White 1525 Instruction Manual
  1. Manuals
  2. Brands
  3. White Manuals
  4. Sewing Machine
  5. 1525
  6. Instruction manual

White 1525 Instruction Manual

Sewing machine
Hide thumbs Also See for 1525:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for White 1525

Summary of Contents for White 1525

  • Page 3: Table Of Contents

    CONTENTS Name of Parts 1 &2 Accessories Before sewing (Power supply and Sewing amp). Take out extension table, free arm sewing Winding the bobbin Removing bobbin case and bobbin Inserting bobbin into bobbin case Inserting bobbin case into shuttle race Threading upper thread &...
  • Page 5 (REAR VIEW) Bobbin winder spindle Bobbin winder stopper thread guide Stop Hand wheel Face cover plate Needle clamp screw Presser foot lever —2—...

  • Page 6: Accessories

    ACCESSORI ES Felt Zigzag foot Bobbin Button hole foot (On machine> Button foot Machine Oil Zipper foot Button hole cutter Screw driver Needle #14. —3—...

  • Page 7: Before Sewing (Power Supply And Sewing Amp)

    BEFORE SEWING 1. Fit the machine plug into the machine. 2. Plug machine power supply. 3. Sewing speed can be varied by the speed controller. 1. Remove or install bulb from inside of face cover. 2. Open face cover in direction of arrow.
  • Page 9 is corn-U >( :::% .

  • Page 10: Removing Bobbin Case And Bobbin

    REMOVING BOBBIN CASE AND BOBBIN Hinged latch latch 1. Raise needle to its highest hinged 2. Open bobbin case and pull bob open position bin case out of machine. shuttle race cover. 3. Release the latch and bob bin will fail out easily. INSERTING BOBB!N INTO BOBBIN CASE off 5cm of thread 2.

  • Page 12: Threading Upper Thread & Twin Needle Threading

    THREADING UPPER THREAD Twin needle threading —...

  • Page 13: Drawing Up Bobbin Thread

    DRAWING UP BOBBIN THREAD 1. Hold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper thread will be brought up in a loop.
  • Page 14 LEVELJNG MACHINE DOWN —11—...
  • Page 15 ADJUSTING THREAD TENSION Correct 1• Upper thread Fabric Strong Weak Bobbin thread Upper thread tension may be adjusted by turning the thread tension dial. Incorrect Inside of fabric Upper thread Lower thread tension can be adjusted by turning bobbin case screw on right slightly...

  • Page 18: Fabric, Thread. Needle Table

    — — —...

  • Page 19: Sewing (Pattern Selector) And Operation Table

    I— F— 16— —...
  • Page 21 3—4...

  • Page 22: Zigzag Sewing

    ____...

  • Page 23: Straight Stitch

    OVERCASTING ‘V Use these stitches for oversewiiig rough edges. STRAIGHT STRETCH STITCH Use this stitch with knitted, tricot other stretchy fabrics. The stitch enables your seam to stretch without breaking the thread. It is also a very strong straight stitch for areas under stress.

  • Page 24: Blind Stitch 21&22

    ______ BLIND STITCH 1. Fold fabnc as shown. 2. To finish seam as shown. — —...
  • Page 25 Adjust width and needle position to obtain correct seam. Needle is not piercing Needle is pierces edge edge of fold at all. of fold too much. Correct seam —22—...

  • Page 26: Button Sewing

    .., .,...

  • Page 27: Zipper Sewing

    sew as — —...

  • Page 28: Button Hole Sewing

    • — —.

  • Page 29: Hemming

    a little — —...

  • Page 31: Quilter

    — —...

  • Page 32: Maintenance (Cie.ning And Oiling)

    MAINTENANCE (CLEANING AND OILING) 1. Raise needle to its highest position. 2. Take out bobbin case. 3. Turn latch knob A as illustrated. 4. Take off shuttle race cover. 5. Take out shuttle hook, 6. Clean and oil shuttle race and hook, then replace in the reverse order.

This manual is also suitable for:

X-17

Table of Contents