Subscribe to Our Youtube Channel
Related Manuals for CyberPower OL6000E
Summary of Contents for CyberPower OL6000E
- Page 1 User’s Manual OL6000E OL8000E OL10000E CyberPower Systems Inc. www.cpsww.com K01-0000240-02...
-
Page 2: Important Safety Instructions
REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES! CAUTION! Do not use an improper size power cord as it may cause damage to your equipment and cause fire hazards. Copyright © 2012 CyberPower Systems, Inc. - Page 3 UNPACKING User’s manual Register card Phone line USB communication cable Serial Interface Cable (RS-232) PowerPanel® Business Edition software CD Input / Output terminal block cover Copyright © 2012 CyberPower Systems, Inc.
-
Page 4: Installing Your Ups System
UPS will continuously emit two beeps per second. For resetting the unit, unplug some equipment from the outlets. Make sure your equipment carries a load current within the unit’s safe range, (refer to the technical specifications). Copyright © 2012 CyberPower Systems, Inc. -
Page 5: Hardwiring The Input/ Output Terminals
CAUTION! Disconnected EPO will immediately shut down the logic circuit output of the UPS. Wiring the EPO signal is optional. CAUTION! Local safety rules may require a separate, external EPO to turn off output circuit breakers. Refer to local wiring rules, the EPO should use approved components. Copyright © 2012 CyberPower Systems, Inc. - Page 6 Insert the input cable through the appropriate cable gland (not included). Step 3: Bypass configuration (for dual input configuration) Remove the interconnection wires (Jumper) on bypass terminals (J / L) and insert the bypass cable through the appropriate cable gland (not included). Copyright © 2012 CyberPower Systems, Inc.
- Page 7 Insert the output cable through the appropriate cable gland (not included) Step 6: Fix the top cover on the bottom cover Tighten the six screws to fix the top cover on the bottom cover. Copyright © 2012 CyberPower Systems, Inc.
-
Page 8: Backfeed Protection
3. Hardwire the input terminals and “Backfeed Protection Connector” as shown in the following diagram. 4. The external isolation device must be installed in the Mains path. Mains L N PE IP-L IP-N PSDR 2A Fuse Backfeed (Slow Blow) AC-L AC-N Copyright © 2012 CyberPower Systems, Inc. -
Page 9: Basic Operation
Slot to install the optional SNMP card for remote network control and monitoring. 15. Extended Runtime Battery Module Connector Connection for additional CyberPower XL Battery modules. 16. EPO (Emergency Power Off) Connector Enables an emergency UPS Power-Off from a remote location. -
Page 10: Led Indicators - Ups Status
Press this button to scroll up in the LCD menu. ▼ Press this button to scroll down in the LCD menu. ENTER Press this button to select an option. Press this button to cancel or return to previous LCD menu. Copyright © 2012 CyberPower Systems, Inc. -
Page 11: Lcd Setup Functions
Date & Time Displays the present Date & Time - - - - / - - / - - - -:- - Next BAT Change Displays the next Battery Change Date & Time XXX / XXXX Copyright © 2012 CyberPower Systems, Inc. -
Page 12: Lcd Event Log
You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved and started automatically. (See the following table for additional details.) Press the “ESC” button to cancel or return to the previous LCD menu. Copyright © 2012 CyberPower Systems, Inc. -
Page 13: Eco Mode
Configure “Audible Alarms” as “Disable” on the LCD module and it will stop warning of any malfunction audibly. MANUAL BATTERY TEST Configure “Battery Test” as “Active” on the LCD module; and it will perform the “Manual Battery Test” Copyright © 2012 CyberPower Systems, Inc. -
Page 14: Lcd Module Remote Control And Wall-Mounting Instructions
Step 4: Mount LCD Module on the Wall SAFETY PRECAUTIONS CAUTION! It must be done by qualified personnel. CAUTION! To avoid electric shock, turn off and unplug the unit before installing REMOTE CONTROL or WALL-MOUNTING INSTRUCTIONS. Copyright © 2012 CyberPower Systems, Inc. -
Page 15: Maintenance
Only use replacement batteries which are certified by Batteries are considered hazardous waste and must be disposed of CyberPower Systems. Use of incorrect battery type is an electrical properly. Contact your local government for more information about hazard that could lead to explosion, fire, electric shock, or short circuit. -
Page 16: Manual Bypass Switch Operation
CAUTION! Do not remove the Interlock Cover when the LCD screen replacement now. shows “Generator On” or “Converter On”. CAUTION! Do not turn the Manual Bypass Switch when hearing a warning beep from the UPS. Copyright © 2012 CyberPower Systems, Inc. -
Page 17: Technical Specifications
® Power Management Software PowerPanel Business Edition Physical Dimensions L x W x H = 26 x 10.4 x 23.6in. (66 x 26.5 x 60cm) Net Weight 209lbs(95Kg) 213.4lbs(97Kg) Safety Conformance Approvals CE, C-tick Copyright © 2012 CyberPower Systems, Inc. -
Page 18: Troubleshooting
Internal DC bus voltage is too high or too low. CyberPower Systems Inc. www.cpsww.com © Entire contents copyright 2012 CyberPower Systems Inc., All rights reserved. Reproduction in whole or in part ® ® without permission is prohibited. PowerPanel Business Edition and PowerPanel Personal Edition are trademarks of CyberPower Systems Inc.
Need help?
Do you have a question about the OL6000E and is the answer not in the manual?
Questions and answers