1. Manuals
  2. Brands
  3. GTO Manuals
  4. Intercom System
  5. F3100
  6. Installation manual

GTO F3100 Installation Manual

Wireless gate entry intercom/keypad
Hide thumbs Also See for F3100:
Table of Contents

Advertisement

Quick Links

See also: Quick Manual
IMPORTANT:
intercom base unit's battery
to charge for 12 hours before
using the system for the first
time. See page 6 for details.
Wireless Gate Entry Intercom/Keypad
Instructions for Wireless and Wired Installations
Crystal clear two-way communication up to 500 feet wireless or 1000 feet wired.
Thank you for purchasing the GTO Wireless Gate Entry Intercom/Keypad. Be sure to read the
directions carefully and completely. Before permanently mounting the intercom/keypad, please
program the keypad and test its range.
IMPORTANT: Your intercom/keypad may need to be hard wired due to the fact that it must
accept interference according to FCC regulations listed below. For example, applications that
are relativity close to cell towers or airports may receive intermittent interference and require
hard-wiring.
In areas of high radio frequency (RF) interference, the keypad may need to be connected (hard
wired) directly to the gate opener using 16 gauge (AWG) stranded, direct burial, low voltage
wire (part no. RB509 not included).
Also in areas of high radio frequency (RF) interference, the intercom base unit may need to be
hard wired to the keypad using co-ax (cable TV cable not included) .
SAFETY NOTE: Never install the keypad portion of this unit where a person
can reach through the gate to activate it, or where a person can touch the gate
while activating the keypad. The recommended minimum distance between the
gate and keypad is 10 ft.
Telephone (850) 575-0176 • Fax (850) 575-8912 • website www.gtoinc.com
rev - 06-17-05
Allow the
GTO, Inc. • 3121 Hartsfield Road • Tallahassee, Florida 32303
©2005 GTO, Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F3100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GTO F3100

Summary of Contents for GTO F3100

  • Page 1 Instructions for Wireless and Wired Installations Crystal clear two-way communication up to 500 feet wireless or 1000 feet wired. Thank you for purchasing the GTO Wireless Gate Entry Intercom/Keypad. Be sure to read the directions carefully and completely. Before permanently mounting the intercom/keypad, please program the keypad and test its range.
  • Page 2 Features of the Intercom/Keypad The intercom/keypad has two separate units. The keypad (outside unit) should be mounted outside the gate allowing the driver of the vehicle approaching the property to press the CALL button from their vehicle. The base (inside unit), with it’s rechargable battery, can be plugged into any 110 Volt AC outlet for use while charging.

  • Page 3: Keypad Description

    This button is used only when there is another NOTE: Four (4) AA batteries (not included) are required to power the pair of GTO wireless intercom units nearby keypad. If an external DC power supply such as the gate opener’s power causing interference.

  • Page 4: Control Board Connections

    See Programming the Keypad section. Control Board Connections NOTE: If your control board doesn’t look like any of these diagrams, please call GTO Technical Service at 1-800-543-1236 or 850-575-4144 for additional support. Mighty Mule 350 Control Board Mighty Mule 250 E-Z Gate Opener...

  • Page 5: Programming The Keypad

    Programming the Keypad Programming Interface: Program (Add) New Temporary Entry Code: • All codes are four (4) digits in length. • Press and release PROGRAM button. • Entry code is a four (4) digit code needed to activate the gate. •...

  • Page 6: Intercom Description

    Intercom - Bottom VOLUME Control: Controls volume level of speaker. BATTERY ACCESS Cover: Rechargable 3.6 Volt Ni-Cd battery included. ID SET button: This button is used only when there is another pair of GTO wireless intercom units nearby causing interference.

  • Page 7: Intercom Installation

    Intercom Installation Connecting the Battery Remove the battery access cover using a small phillips head screwdriver. Plug the rechargeable Ni-Cad battery into the receptacle inside the battery compartment. See diagram to the right. When this is done, replace the battery access cover. Battery Plug Approved 110 Vac outlet Battery...
  • Page 8 Hard Wiring Intercom Base to Keypad In areas of high radio frequency (RF) interference, the intercom may not work as a wireless system. In these areas the keypad antenna will need to be extended (run closer to the house) using co-axial cable, which is the same type of cable used for cable TV.

  • Page 9: Test The System

    Test the System IMPORTANT: The base unit and the keypad can not be within 30 feet of each other when operating. If units are closer than 30 feet the signal will be inconsistent as well as emit speaker feed back. Have someone press the CALL button on the keypad at the gate.
  • Page 10 fire, flood, insects, or other natural agent. After the one (1) year warranty period, GTO Inc. or one of its authorized service centers will make any necessary repairs for a nominal fee. Call GTO at 850/575-4144 for more information.

This manual is also suitable for:

Pro

Table of Contents