Related Manuals for J&J Electronics Color Splash
Summary of Contents for J&J Electronics Color Splash
- Page 1 Color Splash LED Pool and Spa ® Light Fixture Installation and Operation Guide Technical Support Phone: 800.735.4553 ext. 242 For more information about this or other J&J Electronics lighting products, please visit www.jandjpoolspa.com...
- Page 2 This owner’s manual contains important information on installing and using your new Color Splash LED Pool and Spa light fixture. Read and follow all instructions contained in this manual. Please keep it in a safe place for future reference.
- Page 3 COLOR SPLASH LED POOL AND SPA LIGHT FIXTURES INSTALLATION (NEW POOL AND/OR SPA CONSTRUCTION) The following steps detail installation of the Color Splash LED light fixture into a new pool and/or spa construction. Read this section in its entirety prior to beginning any installation.
- Page 4 WARNING! Confirm that the pool and/or spa meets all current National Electrical Code (N.E.C.) Article 680-22 requirements and any applicable local codes or ordinances. The electrical system must be installed by a licensed or certified electrician to meet or exceed those requirements prior to installation of the light. This includes, but is not limited to, the following National Electrical Code requirements: •...
- Page 5 10 minutes to prevent damage to the light. 5. Using the stainless steel pilot screw provided, install the Color Splash light assembly into the niche, carefully tightening the pilot screw. (Reference Figure 1) WARNING! Use only the stainless steel pilot screw provided with this underwater light.
- Page 6 COLOR SPLASH LED POOL AND SPA LIGHT FIXTURE INSTALLATION (EXISTING POOL AND/OR SPA) Danger - Risk of electrical shock or electrocution! Installation of this light must be completed by a licensed or certified electrician or a qualified pool professional in accordance with the National Electrical Code and any applicable local codes and ordinances.
- Page 7 EXISTING CONSTRUCTION INSTALLATION STEPS (ONCE ALL ELECTRICAL REQUIREMENTS ARE MET) The following steps detail installation of the Color Splash LED light fixture into an existing pool. Read this section in its entirety prior to beginning any installation. WARNING! Pool or spa electrical system must meeting current code requirements.
- Page 8 Figure 1. 10. Install the Color Splash LED light fixture into the niche. 11. Using the stainless steel pilot screw provided, install the Color Splash LED light fixture assembly into the niche, carefully tightening the pilot screw. (Reference Figure 12.
- Page 9 SELECT SOLID COLORS You can select a solid color at anytime by activating the “Color Lock” feature. The Color Lock feature allows you to stop a light show and “lock” Color Splash on a solid color. pg 8...
- Page 10 ACTIVATING THE COLOR LOCK FEATURE Turn the pool light power off and then back again in 2 seconds. Color Splash will “lock” on the color it was displaying at the time when you turned it off. DEACTIVATION THE COLOR LOCK FEATURE Turn the pool light power off and then back on again within 2 seconds.
- Page 11 3. DESERT BLOOM Show: Very slow cross-fade through all seven solid colors. Cycle: Seventy-seven minute color sequence cycle with super slow cross-fade between solid colors. Fixture will stay on each solid color for 10 minutes before moving to the next. 4.
- Page 12 J&J Electronics | Irvine, California www.jandjpoolspa.com © 2013 J&J Electronics, Inc. All rights reserved. Color Splash® is a trademark of and manufactured by J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies. REF. 051513...
Need help?
Do you have a question about the Color Splash and is the answer not in the manual?
Questions and answers
Pool light and spa light don’t match. Now spa light out. Pool light working perfectly.
The J&J Electronics Color Splash pool and spa lights may not match if they are not on the same electrical circuit. The lights are “synchronous,” meaning they will display the same light shows only when connected to the same circuit.
The spa light may not be working due to improper installation, power not being switched “on” at the circuit breaker or light switch, or failure to follow correct wiring procedures. It is also important to ensure the light is submerged in water during operation, as running it dry can cause the light to shut down or become damaged.
This answer is automatically generated