Related Manuals for Dometic Eskimo Ice 600
Summary of Contents for Dometic Eskimo Ice 600
- Page 1 Eskimo Ice 600 Installation/Owners Manual Self Contained Ice Making System Revised: 5-5-06 L-2448A...
- Page 2 Technical Support Information Copyright 2005 Dometic Environmental Corporation, All Rights Reserved - Every precaution has been taken in the preparation of this manual to insure its accuracy. However, Dometic Environmental Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of this product and information contained herein.
- Page 3 Installation Instructions for E.I. 600 Read all instructions before starting the installation Locating ice machine Locate flat level platform for E.I.600. Do not place where salt spray is present or corrosion problems will result. Locate so that electrical control panel (with off/on switch) faces out for easy access. Test routing of 1 1/4"...
- Page 4 Ice delivery hose installation detail We are using a thru-hull fitting for delivery of ice into storage box. Drill hole for thru-hull fitting in storage box. Make this hole 2 3/8" in diameter. (See drawing #6.) Also see yellow template in temperature control box.
- Page 5 install the male plug to the pump wire (green wire to green screw, black to brass, and white to silver, 115V). (green to green, black and white to brass for 230VInsert male plug on pump into female on the pigtail attached to the machine, if desired pigtail and plugs can be eliminated, and pump wires directly into electrical control box.
- Page 6 Thermostat installation and wiring of the E.I. 600 Installation of temperature control This ice machine uses a Ranco ETC control. We recommend mounting in an accessible location near the unit. Since this control has an LED indictor and switches which can be useful in monitoring and testing the ice machine, a convenient location is preferred.
- Page 7 Corrosion control Covering all electrical components and wiring connections with a corrosion product will help reduce corrosion problems years into the future. The complete ice machine can be coated with a spray like Corrosion Block. Winterizing-warning See note on below freezing temperatures in trouble shooting section #11. Warranty card Please fill out upper portion of warranty card, affix stamp and mail back promptly.
- Page 10 Drawing #5 Drawing #6 Drawing #4...
- Page 12 ICE HOSE TERMINATION FOR REMOVABLE FISH BOXES Drop in Fish Box Drawing #9...
- Page 13 Eskimo Ice 600 - Start up procedure form (check mark each box after completion of each step ) 1. Record 9-digit Eskimo Ice Serial Number (on front of ice machine): _________________ Place toggle switch on front of ice machine to “off” position ( down ) Open freshwater shut off valve.
- Page 14 Trouble shooting the E.I. 600 if not producing ice 1. Check to see if power is reaching the ice machine. If raw water pump is running, power is reaching the machine. If power light on temperature control is on, power is reaching ice machine.
- Page 15 7. Check fresh water supply pressure by removing cover to water reservoir and pushing down float from valve. (Water should be running strongly.) The machine is equipped with a low water pressure switch which will not allow machine to run if there is less than 10 lbs. of fresh water pressure.
- Page 16 11. If the ice machine is to be exposed to temperatures below freezing (32°F), water must be drained from machine or potable anti-freeze must be added to the fresh water supply and flushed through the machine. If you suspect that untreated water has been left in the ice machine at temperatures below freezing and water in the ice maker has frozen, drive motor will be locked up, and will not start.
-
Page 17: Control Box
Low pressure control is set at approximately +2 lbs. The low pressure control can be tested by holding up the water float in the water reservoir and dropping the temperature and pressure in the evaporator causing the low to trip. High pressure control is set at approximately 250 lbs. - Page 18 M ai nt enance Turn unit off before performing any maintenance. M ont hl y 1. Check the Strainer in the water filter on the fresh water fill to make sure it’s clean. 2. Check the Water Reservoir to make sure it’s clean and not overflowing. 3.
- Page 25 Ranco ETC Ther m i s t or pr e- w i r ed A dd J um per ‘ 24V A C’ t er m i nal A dd J um per ‘ C’ t er m i nal Requi r es j um per f r om ‘...
- Page 26 V E R G W D...
-
Page 27: Technical Assistance
TECHNICAL ASSISTANCE Applications: Dometic Environmental Corporation 2000 N. Andrews Ave. Ext. Pompano Beach, FL 33069-1497 USA Phone: 954-973-2477 Facsimile: 954-979-4414 Dometic Environmental Corporation P.O. Box 15299 Richmond, VA 23227-0699 US Phone: 804-746-1313 Facsimile: 804-746-7248 Service: Dometic Environmental Corporation 2000 N. Andrews Ave. Ext. - Page 28 Dometic Environmental Corporation 2000 N. Andrews Ave. Ext. • Pompano Beach, FL 33069-1497 USA • Phone: 954-973-2477 • Facsimile: 954-979-4414 P.O. Box 15299 • Richmond, VA 23227-0699 USA • Phone: 804-746-1313 • Facsimile: 804-746-7248 Website: www.dometicenviro.com • Email: sales@dometicenviro.com L-2448A...