Related Manuals for Planet GSD-804P
Summary of Contents for Planet GSD-804P
- Page 1 8-Port 10/100/1000Mbps with 4-Port PoE Gigabit Ethernet Switch GSD-804P User's Manual...
-
Page 2: Fcc Warning
Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. -
Page 3: Ce Mark Warning
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 8-Port 10/100/1000Mbps with 4-Port PoE Gigabit Ethernet Switch User's Manual For Model: GSD-804P Revision: 1.0 (May 2011) Part No.: 2350-A35100-000... -
Page 4: Table Of Contents
Table of Contents 1. Introduction ....................5 1.1 Checklist ..................... 5 1.2 Product Description ................5 1.3 Features ..................... 5 1.4 Specification..................7 2. Hardware Description .................. 8 2.1 Front Panel ................... 8 2.1.1 LED Indicators ................9 2.2 Rear Panel ................... 9 3. -
Page 5: Introduction
15.4 Watts) and totally 55 Watts PoE budget on half of the 10/100/1000Mbps TP ports of GSD-804P. The four 802.3af PoE ports provide PoE power injector function which is able to drive 4 IEEE 802.3af compliant powered devices. The GSD-804P... - Page 6 Supports PoE Power up to 15.4 Watts for each PoE port Auto detect powered device (PD) Circuit protection prevents power interference between ports Remote power feeding up to 100m Switching Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-X Flow control for Full Duplex operation and back pressure for Half Duplex oper- ation Integrates address look-up engine, supporting 8K absolute MAC addresses 9K Jumbo Frame supports at all speed (10/100/1000Mbps)
-
Page 7: Specification
1.4 Specification Model GSD-804P Hardware Specification Network Connector 8-Port RJ-45 for 10/100/1000Base-T 4-Port with 802.3af PoE injector function, Port-1 to PoE Inject Port Port-4 1 Power, 1 FAN Alert LED LED Display 1-4 port PoE in-use 1-8 port Speed, LNK/ACT... -
Page 8: Hardware Description
804P; term of “switch” can be any third switches. 2.1 Front Panel The Front Panel of the GSD-804P PoE Ethernet Switch consists of 8x Auto-Sensing 10/100/1000Mbps Ethernet RJ-45 Ports. The LED Indicators are also located on the front panel of the GSD-804P. -
Page 9: Led Indicators
2.2 Rear Panel The rear panel of the GSD-804P indicates an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60Hz. And have a fan hole on the rear panel. Figure 2-2: GSD-804P Switch Rear Panel 1. -
Page 10: Hardware Installation
1000Base-T, 100Base-TX and 10Base-T networks. Users only need to plug a working network device into one of the 10/100/1000Base-T ports, and then turn on the GSD-804P. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation with the connected device. -
Page 11: Desktop Installation
3.1 Desktop Installation To install the Switch on desktop, simply follow the next steps: Step 1: Place the Switch on desktop near an AC power source. Step 2: Keep enough ventilation space between the Switch and the surrounding objects. When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 4, in Specification. -
Page 12: Rack Mounting
3.2 Rack Mounting To install the Switch in a 10-inch standard rack, follow the instructions described below. Step 1: Place your Gigabit Ethernet Switch on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. -
Page 13: Product Application
1. Place the GSD-804P on a smooth surface or fasten the mounting brackets purchased separately with the provided screws in a standard 19” rack. 2. Connect the power cord to the power inlet socket of GSD-804P and the other end into the local power source outlet. When the Switch receives power, the Power LED should remain solid Green. -
Page 14: Department/ Workgroup Poe Switch
3.3.2 Department/ Workgroup PoE Switch Providing 4-Port PoE in-line power interface, the GSD-804P can easily build a power centrally-controlled IP phone system, IP Camera system and Wireless AP group for the enterprise. For instance, up to 4 cameras can be installed around the corner in the company for surveillance demands or up to 4 Wireless AP to build a wireless roaming environment in the office. -
Page 15: Power Over Ethernet Powered Device
3.4 Power over Ethernet Powered Device Voice over IP phones Enterprise can install POE VoIP Phone, ATA and other Ethernet/non-Ethernet end-devices to the central where UPS is installed for un-interrupt power system and power control system. 3~5 Watts Wireless LAN Access Points Museum, Sightseeing, Airport, Hotel, Campus, Factory, Warehouse can install the Access Point any where with no hesitation. -
Page 16: Power Over Ethernet Overview
4. Power over Ethernet Overview What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for wired Ethernet, the most widely installed local area network technology adopted today. PoE allows the electrical power necessary for the operation of each end-device to be carried by data cables rather than by separate power cords. - Page 17 Figure 1 - Power Supplied over the Spare Pins The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
- Page 18 When to install PoE? Consider the following scenarios: You’re planning to install the latest VoIP Phone system to minimize cabling building costs when your company moves into new offices next month. The company staff has been clamoring for a wireless access point in the picnic area behind the building so they can work on their laptops through lunch, but the cost of electrical power to the outside is not affordable.
-
Page 19: Troubleshooting
Why I connect my PoE device to GSD-804P and it cannot power on? Solution: 1. Please check the cable type of the connection from GSD-804P(port 1 to port 4) to the other end. The cable should be an 8-wire UTP, Category 5 or above, EIA568 cable within 100 meters. -
Page 20: Appendix A Networking Connection
Appendix A Networking Connection A.1 Data Out PoE Switch RJ-45 Port Pin Assignments (Port 1 to Port-4) PIN NO RJ-45 SIGNAL ASSIGNMENT l Output Transmit Data + l Power + l Output Transmit Data – l Power + l Receive Data + 1 2 3 4 5 6 7 8 l Power - l Receive Data –... -
Page 21: Switch's Rj-45 Pin Assignments - 10/100Mbps, 10/100Base-Tx
A.3 Switch's RJ-45 Pin Assignments - 10/100Mbps, 10/100Base-TX When connecting your Switch to another Fast Ethernet switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/ MDI-X detection. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable. - Page 22 There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Straight Cable SIDE 1 SIDE 2 SIDE 1 1 2 3 4 5 6 7 8 1 = White/Orange 1 = White/Orange 2 = Orange...
-
Page 23: Ec Declaration Of Conformity
*Model Number: GSD-804P * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC). - Page 24 This page is intentionally left blank...