Operation - American DJ Revo Roll LED User Instructions

Revo Roll LED™
Operating Modes: The Revo Roll LED™ can operate in three
different modes. This next section will detail the differences in
the operating modes.
• Sound Active mode -
The unit will react to sound.
• Master/Slave mode -
You can daisy chain up to 16 units together to get a synchronized
light show without the need of an external controller. The units will
react to sound chasing through the several built-in programs.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation
Designer.
™
Universal DMX Control:
universal DMX-512 controller to control mirror movement, the pat-
terns and chases, and the strobe. A DMX controller allows you to cre-
ate unique programs tailored to your individual needs.
1. The Revo Roll LED™ uses four DMX channels. See page 13 for
detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller's faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 8 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Stand-Alone Operation (Sound Active Mode):
a single unit or several units linked together, to run to the beat of the
music.
1. Once you plug the fixture in, Sound Active mode is activated auto
.
matically
2. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
American DJ - www.americandj.com - Revo Roll LED™ Instruction Manual Page 11
®
This function allows you to use a Elation
This mode allows

Operation

Revo Roll LED™
Master-Slave Operation (Sound Active):
you to link up to 16 units together and operate without a controller. The
units will be sound activated. In Master-Slave operation one unit will
act as the controlling unit and the others will react to the controlling
units programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR
connector is the output. The first unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
Show
2. On the Master unit find your desired show and set that show by
®
pressiing the ENTER button.
3. On the slave units
®
played, and Press ENTER.
4. The slave units will now follow the Master unit.
Note: When running fixtures in Master/Slave configuration "SL
1" will make the fixture do the opposite to the other fixture.
Example: Four fixtures linked together. On fixtures 1 and 3 set
the fixtures to "SL 1", and set fixtures 2 & 4 to "SL 2". Fixtures 1 & 2
will run the same and fixtures 2 & 4 will run opposite. This makes
a great light show.
5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Revo Roll LED™
First unplug the power. The fuse holder is located next to the power
cord. Using a flat-head screw driver unscrew the fuse holder. Remove
the bad fuse and replace with a new one.
Revo Roll LED™
Stand by
Function
Mode
American DJ
tap the MENU button until "SLND" is dis
Blackout the unit
1. Sync. Strobe
Select pattern
2. Sound Strobe
Sound Pattern
(LED OFF) (LED ON)
- www.americandj.com - Revo Roll LED™ Instruction Manual Page 12
®
Operation
This function will allow
Fuse Replacement
UC3 Control
Select Chase
Chase
(LED Slow Strobe)