Table of Contents
Advertisement
Quick Links
432
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, P. O. Box 280
Verdi, NV 89439
Customer Service (775) 345-0444 Ext.502
fax: (775) 345-0569
www.wellsbloomfield.com
OPERATION MANUAL
SELF-LEVELING
DROP-IN
DISPENSERS
for ROUND
DINNERWARE
UT Series
UTS Series
UTH Series
&
UTY Series
Includes
Model UT8
INSTALLATION
Model UTH8
USE & CARE
Model UTS8
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 303848 Rev. (-)
M432 061201 cps
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wells UT Series
Summary of Contents for Wells UT Series
- Page 1 Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
-
Page 2: Limited Warranty Statement
Seller’s obligation under this warranty is limited to the one year from the date of original installation or 18 months repair of defects without charge by a Wells Mfg. Co. factory from the date of shipment from our factory, whichever... -
Page 3: Specifications
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. dispenser. Proper installation, professional operation and consistent maintenance of this dispenser will ensure that it gives you the very best performance and a long, economical service life. -
Page 4: Features & Operating Controls
FEATURES & OPERATING CONTROLS POWER PLATE GUIDES SWITCH CARRIAGE POWER FLANGE INDICATOR TEMPERATURE CARRIAGE SPRINGS ADJUSTMENT OPEN TUBE SHIELD POWER CORD UT Series UTS Series HEATING UTH Series ELEMENT UTY Series Fig. 1 Features & Operating Controls - Drop-In Round Dinnerware Dispensers... -
Page 5: Precautions And General Information
PRECAUTIONS AND GENERAL INFORMATION WARNING: This dispenser is intended for use in commercial establishments only. Electric Shock hazard This dispenser is intended to dispense dinnerware in establishments serving food for human consumption. No other use is recommended All servicing requiring or authorized by the manufacturer or its agents. -
Page 6: Installation
INSTALLATION NOTE: DO NOT discard UNPACKING & INSPECTION the carton or other packing Carefully remove the dispenser from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from inspected the dispenser for the dispenser before connecting electrical power or otherwise hidden damage and tested it performing any installation procedure. - Page 7 SPRINGS NOTE: Springs for heated and non-heated units are different, and should not be mixed in the same dispenser. Additional springs are available through your Authorized Wells Service Agency. Fig. 2 Carriage Tension 4. Disconnect unused springs from the lower retaining bracket and Adjustment allow them to dangle.
-
Page 8: Operation
OPERATION OPERATING SUGGESTIONS CAUTION: Hot Surface Load the dispenser with the appropriate size dinnerware. Dinnerware which is too large may be broken or may jam the Exposed surfaces of heated carriage. dispensers can be hot to the Dinnerware which is too small cannot be safely dispensed, and may be broken or may jam the carriage. -
Page 9: Cleaning Instructions
CLEANING INSTRUCTIONS CAUTION: PREPARATION Electric Shock Unplug heated units and allow to cool before cleaning. Unload all dinnerware from the dispenser before cleaning. Hazard Use care to avoid removal or deformation of carriage springs. Disconnect dispenser FREQUENCY from electric power Daily before cleaning. -
Page 10: Care Of Stainless Steel
CARE OF STAINLESS STEEL 1. Wells dispensers are constructed of high quality 304 stainless steel. As long as the stainless steel surface is intact, the equipment will not rust or corrode. 2. The surface can be damaged by mechanical abrasion, hard water deposits and chlorine: a. -
Page 11: Parts And Service
503960 service, or to order factory COARSE ADJUSTMENT 503961 CARRIAGE SPRINGS (HEATED UNITS) authorized replacement FINE ADJUSTMENT 503950 parts, contact your Wells COARSE ADJUSTMENT 503966 authorized service agency, or call: Wells Manufacturing Co. 2 Erik Circle P. O. Box 280... - Page 12 WELLS MANUFACTURING COMPANY DIVISION OF CARRIER REFRIGERATION 2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439 Customer Service (775) 345-0444 Ext.502 fax: (775) 345-0569 www.wellsbloomfield.com...
Need help?
Do you have a question about the UT Series and is the answer not in the manual?
Questions and answers