USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed. INFLUENCE ALCOHOL. WORKSHOP CHILD UNDER DRUGS Model G5353 Spray Gun...
Page 3
UNINTENTIONAL STARTING. Do not carry tool with hand on trig- ger and always disconnect from air when not in use. Model G5353 Spray Gun 17. DISCONNECT TOOLS before ser- vicing and changing accessories. 18. DO NOT OVERREACH. Keep proper footing/balance at all times.
NOT exceed the recommended inlet air pressure. Excessive pres- sure could cause the spray gun to burst or cause other internal equip- ment damage. 14. LOCAL authorities regarding exhaust and waste disposal requirements. PRESSURE. LAWS. Consult local Model G5353 Spray Gun...
SECTION 2: INTRODUCTION Foreword We are proud to offer the Grizzly Model G5353 Spray Gun. This model is part of a growing Grizzly family of fine tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation, and proof of Grizzly’s commitment to customer...
21-50 PSI Greater Than FLUID PRESSURE CUP MATERIAL Aluminum MAX. PATTERN WIDTH BODY MATERIAL Painted Metal Solids, i.e.. MATERIAL USAGE Enamels & Lacquers WATERBORNE MATERIAL COMPATIBLE G5353 1 liter Siphon 1.6MM 5 CFM 10 PSI 250mm Medium Model G5353 Spray Gun...
Make sure all connections are tight enough to prevent air leaks but not so tight as to damage the tool. 1. Attach the gun body to the cup as shown in Figure 2 . Figure 2. Model G5353 gun body Assembly installation.
Page 8
Trigger: Two stage trigger. Stage one only releases compressed air for blowing off the work piece. Stage two sprays material. Lightly squeeze the trigger for stage one. Squeeze the trigger all the way to spray. Model G5353 Spray Gun Fluid Control...
Model G5353 Spray Gun Spraying The Model G5353 siphon feed spray gun set is designed to spray a wide variety of materials such as lacquers, stains, primers, multi-component paints, clear coats, acrylics, epoxies etc.
Page 10
13. The spray stroke should have even con- sistency and parallel edges. If it doesn't please refer to Troubleshooting on Page 15. CONTAMINATION HAZARD! Dispose of paint waste in a responsible man- ner! Follow manufacturer's recom- mendations and local laws regarding disposal. Model G5353 Spray Gun...
Page 13). Holes Stroke Figure 7. Set up for horizontal stroke direction with vertical fan pattern. Model G5353 Spray Gun Stroke Figure 8. Set up for vertical spray stroke with horizontal fan pattern. Rotating the pattern adjustment control in Figure 8 will give you a range between the two patterns in Figure 9.
H3174—Air Blow Gun with 2 Tips This air blow gun includes a safety tip and rubber tip for all normal air cleaning jobs. ⁄ " NPT . Figure 13. H3174 Air Blow Gun with 2 ⁄ " NPT. pressure regulator. Tips. Model G5353 Spray Gun...
Fluid Tip Needle Cup Lid Figure 14. Disassembly for cleaning. Model G5353 Spray Gun 5. Unscrew the atomizing cap with your fingers and the fluid tip with the ser- vice wrench. The fully disassembled gun should look like Figure 14.
Page 14
B. Air Valve Packing C. Trigger Pin D. Pattern Control E. Fluid Control Knob Allow the lubricant to coat threads, and run into gun body to lubricate all moving parts and seals. Figure 15. General lubrication points. Model G5353 Spray Gun...
1. No pressure at gun. 2. Fluid passages dirty. 3. Fluid control closed. 4. Out of paint. 5. Material too thick. Model G5353 Spray Gun Troubleshooting Solution 1. Tighten fluid tip or replace seat with new one. 2. Add material.
Page 16
1. Lower inlet air pressure. 2. Keep gun at recommended distance. 3. Slow down and maintain consistent even parallel stroke. 1. Clean or replace both. 1. Install an in-line air filter. 2. Replace air line. Model G5353 Spray Gun...
Page 17
GASKET P5353016 HOUSING P5353017 CONTROL BODY P5353018 RING P5353019 COMPRESSION SPRING P5353020 SCREW P5353021 P5353022 PACKING P5353023 VALVE BODY Model G5353 Spray Gun �� �� �� �� �� �� �� � � �� � � �� �� �� �� ��...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 19
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
Page 20
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...