Autotek SM1600.2 Instructions Manual
  1. Manuals
  2. Brands
  3. Autotek Manuals
  4. Amplifier
  5. SM1600.2
  6. Instructions manual

Autotek SM1600.2 Instructions Manual

Street machine series amplifiers
Hide thumbs

Advertisement

Table of Contents

R
EVOLUTION OF POWER
STREET MACHINE
AMPLIFIERS
SM1600.2 / SM1400.4
SM3200.1 / SM4800.1 / SM6000.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SM1600.2 and is the answer not in the manual?

Questions and answers

Related Manuals for Autotek SM1600.2

Summary of Contents for Autotek SM1600.2

  • Page 1 EVOLUTION OF POWER STREET MACHINE AMPLIFIERS SM1600.2 / SM1400.4 SM3200.1 / SM4800.1 / SM6000.1...

  • Page 2: Table Of Contents

    STREET MACHINE SERIES AMPLIFIERS Congratulations on your purchase and thank you for supporting AUTOTEK! The STREET MACHINE Series products have been designed to a very high level of performance, with features unavailable in similarly priced amplifiers. These amplifiers have variable crossovers built in, with added touches such as subsonic filter, bass equalization and a remote Level control module (some models) that allows subwoofer Level control from the drivers seat.

  • Page 3: General Installation Procedure

    GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion.

  • Page 4: Amplifier Feature Descriptions

    Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps All Autotek amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and amplifier DC which are capable of 4, 2 and 1-Ohm loads.

  • Page 5: Sm1600.2 2-Channel Amplifier Applications

    TO BATTERY +12v VIA FUSE REMOTE TURN-ON CHASSIS GROUND MONO This application illustrates the basic mono bridging method for all Autotek amplifiers. Switch setting checklist: - The AMPLIFIER X-OVER switch should be in the LPF position and the MODE Interconnect cable checklist:...

  • Page 6: Sm1400.4 4-Channel Amplifier Applications

    SM1400.4 4-CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straight forward discrete 4 - HI PASS: N/A channel full range units. The MODE switch should be in 4CH. - LOW PASS: N/A Interconnect cable checklist: Channels 3/4: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
  • Page 7 SM1400.4 4-CHANNEL AMPLIFIER APPLICATIONS Front/Rear high pass, using a 2 channel amplifier for mono sub bass The combination of a 2 and a 4 channel amplifier, utilizing their built in Channels 1/2: crossovers, makes it a snap to put together a full system with front and rear - HI PASS: 100 Hz highs, with mono sub bass.

  • Page 8: Sm3200.1 / Sm4800.1 / Sm6000.1 1 Channel Amplifier Applications

    SM3200.1 / SM4800.1 / SM6000.1 MONO AMPLIFIER APPLICATION Basic application These sub bass amplifiers can be used in any of the bi-amplification systems described in Crossover frequency control checklist: this manual, replacing the 2 channel amplifiers as per the illustrations. LOW PASS: 40Hz to 150Hz SUBSONIC:15 Hz to 55 Hz Interconnect cable checklist:...

  • Page 10: Setting Up Systems After Installation For Best Performance

    SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE SM1600.2 / SM1400.4 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in HPF operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point.

  • Page 11: Troubleshooting And Diagnostics

    The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Autotek amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker leads.

  • Page 12: Product Warranty

    Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase.
  • Page 13 Accessories OUTPUT LEVEL CONTROL 4.5V 2.5V FREQUENCY CENTER RANGE FREQUENCY GROUND ISOLATION WIDE NARROW GROUND 200-Ohms ISOLATED BASS CREA TOR DIGITAL BASS RESTORATION MBC1 INPUT BALANCED UNBALANCED INPUT OUTPUT REMOTE REM / 12V / GND The MBC1 contains a BASS DRIVER circuit that accurately recreates and injects Low Frequency information back into the signal path.

  • Page 14: Oem Integration Accessories

    OEM Integration Accessories MX-1 Premium High To Low Level Converter MX-3 Bass Controller * Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Outputs * High Level Inputs: Accepts all types of High level Inputs * Parametric Bass EQ: Provides a wide array of subwoofer output signal including floating ground and high voltages up to 30 volts.
  • Page 16 PART: S0412...

This manual is also suitable for:

Sm4800.1Sm1400.4Sm6000.1Sm3200.1

Table of Contents