engineers, the default position is: OFF OFF OFF ON for AU182AFERA, as for AU242AGERA, the default position is: OFF OFF OFF OFF, for the above models, there are also module board 0010403555.
Page 146
>a__WcU[S^ <[c >a`V[e[a`Wc AU362AHERA 0150500546 CIRCUIT DIAGRAM OF OUTDOOR UNIT CRANKCASE 4-WAY CAPACITOR AC FAN 2 MOTOR HEATER VALVE AC FAN 1 MOTOR REACTOR capacitor capacitor CN20 L M H CN19 CN23 CN22 CN17 CN18 T/RB CN21 SPDU FUSE1 TO ISPM ISPM 250VAC T5A CN14...
Page 147
>a__WcU[S^ <[c >a`V[e[a`Wc 8.2 Fixed frequency outdoor unit AU182AEEAA 0010573313 CIRCUIT DIAGRAM OF OUTDOOR UNIT RELAY TRANS. FAN MOTOR SPEED CONTROLLER FAN MOTOR CAP. CIRCUIT HIGH PRESSURE SWITCH FAN MOTOR DETECTOR 4-WAY VAVLE WIND CN10 CRANK LOW PRESSURE SWITCH HEATER OUTDOOR AMBINENT SENSOR CN12 OUTDOOR PIPING SENSOR...
Page 148
>a__WcU[S^ <[c >a`V[e[a`Wc AU242AGEAA CIRCUIT DIAGRAM OF OUTDOOR UNIT TRANS. RELAY 3 HIGH PRESSURE SWITCH FAN MOTOR LOW PRESSURE SWITCH SPEED CN10 CONTROLLER MOTOR OUTDOOR AMBINENT SENSOR CAP. CN12 FAN MOTOR OUTDOOR PIPING SENSOR CN11 4-WAY VAVLE DISCHARGE SENSOR SOLENOID FUSE T3.15A/250VAC COMPRESSOR...
Page 149
>a__WcU[S^ <[c >a`V[e[a`Wc AU362AIEAA CIRCUIT DIAGRAM OF OUTDOOR UNIT TRANS. RELAY 3 HIGH PRESSURE SWITCH FAN MOTOR LOW PRESSURE SWITCH SPEED CN10 CONTROLLER MOTOR OUTDOOR AMBINENT SENSOR CAP. CN12 FAN MOTOR OUTDOOR PIPING SENSOR CN11 4-WAY VAVLE MOTOR DISCHARGE SENSOR SOLENOID FUSE MOTOR...
Page 150
>a__WcU[S^ <[c >a`V[e[a`Wc AU28NAHEAA, AU36NAIEAA, AU48NAIEAA, AU60NAIEAA 0010573510 CIRCUIT DIAGRAM OF OUTDOOR UNIT TRANS. HIGH PRESSURE SWITCH MOTOR FAN MOTOR MOTOR SPEED CN10 CONTROLLER LOW PRESSURE SWITCH MOTOR OUTDOOR AMBINENT SENSOR CN12 FAN MOTOR 4-WAY VALVE OUTDOOR PIPING SENSOR SOLENOID CN11 COMPRESSOR VENT SENSOR MAGNETIC CONTACTOR...
Page 157
>a__WcU[S^ <[c >a`V[e[a`Wc Fan speed control board 001A3300352E Fan speed adjusting board test method Place Port F voltage output VAC Connect the test device with fan speed adjusting 132-139 board, dial power switch ON, then revolve P1 slowly to 151-158 place 1, place 2, place 3…...
Page 160
>a__WcU[S^ <[c >a`V[e[a`Wc Condition for the PCB data: 1.Working ambient temperature: 10 70 , relative humidity:30% 95% 2.Preserved ambient temperature: 20 relative humidity 30% 95% 3.Power supply:220VAC 50/60Hz voltage range:160V 250V 4.Precise of temperature control: 1 0010451167E PCB information – port and definition connect to external power supply, live line: L (220VAC) connect to external power supply, neutral line: N (0VAC) P3 4 5 6...
Page 161
>a__WcU[S^ <[c >a`V[e[a`Wc CN15 input signal, detecting water level of float switch 1-3 short circuit is normal, cut off shows that level exceeds the limitation .If float switch cuts off or occurs other failure, LED1 will flash 10 times. CN16 input control, wiring port of central controller: REMOTE 1 RS485-B 2 RS485-A CN17 output signal, output signal of failure alarm, control external load, 12V/ALM 1.
Page 162
>a__WcU[S^ <[c >a`V[e[a`Wc indoor unit. Door card control: controls ON/OFF, the start up setting will comply with last time request memorized according to condition memorize function. Its difference with emergency switch of convertible type unit lies: the emergency switch control will perform in the condition: 24degrees, auto fan speed in auto mode. The function combination between door card and remote/wired control type: select by dip switch: SW2-4 0 means “and”, 1 means later coming is preferential.
Page 163
>a__WcU[S^ <[c >a`V[e[a`Wc AP422ACEAA CIRCUIT DARGRMA OF INDOOR UNIT TRANS. ROOM TEMP. T6.3A/250VAC FUSE PIPING TEMP. TERMINAL BLOCK TO OUTDOOR UNIT REMOTE SWING FAN MOTOR CAP. MOTOR FAN MOTOR 0010451432 CN19 CN16 CN17 CN10 CN14 CN15 CN26 CN25 CN24 CN23 CN22 CN21 LED1...
Page 164
>a__WcU[S^ <[c >a`V[e[a`Wc AP482AKEAA CIRCUIT DIAGRAM OF INDOOR UNIT 0010578100 TRANSFORMER CN24 T3.15A/250VAC ROOM TEMP. SENSOR CN25 FUSE PIPING TEMP. SENSOR CONTROL PANEL CN23 CN22 CN11 CN12 CN13 CN10 ONE-OFF FUSE SWING MOTOR SWING MOTOR RESUMABLE PROTECTOR HEATER REMOTE CONTROLLER CAPACITOR FAN MOTOR B:BLACK...
Page 166
>a__WcU[S^ <[c >a`V[e[a`Wc AS182AVERA WIRING DIAGRAM OF WALL MOUNTED UNIT 0010576611 SWING SWING SWING SWING MOTOR 2 MOTOR 3 MOTOR 4 MOTOR 1 RECEIVER PIPING TEMP. SENSOR NEGATIVE ION GENERATOR CON3 R-MOTOR L-MOTOR UP DOWN ROOM TEMP. SENSOR FUSE T3.15A/250VAC CENTRALIZED CONTROLLER CON1...
Page 167
>a__WcU[S^ <[c >a`V[e[a`Wc 8.4 sensor characteristic model name code sub-part code characteristic outdoor ambient temperature R25=10K ±3% 0010450192 001A3800082 sensor B25/50=3700K±3% R25=10K ±3% mid-condenser temperature sensor 0010450195 001A3800093 B25/50=3700K±3% AU242AGERA R25=10K ±3% oil temperature sensor 0010451305 001A3800093 B25/50=3700K±3% R80=50K ±3% discharging temperature sensor 0010451313 001A3800096...
Page 172
>a__WcU[S^ <[c >a`V[e[a`Wc Failure code for wall mounted unit(AS182AVERA) ---- displayed on the indoor LCD: Failure description Remark code Indoor room temperature sensor failure Indoor room temp. sensor in short circuit, or open circuit, it can resume due to the signal. Indoor coil temperature sensor failure Indoor coil temp.
Page 173
>a__WcU[S^ <[c >a`V[e[a`Wc Failure code for AP422ACEAA Central Number Panel -ized Fault description Possible cause Remedy display control flashes readout Fault in indoor ambient Sensor open-circuit Restorable when given temperature sensor short-circuit for 2min or longer. corrective signal. Fault indoor coil Sensor open-circuit...
Page 174
>a__WcU[S^ <[c >a`V[e[a`Wc 9.2 Troubleshooting for inverter units Outdoor troubleshooting: B elow the indication on indicator board sequence is LE D 5-LE D 4-LE D 3-LE D 2-LE D 1, 0: O FF; 1: O N 1 ) S ensor failure A larm condition: am bient tem perature sen sor is in short circuit or open circuit for 3 seconds con tinously.
Page 175
>a__WcU[S^ <[c >a`V[e[a`Wc 3) Outdoor DC motor abnormal Outdoor indicator displays 00010. Alarm condition:outdoor DC motor is blocked rotor or broken, abnormal. This fault is only used when indoor unit is with DC fan motor. outdoor indicator shows 00010 adjust fan blade to Check if the outdoor unit fan make it run normally blade is blocked by some objects...
Page 176
>a__WcU[S^ <[c >a`V[e[a`Wc For convertible unit and ceiling concealed unit: compressor can not startup after unit is switched on for 4 minutes if indoor unit alarms other eliminate other failure codes faults check if wiring between indoor adjust wiring and and outdoor is correct, power power supply supply is 50Hz...
Page 177
>a__WcU[S^ <[c >a`V[e[a`Wc 6) Outdoor SPDU module over current protection Outdoor indicator shows 00101. Alarm condition: When compressor running, the module current is over 21A. outdoor failure indicator shows 00101 check if the refrigerant is adjust refrigerant too much or too less check if the piping is adjust piping blocked...
Page 178
>a__WcU[S^ <[c >a`V[e[a`Wc 9) EEPROM is abnormal Outdoor indicator shows 01110. Alarm condition: EEPROM is fault or data is missing. outdoor indicator shows 01110 check if EEPROM welded points adjust EEPROM on outdoor PCB is in good welded point condition EEPROM data is missing, replace PCB 10) Running state detecting abnormal...
Page 179
>a__WcU[S^ <[c >a`V[e[a`Wc 12) Outdoor low pressure abnormal Outdoor indicator shows 11000. Alarm condition: outdoor system pressure is lower than 0.05MPa. outdoor indicator shows 11000 measure actual pressure by a replace pressure pressure gauge to adjust the switch output failure low pressure abnormal check if high...
Page 180
>a__WcU[S^ <[c >a`V[e[a`Wc 2) EEPROM failure Alarm condition: before being electrified, EEPROM is faulty or the data is missing. outdoor failure indicator shows 01110 check the EEPROM modify the welded point on outdoor welded point PCB is normal EEPROM data is missing, replace The indication on indicator board sequence is LED5-LED4-LED3-LED2-LED1, 0: OFF;...
Page 181
>a__WcU[S^ <[c >a`V[e[a`Wc 4) Indoor DC motor abnormal Alarm condition:outdoor DC motor is blocked rotor or broken, abnormal. This fault is only used when indoor unit is with DC fan motor. LCD of wall mounted unit display F2 adjust fan blade to Check if the indoor unit fan blade make it run normally is blocked by some objects...
Page 182
>a__WcU[S^ <[c >a`V[e[a`Wc 9.3 Troubleshooting for fixed frequency units 1) Pressure protection Confirm the fault according to the fault code list Does system have Are CN17 and CN18 Replace PCB pressure switch? in PCB cut off? Make them in short circuit Is actual pressure detected by Change pressure pressure gage acceptable?
Page 183
>a__WcU[S^ <[c >a`V[e[a`Wc 3) Low pressure protection - Wired controller shows Confirm the fault according to the fault code list Are connectors of pressure switch in good Check and reconnect condition? Is low side pressure switch Replace PCB activated? (If not, DC voltage is 0V.) Is the low side pressure detected by the gage lower than threshold value? Replace low pressure...
Page 184
>a__WcU[S^ <[c >a`V[e[a`Wc 4) High pressure protection - Wired controller shows Confirm the fault according to the fault code list Are connectors of pressure switch in good Check and reconnect condition? Is high side pressure switch Replace PCB activated? (If not, DC voltage is 0V.) Is the high side pressure detected by Replace high pressure the gage higher than threshold...
Page 185
>a__WcU[S^ <[c >a`V[e[a`Wc >a__WcU[S^ <[c >a`V[e[a`Wc 5) Communication error between indoor and outdoor units - Wired controller shows Confirm commumication failure according to the fault code list Confirm the fault indicator is communication failure Are communication wire Does indoor communication S and supply wires L and re-wiring indicator flash?
Page 186
>a__WcU[S^ <[c >a`V[e[a`Wc 7) High current protection in 3-phase fixed frequency models - Wired controller shows Is three-phase circuit not balanced? Is supply voltage too Modify power supply circuit low? Is supply voltage too low at compressor start-up? Is power cable or compressor wire re-wiring securely connected? Properly? Confirm detecting circuit...
Page 187
>a__WcU[S^ <[c >a`V[e[a`Wc 9) Overcurrent protection for single-phase fixed frequency models- Wired controller shows Is supply voltage too low? Especially modify power supply circuit when compressor starts up? Is supply wire securely re-wiring connected? Is compressor current more than overcurrent Confirm detecting circuit protection limit? Is current detecting circuit in is abnormal,replace...
Page 188
>a__WcU[S^ <[c >a`V[e[a`Wc 10) Temperature cutoff protection- Wired controller shows confirm the malfunction according to the fault code list Does small relay coil Is outdoor four-way valve Relay is broken. of four-way valve have in good condition during Replace PCB a voltage of 12V DC? heating cycle? Does four-way...
Page 189
>a__WcU[S^ <[c >a`V[e[a`Wc 11) Fault in drain system- Wired controller shows confirm the malfunction according to the fault code list Unclog pipe and Is drain pipe clogged? water pump Is pump motor in Replace water good condition? pump Is drain pan dirty and Clean drain pan float switch ineffective? Is float switch holder tinted...
Page 190
>a__WcU[S^ <[c >a`V[e[a`Wc 13) Troubleshooting (before replacement of PCB) Service call For example: no cooling, etc. Fault confirmation 1.Is supply voltage acceptable? Confirm operating 2.Is temperature setting correct? (e.g. too high) conditions 3.Is system in TIMER mode? 4.Is user aware of product features, etc. Is the feature not Explain product available for present...
Page 221
>a__WcU[S^ <[c >a`V[e[a`Wc 13. Air velocity distribution 18000BTU/h indoor uni 1) Cassette type (AB182*****) a. Cooling / Air Velocity Distribution Cooling Blowy angle:40 Air Velocity Distribution b. Cooling / Temperature Distribution Cooling Blowy angle:40 Temperature Distribution c. Heating / Air Velocity Distribution Heating Blowy angle:70 Air velocity Distribution...
Page 222
>a__WcU[S^ <[c >a`V[e[a`Wc 2)Convertible type (AC182*****) a) Grounding a. Cooling / Air Velocity Distribution Cooling Blowy angle:25 0.5m/s Air Velocity Distribution 1.0m/s 1.5m/s b. Cooling / Temperature Distribution Cooling Blowy angle:25 Temperature Distribution c. Heating / Air Velocity Distribution Heating Blowy angle:5 Air velocity Distribution d.
Page 223
>a__WcU[S^ <[c >a`V[e[a`Wc b) Ceiling a. Cooling / Air Velocity Distribution Cooling Blowy angle:25 Air Velocity Distribution b. Cooling / Temperature Distribution Cooling Blowy angle:25 Temperature Distribution c. Heating / Air Velocity Distribution Heating Blowy angle:65 Air velocity Distribution d. Heating / Temperature Distribution Heating Blowy angle:65 Temperature Distribution...
Page 224
>a__WcU[S^ <[c >a`V[e[a`Wc 3)Duct type (AD182*****) cooling air discharge angle Air Velocity distribution cooling air discharge angle 5 Temperature distribution heating air discharge angle 45 Air Velocity distribution heating air discharge angle 45 Temperature distribution -222-...
Page 225
>a__WcU[S^ <[c >a`V[e[a`Wc 24000~28000BTU/h indoor units Model: AC282***** a. Cooling / Air Velocity Distribution Cooling Blowy angle:25 0.5m/s Air Velocity Distribution 1.0m/s 1.5m/s b. Cooling / Temperature Distribution Cooling Blowy angle:25 Temperature Distribution Model: AB282***** a. Cooling / Air Velocity Distribution Cooling Blowy angle:40 Air Velocity Distribution...
Page 226
>a__WcU[S^ <[c >a`V[e[a`Wc AD282***** cooling air discharge angle 5 Air Velocity distribution cooling air discharge angle 5 Temperature distribution -224-...
Page 227
>a__WcU[S^ <[c >a`V[e[a`Wc 36000~42000BTU/h indoor units 1)AB362***** a. Cooling / Air Velocity Distribution Cooling Blowy angle:40 Air Velocity Distribution b. Cooling / Temperature Distribution Cooling Blowy angle:40 Temperature Distribution 2) AC362***** a. Cooling / Air Velocity Distribution Cooling Blowy angle:25 Air Velocity Distribution b.
Page 243
>a__WcU[S^ <[c >a`V[e[a`Wc [FAN] [HIGH] high fan speed [FAN] [MED] medium fan speed [FAN] [LOW] low fan speed [FAN] [FIX] fixed fan speed, it will display only when fixed fan speed is requested to main indoor unit. [CENTRAL] central control mode [OPERATION] running mode [STAND BY]...
Page 244
>a__WcU[S^ <[c >a`V[e[a`Wc AUTO operation, COOLING, HEATING and DEHUMIDIFICATION operation 1) Start up operation: press the button of ON/OFF, the system will start up, and will display [MODE][AUTO] [FAN][AUTO] [ROOM TEMP.]+ 24 [CLOCK]+”12 00”. 2) Select MODE: press the MODE button, then you will see in the display section [MODE] switch over in below sequence:[FAN ONLY] [COOL] [DRY]...
Page 245
>a__WcU[S^ <[c >a`V[e[a`Wc TIMER ON, press [TIMER]. [TIMER][ON] will be constant on. Then [TIMER] [OFF] flashes, press the clock +/- button to adjust the time of TIMER OFF, press [SET]. The time sequence of timer on and timer off will determine the mode is [TIMER] [ON] [OFF] or [TIMER] [OFF] [ON].
Page 246
>a__WcU[S^ <[c >a`V[e[a`Wc CENTRAL control function When the central controller selects [CENTRAL] mode, the buttons in the wired controller except for [CHECK] will be invalid. VENTILATION mode (only for the unit with fresh air function or heat recovery function) Press [RECOVERY] button, then the unit will switch over the ventilation mode: [VENTILATION][AUTO] [VENTILATION][RECOVERY] [VENTALATION][NORMAL]...
Page 247
>a__WcU[S^ <[c >a`V[e[a`Wc Preset Outdoor total capacity Actual value, decimal In check mode, press [CHECK] to quit the check mode, and go into normal running mode. How to change the function switches? Type State of Function description switch Changeover Wired Connected Central controller controller...
Page 248
>a__WcU[S^ <[c >a`V[e[a`Wc There is no lock function only in the wired controller. But when it is connected with a central controller, if the central controller is set to “central”, the buttons in the wired controller will be invalid, or the buttons will be valid. Setting address method: The address setting can be realized by setting indoor PCB.
Page 252
>a__WcU[S^ <[c >a`V[e[a`Wc Electrical functions of wired controller: 1.Function difference between master wired controller and slave one: Contrastive items Master wired controller Slave wired controller Function All of functions Only with below functions: ON/OFF, MODE, FAN SPEED, SET TEMP., SWING 2.
Page 253
>a__WcU[S^ <[c >a`V[e[a`Wc connected with indoor unit is called master one, the other is called slave one. Master wired controller and indoor unit; master and slave wired controllers are all connected through 3 pieces of polar wire. 3. Communication wiring: The wired controller is equipped with special communication wiring in the accessories.
Page 254
>a__WcU[S^ <[c >a`V[e[a`Wc Weekly timer YCS-A001 PROGRAM NO. Instruction: OFF OFF OFF OFF OFF OFF OFF MON TUE WED THU FRI SAT SUN 1 - PROGRAM-the display shows the weekly Program Holiday Number ON ON ON ON ON ON timer timing setting state, and in setting state, SET 1 ON Hour Cancel...
Page 255
1. Use group controller and weekly timer to realize the group control function + weekly timing function, applicable for the units except for the unit which needs detector to realize the weekly timer function, such as cabinet type, console type. Haier OFF OFF OFF OFF OFF OFF OFF...
Page 256
>a__WcU[S^ <[c >a`V[e[a`Wc PROGRAM NO. Program Holiday Number SET 1 ON Hour Cancel SET 2 ON Min. Confirm Time Week ON/OFF Installation dimensions RS-485 A 12VDC PROGRAM NO. OFF OFF OFF OFF OFF OFF OFF MON TUE WED THU FRI SAT SUN Program Holiday Number...
Page 257
>a__WcU[S^ <[c >a`V[e[a`Wc 4. Central Controller YCZ-A001 Function description: LOCK display Display of operation mode and signal emitting Display of current unit number Location of the indicating cursor Display of fan speed and louver Display of MONI/SET Generally indicating " MONI" . When Total on/ Total off indicator setting ON/OFF or other items, it changes from "...
Page 258
The key for locking key function of the central controller: LOCK. 4. Unit number setting function: To enrich the control functions of Haier commercial air conditioner remote monitoring system, multiple controllers could be set to work together for a combination of multiple functions. For this, the central controller is provided with a two-digital switch for setting controller address.
Page 259
7. Use central controller + weekly timer to realize the group control function + weekly timing function, this type is applicable for the unitary free indoor units except for cabinet type. Haier OFF OFF OFF OFF OFF OFF OFF MON TUE WED THU FRI SAT SUN...
Page 260
>a__WcU[S^ <[c >a`V[e[a`Wc Installation procedure 1. Wire connecting Power supply 1PH , 220-240V~, 50Hz To connect the process control monitor/ detector RS - 485 RS - 232 To connect the computer or MODEM 2. Installation method A wiring box cover must be used. The central controller shall be installed into the installation box built in the wall fastening with 4 screws (as shown).
Page 261
>a__WcU[S^ <[c >a`V[e[a`Wc As illustrated: (Figure 1 is the front view and Figure 2 is the side view) The central controller is 180mm long, 120mm wide and 64.4 mm thick. (Fig.2) 64.4mm...
Need help?
Do you have a question about the CPF12XHLUVB and is the answer not in the manual?
Questions and answers