Piega PS 1 User Manual
Active-subwoofer
Hide thumbs
Also See for PS 1:
- Specifications (6 pages) ,
- User manual (13 pages) ,
- Specification (6 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Piega PS 1
Summary of Contents for Piega PS 1
- Page 1 PIEGA User Manual PIEGA PS 1 / PS 2 Active-Subwoofer...
- Page 2 By purchasing a loudspeaker from PIEGA you have expressed your trust in our company, for which we thank you very much. At the same time we assure you that you have purchased a product that is based on twenty years of R &...
-
Page 3: Table Of Contents
Contents This user manual describes how to connect the PIEGA active subwoofer to different loudspeaker con- figurations and the appropriate setting options for optimum operation in stereo and home cinema mode. It also contains instructions for unpacking and setting up the subwoofer. -
Page 4: Precautions
Precautions Please read this user manual carefully and pay special attention to the following precautions and warnings. In your own interest, we advise you to strictly observe the following procedure when installing your new PIEGA subwoofer. Safety Precautions / Warnings: The PIEGA subwoofers have been designed for use with PIEGA loudspeaker products. -
Page 5: Unpacking
Unpacking Special care was taken in the packaging of your subwoofer in order to ensure that this new PIEGA quality product reaches your living room safely and undamaged. In order to avoid any damage when unpacking the loudspeaker, follow closely the instructions below. -
Page 6: Positioning
Do not in any way prevent the free movement of the subwoofers. To avoid any possible accident, do not place any ob- jects such as vases etc. on your PS 1 / PS 2. PIEGA PS 1 / PS 2 User Manual... -
Page 7: Terminal Area
120 V) of your subwoofer corresponds to the POWERED SUBWOOFER standard supply voltage in your country Plug the supply cable provided with the PS 1 / PS 2 into the appropriate socket WARNING: SHOCK HAZARD DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR... -
Page 8: Setup Procedure
LFE Speaker R Speaker L Please use a suitable connection cable with cinch plugs (not supplied with the PS 1 / PS 2) Connect the front, rear and center loudspeakers us- ing the loudspeaker terminals provided on your AV receiver... - Page 9 Connect the subwoofer cable on the amplifier at the PRE OUT (or similar) terminal and at the LINE IN Connect the PS 1 / PS 2 on the amplifier at the MAIN IN (or similar) terminal and at the LINE OUT terminal...
- Page 10 Surround mode because of overcharge of small satellite speakers). In this configuration the PS 1 / PS 2 will be connected to the amplifier. Refer to the appropriate manual for information about operation and connection options for your stereo amplifier.
-
Page 11: Setting The Sound Characteristics
AUTOMATIC STANDBY Use this switch to activate the standby function of the PS 1 / PS 2. This enables the subwoofer to switch on automatically as soon as a signal is received and to switch off when there is no more signal. When MIN •... -
Page 12: Daily Use
Daily Use From development to production, right down to quality testing, PIEGA only uses materials and components of the highest quality. The Top of your new subwoofer has a polished aluminum surface. As this material is very sensitive, it should be treated with care. -
Page 13: Warranty
Piega. 5. If it is necessary for a device or part of it to be sent to Piega or an approved Piega workshop, the sender is responsible for paying all transport costs in advance. The original packaging must be used for sending the complete device. - Page 14 PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen Telephone +41 44 725 90 42 Fax +41 44 725 91 92 mail@piega.ch www.piega.ch Information for Exports PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen Telephone +41 44 725 90 02 Fax +41 44 725 91 92 mail@piega.ch...