Grizzly G9003 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Planer
  5. G9003
  6. Instruction manual

Grizzly G9003 Instruction Manual

3 3/16" portable planer
Hide thumbs Also See for G9003:
Table of Contents

Advertisement

Quick Links

Download this manual
3
3
⁄
" PORTABLE PLANER
16
MODEL G9003
INSTRUCTION MANUAL
COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
APRIL, 2000 PRINTED IN U.S.A.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G9003 and is the answer not in the manual?

Questions and answers

Related Manuals for Grizzly G9003

Summary of Contents for Grizzly G9003

  • Page 1 INSTRUCTION MANUAL COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. APRIL, 2000 PRINTED IN U.S.A.
  • Page 2 G9003 Portable Planer...

  • Page 3: Safety Instructions For Power Tools

    Keep work area well lighted. G9003 Portable Planer SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
  • Page 4 A guard or other part that is damaged should be properly repaired or replaced. UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. G9003 Portable Planer PARTS.
  • Page 5 ENSURE PLANER IS PROPERLY ADJUSTED BEFORE STARTING. Always use a test piece to check the adjustment and operation before starting on the actual workpiece. G9003 Portable Planer DO NOT REMOVE EXCESSIVE AMOUNTS OF WOOD IN A SINGLE PASS. Better results...

  • Page 6: Control Location

    Setting Jig, Replacement Motor Brushes ON/OFF Trigger Fig 1. Location of controls. ⁄ HP, 110V, 5.0 Amp ⁄ " ⁄ " Included: Fence, Replacement Belt and Trigger Lock Power Cord Rear Foot Belt Cover Fence G9003 Portable Planer ⁄ " Blade...
  • Page 7 Move the straight- edge back and forth across the width of the blade to make sure G9003 Portable Planer the amount of contact is the same all the way across. 3. If there is too much contact, or...

  • Page 8: Blade Installation

    Fig 5. Inserting blade assembly on Blade Assembly so the notches in the side of the Holder engage the rear edge of the blade. Install three hex head bolts and washers, and tighten with the supplied T-handle wrench. blade. G9003 Portable Planer Plate...

  • Page 9: Blade Sharpening

    BLADE SHARPENING The Blade must be completely removed from the Planer and from the Back Plate in order for it to be safely sharpened. Follow the preceding instructions for Blade Removal. For the best results, have planer blades sharpened by a professional sharpening...
  • Page 10 The Planer can be used to cut right down to a scribe line by taking selective cuts. This Planer can also be used for face plan- ing, that is, to clean up the rough surface of a board.
  • Page 11 See Figure 7. Be sure the workpiece is firmly secured with clamps or other holding devices. Start the Planer and let it get to full speed before moving the Cutterhead into the workpiece. Apply steady, even pressure and keep the Planer moving along the edge.

  • Page 12: Maintenance

    Insert the new brush, check to make sure it goes into the slot and comes out against the commutator. 5. Replace the brush cover. 6. Repeat for the other brush. 7. Replace the motor cover. Fig 10. Replacing motor brushes. G9003 Portable Planer...

  • Page 13: Operating Tips

    Always have this device serviced by a qualified electri- cal repair technician. Serious injury will result. G9003 Portable Planer Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment.
  • Page 14 G9003 Portable Planer...
  • Page 15 025 P9003025 Auxiliary Baffle Plate 026 P9003026 Pan Hd Screw M4 x 10 027 P9003027 Bearing Cover 028 P9003028 Carbon Brush G9004 Portable Planer Ref. # Part # Description 029 P9003029 Brush Holder Cap 030 P9003030 Indication Plate 031 P9003031...

  • Page 16: Troubleshooting

    4. Replace belt. 5. Inspect by qualified electrical technician. Replace belt 1. Increase depth of cut. 2. Replace belt. 1. Sharpen blades. 2. Decrease depth of cut. 3. Reverse cutting direc- tion. 4. Dry wood. Reset blades in jig. G9003 Portable Planer...

  • Page 17: Warranty Card

    14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________...
  • Page 18 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
  • Page 19 NOTES G9003 Portable Planer...

  • Page 20: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance.

Table of Contents

Save PDF