Table of Contents
Advertisement
Example: To program your TV,
Cable Box and the AVR35 to turn on
when the Power button is pressed,
first press-and-hold the
and
buttons
`
Mute
light comes on under the
ton. Next, press the
Mute
to enter the Power command
`
for the AVR. Press the
Control Selector c
the TV mode, and then press the
button
again, to select
`
Mute
TV Power. Finally, press the
Device Control Selector c
followed by the
Mute
to select Cable Power. Press the
buttons
⁄
¤
Channel
/
enter the commands.
After following these steps, each time
you press the
button
Power
remote will send the Power On/Off
command each time the Power
button is pressed.
To remove a macro program, follow steps
1, 2 and 4 above, but do not follow step
three. For example, to erase the macro
just entered, press the
Device Control
Selector c
and the
Mute
at the same time until the red light
under the Device Control Selector turns
on. Press the
button
Power
then press the
⁄
Channel
. The red light under the
f
will blink twice to
Control Selector
confirm the data entry and then turn off.
NOTE: Only the
button
AVR
the
button
may be pro-
c
SAT/CBL
grammed for macros.
Volume Punch-Through
The AVR35's remote may be programmed
to operate the
Volume Controls
from either the TV or the AVR to operate in
Programming the Remote
conjunction with any of the eight devices
controlled by the remote. For example,
since the AVR35 will likely be used as the
AVR b
sound system for TV viewing, you may
until the red
wish to have the AVR's volume activated
but-
although the remote is set to run the TV.
AVR
button
Either the AVR or TV volume control may
be associated with any of the remote's
devices. To program the remote for Volume
TV Device
to select
Punch-Through, follow these steps:
1. Press the
for the unit you wish to have asso-
c
CBL
ciated with the volume control and the
button
`
Mute
until the red light illuminates under
to
the
f
Device Control Selector
2. Press the
, the
3. Press either the
d
Device Control Selector c
depending on which system's volume
control you wish to have attached for
the punch-through mode. Note that
the red light under the
Control Selector
and then go out to confirm the data
entry.
button
`
Example: To have the AVR's
volume control be activated even
, and
though the remote is set to control
d
buttons
the TV, first press the
¤
/
Control Selector c
Device
Mute
Next, press the
and
b
Control Selector b
NOTE: Should you wish to return the
remote to the original configuration after
entering a Volume Punch-Through, you
will need to repeat the steps shown above.
However, press the same Device Control
Selector in steps one and three.
31
Device Control Selector
button
at the same time
`
.
button
Volume Up
or the
AVR b
TV
,
Device
will blink twice
TV Device
and the
button
at the same time.
`
button
Volume Up
followed by the
AVR Device
.
Re-Assigning Device Control
Selectors
Although each of the seven
Control Selectors c
assigned to the category of product shown
on the remote, it is possible to re-assign
one of these buttons to operate a second
device of another type. For example, if you
have two VCRs, but no satellite receiver,
you may program the "SAT" button to
operate a second VCR. Before following
the normal programming steps for either
Three-Digit entry or Auto Search code
entry, you must first re-assign the button
with the following steps:
1. Press the
Device Control Selector
you wish to re-assign and the
c
.
button
`
Mute
until the red light illuminates under
the
Device Control Selector
2. Press the
Device Control Selector
c
for the function you wish to
program into the re-assigned button.
3. Enter the three-digit code for the spe-
cific model you wish the re-assigned
button to operate.
4. Press the same
pressed in Step 1 again to
Selector
store the selection.
Example: To use the SAT button to
operate a second VCR, first press the
SAT Device Control Selector
, and the
c
Mute
the same time until the red light
glows under the SAT button. Press
the VCR button, followed by the
three-digit code for the specific
model you wish to control. Finally,
press the SAT button again.
Device
is normally
at the same time
.
Device Control
button
at
`
Hide quick links:
Advertisement
Table of Contents
