Related Manuals for CyberPower OL6000ERT3U
Summary of Contents for CyberPower OL6000ERT3U
- Page 1 User’s Manual OL6000ERT3U OL8000ERT3U OL10000ERT3U CyberPower Systems Inc. www.cpsww.com K01-0000194-00...
-
Page 2: Important Safety Instructions
REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES! CAUTION! Do not use an improper size power cord as it may cause damage to your equipment and cause fire hazards. Copyright © 2011 CyberPower Systems, Inc. - Page 3 Rackmount right rail * 2 sets Plastic washers (8) * 2 sets Phone line Screw hole dust covers (12) * 2 sets USB communication cable Power cords PowerPanel® Business Edition software CD Serial Interface Cable (RS-232) Copyright © 2011 CyberPower Systems, Inc.
-
Page 4: Hardware Installation
Step 5: Place the internal battery trays back into the Battery module (See page 17) Once completed, perform the same steps for the Power module. CAUTION! The Battery module must be installed below the Power module. Copyright © 2011 CyberPower Systems, Inc. -
Page 5: Vertical/Tower Installation
Do not work alone under hazardous conditions. CAUTION! In case of the risk of electric shock, do not remove the top cover. CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected. Copyright © 2011 CyberPower Systems, Inc. -
Page 6: Installing Your Ups System
UPS will continuously emit two beeps per second. For resetting the unit, unplug some equipment from the outlets. Make sure your equipment carries a load current within the unit’s safe range, (refer to the technical specifications). Copyright © 2011 CyberPower Systems, Inc. -
Page 7: Hardwiring The Input/ Output Terminals
Step 2: Fix the bottom cover on the terminal block Loosen the four screws to separate the top and bottom covers. Tighten the two screws to fix the bottom cover on the terminal block. Copyright © 2011 CyberPower Systems, Inc. - Page 8 Connect the three wires to the output terminal block. Connect the three wires to the input terminal block. Step 5: Fix the top cover on the bottom cover Tighten the six screws to fix the top cover on the bottom cover. Copyright © 2011 CyberPower Systems, Inc.
-
Page 9: Backfeed Protection
“Backfeed Protection Connector” as shown in the following diagram. The external isolation device must be installed in the Mains path. Mains L N PE IP-L IP-N PSDR 2A Fuse Backfeed (Slow Blow) AC-L AC-N Copyright © 2011 CyberPower Systems, Inc. -
Page 10: Basic Operation
Edition Agent software on the PC/Server connected with the USB cord. 15. Extended Runtime Battery Module Connector Connection for additional CyberPower XL Battery modules. 11. Remote Control Port Connects to remote LCD module to the UPS. 16. EPO (Emergency Power Off) Connector Enables an emergency UPS Power-Off from a remote location. - Page 11 Step 3: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable. Step 4: Use a power cord to plug AC input inlet of the battery module into a wall receptacle. Copyright © 2011 CyberPower Systems, Inc.
- Page 12 Step 4: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable. Step 5: Use a power cord to plug AC input inlet of the 2 battery module into AC output outlet of the 1 Battery module. Copyright © 2011 CyberPower Systems, Inc.
-
Page 13: Led Indicators - Ups Status
Press this button to scroll up in the LCD menu. ▼ Press this button to scroll down in the LCD menu. ENTER Press this button to select an option. Press this button to cancel or return to previous LCD menu. Copyright © 2011 CyberPower Systems, Inc. -
Page 14: Lcd Setup Functions
Date & Time Displays the present Date & Time - - - - / - - / - - - -:- - Next BAT Change Displays the next Battery Change Date & Time XXX / XXXX Copyright © 2011 CyberPower Systems, Inc. -
Page 15: Lcd Event Log
You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved and started automatically. (See the following table for additional details.) Press the “ESC” button to cancel or return to the previous LCD menu. Copyright © 2011 CyberPower Systems, Inc. -
Page 16: Eco Mode
Alarms” as “Disable” on the LCD module and it will stop warning of any malfunction audibly. Configure MANUAL BATTERY TEST “Battery Test” as “Active” on the LCD module; and it will perform the “Manual Battery Configure Test” Copyright © 2011 CyberPower Systems, Inc. -
Page 17: Lcd Module Remote Control And Wall-Mounting Instructions
Step 4: Mount LCD Module on the Wall SAFETY PRECAUTIONS CAUTION! It must be done by qualified personnel. CAUTION! To avoid electric shock, turn off and unplug the unit before installing REMOTE CONTROL or WALL-MOUNTING INSTRUCTIONS. Copyright © 2011 CyberPower Systems, Inc. -
Page 18: Maintenance
Only use replacement batteries which are certified by Batteries are considered hazardous waste and must be disposed of CyberPower Systems. Use of incorrect battery type is an electrical properly. Contact your local government for more information about hazard that could lead to explosion, fire, electric shock, or short circuit. -
Page 19: Technical Specifications
L x W x H = 26 x 17 x 5.2in. (66 x 43.3 x 13.2cm) Dimensions--Battery Module L x W x H = 26 x 17 x 5.2in. (66 x 43.3 x 13.2cm) Net Weight--Power Module 53lbs(24Kg) Net Weight--Battery Module 167.2lbs(76Kg) 171.6lbs(78Kg) Safety Conformance Approvals CE, C-tick Copyright © 2011 CyberPower Systems, Inc. -
Page 20: Troubleshooting
Internal DC bus voltage is too high or too low. CyberPower Systems Inc. www.cpsww.com © Entire contents copyright 2011 CyberPower Systems Inc., All rights reserved. Reproduction in whole or in part ® ® without permission is prohibited. PowerPanel Business Edition and PowerPanel Personal Edition are trademarks of CyberPower Systems Inc.