Related Manuals for CyberPower OL6000ERT3UP
Summary of Contents for CyberPower OL6000ERT3UP
- Page 1 User’s Manual OL6000ERT3UP OL8000ERT3UP OL10000ERT3UP OL6000ERT3UM OL8000ERT3UM OL10000ERT3UM CyberPower Systems Inc. www.cpsww.com K01‐0000221‐00 ...
-
Page 2: Important Safety Instructions
REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES! CAUTION! Do not use an improper size power cord as it may cause damage to your equipment and cause fire hazards. 1 Copyright © 2011 CyberPower Systems, Inc. ... - Page 3 Rackmount right rail Plastic washers (8) * 2 sets Phone line Screw hole dust covers (10) * 2 sets USB communication cable Power cord Serial Interface Cable (RS-232) PowerPanel® Business Edition software CD 2 Copyright © 2011 CyberPower Systems, Inc. ...
-
Page 4: Hardware Installation
Step 5: Place the internal battery trays back into the Battery module (See page 19) Once completed, perform the same steps for the Power module. CAUTION! The Battery module must be installed below the Power module. 3 Copyright © 2011 CyberPower Systems, Inc. ... -
Page 5: Vertical/Tower Installation
Insert dust covers into the rackmount ear screw holes that are not being used. ELECTRICAL INSTALLATION After completing the hardware installation of the UPS, you are now ready to plug in the UPS and connect your equipment. 4 Copyright © 2011 CyberPower Systems, Inc. ... - Page 6 CAUTION! In case of the risk of electric shock, do not remove the top cover. CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected. 5 Copyright © 2011 CyberPower Systems, Inc. ...
-
Page 7: Installing Your Ups System
MUST be grounded. second. For resetting the unit, unplug some equipment from the outlets. Make sure your equipment carries a load current within the unit’s safe range, (refer to the technical specifications). 6 Copyright © 2011 CyberPower Systems, Inc. ... -
Page 8: Hardwiring The Input/ Output Terminals
Step 1: Remove the inspection window cover Step 2: Remove the terminal block cover Loosen the four screws to remove the inspection window cover. Loosen the four screws to remove the terminal block cover. 7 Copyright © 2011 CyberPower Systems, Inc. ... - Page 9 Tighten the four screws to fix the inspection window cover on the PDU’s. Step 4: Output configuration Insert the output cable through the appropriate cable gland (not included) and connect the three wires to the output terminal block. 8 Copyright © 2011 CyberPower Systems, Inc. ...
-
Page 10: Backfeed Protection Operation
Remove the interconnection wires (Jumper1 / Jumper2) on “Backfeed Protection Connector”. Hardwire the input terminals and “Backfeed Protection Connector” as shown in the following diagram. The external isolation device must be installed in the Mains path. 9 Copyright © 2011 CyberPower Systems, Inc. ... -
Page 11: Basic Operation
13. Extended Runtime Battery Module Connector Serial port provides communication between the UPS and the computer. Connection for additional CyberPower XL Battery modules. The UPS can control the computer’s shutdown during a power outage through the connection while the computer can monitor the UPS and alter 14. - Page 12 “CRITICAL” outlets, while stopping the power supply to 6. Input / Output Connectors equipment connected to “NONCRITICAL” outlets after a designated Use these connectors to attach the PDU or HW PDU to the Power period of time. module. Copyright © 2011 CyberPower Systems, Inc. ...
- Page 13 Step 3: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable. Step 4: Use a power cord to plug AC input inlet of the battery module into a wall receptacle. Copyright © 2011 CyberPower Systems, Inc. ...
- Page 14 Step 5: Use a power cord to plug AC input inlet of the 2 battery module into AC output outlet of the 1 Battery module. Copyright © 2011 CyberPower Systems, Inc. ...
-
Page 15: Led Indicators - Ups Status
Press this button to scroll up in the LCD menu. ▼ Press this button to scroll down in the LCD menu. ENTER Press this button to select an option. Press this button to cancel or return to previous LCD menu. Copyright © 2011 CyberPower Systems, Inc. ... -
Page 16: Lcd Setup Functions
Displays the present Date & Time - - - - / - - / - - - -:- - Next BAT Change Displays the next Battery Change Date & Time XXX / XXXX Copyright © 2011 CyberPower Systems, Inc. ... -
Page 17: Lcd Event Log
You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved and started automatically. (See the following table for additional details.) Press the “ESC” button to cancel or return to the previous LCD menu. Copyright © 2011 CyberPower Systems, Inc. ... -
Page 18: Silencing Audible Alarms
Alarms” as “Disable” on the LCD module and it will stop warning of any malfunction audibly. MANUAL BATTERY TEST Configure “Battery Test” as “Active” on the LCD module; and it will perform the “Manual Battery Test” Copyright © 2011 CyberPower Systems, Inc. ... - Page 19 D MODULE E REMOTE E CONTRO OL and W WALL-MOU UNTING IN STRUCTIO MOTE CONT TROL ALL-MOUNT TING INSTRU UCTIONS Step 1: Remove the M Multifunction LC CD Module Step p 1: Remove the e Multifunction L LCD Module Unscr rew the right pan...
-
Page 20: Maintenance
Only use replacement batteries which are certified by Batteries are considered hazardous waste and must be disposed of CyberPower Systems. Use of incorrect battery type is an electrical properly. Contact your local government for more information about hazard that could lead to explosion, fire, electric shock, or short circuit. -
Page 21: Manual Bypass Switch Operation
Do not slide the Interlock Bracket when the LCD screen shows On” or On”. “Generator “Converter CAUTION! Do not turn the Manual Bypass Switch when hearing a warning beep from the Power module. Copyright © 2011 CyberPower Systems, Inc. ... - Page 22 Do not slide the Interlock Bracket when the LCD screen shows On” or On”. “Generator “Converter CAUTION! Do not turn the Manual Bypass Switch when hearing a warning beep from the Power module. Copyright © 2011 CyberPower Systems, Inc. ...
-
Page 23: Technical Specifications
L x W x H = 32.3 x 17 x 5.2in. (82 x 43.3 x 13.2cm) Dimensions--Battery Module L x W x H = 32.3 x 17 x 5.2in. (82 x 43.3 x 13.2cm) Net Weight--Power Module 63lbs(28.5Kg) Net Weight--Battery Module 167.2lbs(76Kg) 171.6lbs(78Kg) Safety Conformance Approvals CE, C-tick Copyright © 2011 CyberPower Systems, Inc. ... -
Page 24: Troubleshooting
Internal DC bus voltage is too high or too low. CyberPower Systems Inc. www.cpsww.com © Entire contents copyright 2011 CyberPower Systems Inc., All rights reserved. Reproduction in whole or in part ® ® without permission is prohibited. PowerPanel Business Edition and PowerPanel Personal Edition are trademarks of ...
Need help?
Do you have a question about the OL6000ERT3UP and is the answer not in the manual?
Questions and answers