Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly G5354
Summary of Contents for Grizzly G5354
- Page 1 MODEL G5354 AIRBRUSH KIT INSTRUCTION MANUAL COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR9283 PRINTED IN TAIWAN...
-
Page 2: Section 1: Safety
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. - Page 3 Safety Instructions For Pneumatic Tools 17. DISCONNECT TOOLS before ser- 10. USE PROPER AIR HOSE for the vicing and changing accessories. tool. Make sure your air hose is in good condition and is long enough to 18. DO NOT OVERREACH. Keep reach your work without stretching.
- Page 4 Additional Safety Instructions for Spraying READ THIS MANUAL. This manual PROTECTIVE CLOTHING. Protect contains proper operating instruc- exposed skin from overspray by tions for this airbrush. wearing a protective suit or other approved garment. READ MATERIAL LABELS and MATERIAL SAFETY DATA INAPPROPRIATE USE.
-
Page 5: Section 2: Introduction
SECTION 2: INTRODUCTION Foreword Contact Information We are proud to offer the Grizzly Model If you have any comments regarding this G5354 Airbrush. This model is part of a manual, please write to us at the following growing Grizzly family of fine tools. When... -
Page 6: Tool Data Sheet
TOOL DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 Model G5354 Airbrush MODEL G5354 MIX TYPE External TYPE OF FEED Siphon (Bottom) SPRAY PATTERN Pencil Line to 2" TRIGGER ACTION Dual INLET AIR 15-50 PSI... -
Page 7: Section 3: Setup
SECTION 3: SETUP Inventory Assembly Prior to assembly and use of the air- Your airbrush left our warehouse in a care- brush, it is essential that all parts be thor- fully packed box. If you discover the air- oughly cleaned and dried. Please refer to brush is damaged after you have signed for Cleaning in the MAINTENANCE section delivery, please immediately call Customer... - Page 8 Controls 3. Connect the hose from the air com- pressor to an air regulator, then adjust the air pressure to 30 PSI. 4. Connect the adapter with the air hose Trigger Stop Trigger Needle to the air regulator (see Figure 4). Chuck Siphon Spray...
-
Page 9: Section 4: Operations
SECTION 4: OPERATIONS Spraying The paint you use with this brush should be thinned to the consistency of 2% milk. Strain paint with a coffee filter when pour- ing it into the jar. Keep in mind that paint dries quickly inside EXPLOSION HAZARD! DO NOT the airbrush. -
Page 10: Section 5: Accessories
SECTION 5: ACCESSORIES G6261—Campbell Hausfeld™ Water H7274—Campbell Hausfeld™ Pressure Filter Regulator Remove damaging water vapor before it Mini Series. Provides regulated output reaches your pneumatic tools. This highly pressure of 0 to 125 PSI for proper tool effective, five micron filter features a see- operation. -
Page 11: Section 6: Maintenance
SECTION 6: MAINTENANCE Cleaning 4. Disassemble the airbrush components as shown on the parts breakdown, located on Page 13. Proper cleaning is the best way to ensure 5. Clean the components in a glass or trouble free performance from your air- plastic container with the appropriate brush. -
Page 12: Troubleshooting
Troubleshooting Symptom Possible Cause Solution Excessive over- 1. Spray pattern adjusted incor- 1. Adjust the spray regulator. spray. rectly for your application. 2. Air press too high. 2. Reduce air pressure. 3. Airbrush is too far from sur- 3. Keep airbrush at recom- face. - Page 13 Parts Breakdown G5354 �� �� �� � �� �� �� �� ����������������� � � �� � � �� �� �� � �� � � �� �� �� �� �� PART # DESCRIPTION P5354001 AIR BRUSH FRAME P5354002 O-RING 19.8 X 2.4 P20 P5354003 SPRAY NOZZLE P5354004...
-
Page 14: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. - Page 15 ____70+ How long have you been a woodworker/metalworker? ____0-2 Years ____2-8 Years ____8-20 Years ____20+ Years How many of your machines or tools are Grizzly? ____0-2 ____3-5 ____6-9 ____10+ Do you think your machine represents a good value? ____Yes ____No...
- Page 16 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE...