Pi Seek Setting; Setting Pty31 (Emergency Broadcast) Reception; Setting The Time To Automatically Adjust; Receiving Traffic Information - Alpine CDA-9885R Owner's Manual

PI SEEK Setting

1
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
2
Turn the Rotary encoder to select the TUNER
mode, and then press
Bluetooth GENERAL
Bluetooth
3
Turn the Rotary encoder to select PI Seek, and
then press / /ENT.
4
Turn the Rotary encoder to select ON or OFF.
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Setting PTY31 (Emergency Broadcast)
reception
Turn PTY31 (Emergency Broadcast) reception ON/OFF.
1
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
2
Turn the Rotary encoder to select the TUNER
mode, and then press
Bluetooth GENERAL
Bluetooth
3
Turn the Rotary encoder to select Alert PTY31,
and then press /
4
Turn the Rotary encoder to select ON or OFF.
If you set to ON, emergency broadcasts are received
regardless of source. "ALARM" is displayed during
reception.
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
When an emergency broadcast is received, the volume
level will be automatically changed to the memorized level
in the traffic information mode. For details, refer to
"Receiving Traffic Information" on page 10.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
10
-EN
/ /ENT.
AUDIO DISPLAY TUNER
/ /ENT.
AUDIO DISPLAY TUNER
/ENT.

Setting the Time to automatically Adjust

When you set to ON, the time is automatically adjusted by RDS data.
1
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
2
Turn the Rotary encoder to select the TUNER
mode, and then press
Bluetooth GENERAL
Bluetooth
3
Turn the Rotary encoder to select Auto Clock, and
then press / /ENT.
4
Turn the Rotary encoder to select ON or OFF.
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.

Receiving Traffic Information

1
Press and hold BAND/TA for at least 2 seconds so
that the "TA" indicator lights up.
2
Press or to select your desired traffic
information station.
When a traffic information station is tuned in, the "TP"
indicator lights up.
Traffic information is heard only when it is being broadcast.
If traffic information is not being broadcast, the unit is set in
the standby mode. When a traffic information broadcast
begins, the unit automatically receives it and the display
shows "T. INFO".
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
• If the traffic information broadcast signal falls below a certain level,
the unit remains in the receiving mode for 1 minute. If the signal
remains below a certain level for over 1 minute, the "TA" indicator
blinks.
• If you do not want to listen to the traffic information being received,
lightly press BAND/TA to skip that traffic information message. The
TA mode will remain in the ON position to receive the next traffic
information message.
• If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is
received next time, the volume level will be automatically adjusted to
the level memorized.
• In the TA mode, the SEEK tuning selects only the TP stations.
/ /ENT.
AUDIO DISPLAY TUNER